Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 14, Problem 14.12P
A solid rectangular simply supported timber beam
(a) Compute the maximum horizontal shear stress at the neutral axis.
(b) Compute the shear stress
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Calculate the modulus of section of rectangle beam of breadth 120 mm and height 200 mm.
Calculate the end bearing length (in.) required for a 10-in.-by-16-in. timber beam (dressed) that is supported on a reinforced concrete wall as shown. The beam reaction is 18,000 lb and the allowable compressive stress perpendicular to the grain for the timer member is 400 psi. (Unit: in.)
a 80 mm wide and 300 mm high simply supported bean has a length of 7.4 m and supports a concentrated load of 7.2 kN acting at the midspan. Find the maximum shear stress and maximum bending stress.
Chapter 14 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 14 - Calculate the section modulus for: (a) a 6 -in-by-...Ch. 14 - Calculate the section modulus (with respect to the...Ch. 14 - Prob. 14.3PCh. 14 - Rework Problem 14.3 changing the orientation of...Ch. 14 - Assume that the timber member (a) of Problem 14.2...Ch. 14 - The structural steel built-up member (b) of...Ch. 14 - A round steel rod, 25 mm in diameter, is subjected...Ch. 14 - A square steel bar, 38 mm on each side, is used as...Ch. 14 - Calculate the moment strength for a W36302...Ch. 14 - Calculate the allowable bending moment for a solid...
Ch. 14 - The beams of cross sections shown are subjected to...Ch. 14 - A solid rectangular simply supported timber beam 6...Ch. 14 - A W1430 supports the loads shown. Calculate the...Ch. 14 - If the allowable shear stress is 100 MPa,...Ch. 14 - A steel pin 112 in diameter is subjected to a...Ch. 14 - A timber power-line pole is 10 in. in diameter at...Ch. 14 - Calculate the value of S and Z and the shape...Ch. 14 - For beams that have cross sections as shown for...Ch. 14 - Calculate the maximum load P that the beam shown...Ch. 14 - A 412 (S4S) hem-fir timber beam carries a...Ch. 14 - A simply supported W1636 A992 steel beam carries a...Ch. 14 - A W250115 steel wide-flange section supports a...Ch. 14 - Assume that the floor joist dimensions of Example...Ch. 14 - Calculate the allowable superimposed uniformly...Ch. 14 - A 3 -in.-by- 12 -in. (S4S) scaffold timber plank...Ch. 14 - For the following computer problems, any...Ch. 14 - For the following computer problems, any...Ch. 14 - For the following computer problems, any...Ch. 14 - Calculate the section modulus with respect to the...Ch. 14 - The timber box section (a) of Problem 14.29 is...Ch. 14 - A timber beam is subjected to a maximum bending...Ch. 14 - Rework Problem 14.31 assuming that the beam is...Ch. 14 - A 12 -in.-diameter steel rod projects 2 ft...Ch. 14 - Calculate the maximum bending stress in a W530101...Ch. 14 - A cantilever cast-iron beam is 6 ft long and has a...Ch. 14 - 14.36 Calculate the moment strength for a...Ch. 14 - A W813 steel wide-flange beam on a 20 -ft span is...Ch. 14 - A simply supported beam with a cruciform cross...Ch. 14 - A rectangular beam 100 mm in width and 250 mm in...Ch. 14 - The timber box section (a) of Problem 14.29 is...Ch. 14 - For the I-shaped timber beam shown, calculate the...Ch. 14 - 14.42 A steel wide-flange beam is oriented so that...Ch. 14 - A W1045steel wide-flange beam supports a uniformly...Ch. 14 - 14.44 A steel wide-flange section is subjected to...Ch. 14 - A W30108 steel wide-flange beam is simply...Ch. 14 - A W612 is strengthened with a 34 -in.-by- 34 -in....Ch. 14 - Four wood boards 1 in. by 6 in. in cross section...Ch. 14 - A lintel consists of two 8 -in.-by- 12 in. steel...Ch. 14 - A 50 -mm-by- 300 -mm scaffold timber plank, placed...Ch. 14 - A laminated wood beam is built up by gluing...Ch. 14 - A rectangular hollow shape carries loads as shown....Ch. 14 - For the beam shown, calculate the maximum tensile...Ch. 14 - 14.53 A box beam is built up of four -in.-by--in....Ch. 14 - 14.54 Find the value of the loads P that can be...Ch. 14 - 14.55 Solve Problem 14.54 assuming that the timber...Ch. 14 - Calculate the values of S and Z and the shape...Ch. 14 - 14.57 A is supported on simple supports on a -ft...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- EXAMPLE No. 2 The laminated beam shown supports a uniform load of 12 kN/m. If the beam is to have a height to width ratio of 1.5, determine the smallest width. Gallow-9 MPa, tallew = 0.6 MPa. Neglect the weight of the beam. 12 kN/m B 1.5b A 3 m 1marrow_forward8. A steel beam of uniform cross-section is 6.5 m long and weighs 300 N/rn of length. There are two supports spaced 5 m apart, one of which is located at the end of the beam. Calculate the load required on the free end to just balance the weight of the beamarrow_forwardThe beam shown will be constructed from a standard steel W-shape using an allowable bending stress of 40.4 ksi. Assume P = 51 kips, L1=6.6 ft, and L2=19.8 ft. (a) Determine the minimum section modulus required for this beam. (b) From the table below, select the lightest W shape that can be used for this beam. (c) What is the total weight of the steel beam itself (i.e., not including the loads that are carried by the beam)?arrow_forward
- . For the beam shown, calculate (a) the maximum bending stress; and (b) the bending stress at a point 0.75 in from the top of the beam at section 5 ft from left end of the beam. 2000 lb 3000 lb 2 in 3 ft 4 ft 1 ft 5 in 5 ft Figure 5.5.4arrow_forwardHelp me plsarrow_forwardFigure 14.20 Full Alternative Text 14.21 A solid rectangular simply supported timber beam 6 in. wide, 20 in. deep, and 10 ft long carries a concentrated load of 16,000 lb at midspan. Use nominal dimensions. a. Compute the maximum horizontal shear stress at the neutral axis. b. Compute the shear stress 4 in. and 8 in. above and below the neutral axis. Neglect the weight of the beam.arrow_forward
- Floor joists 64.8 mm wide by 106 mm high, simply supported on a 4.3 m span, carry a floor loaded at 5.1 kPa. Compute the center-line spacing between joists in meters to develop a bending stress of 10.9 MPa.arrow_forwardDerive the formula for the bending stress of a beam with a rectangular cross section and triangular cross secrion. Thank youarrow_forwardA simply supported beam 10 m long has an overhang of 1.1 m at the left support. If a highway uniform load of 12.02 kN/m and a concentrated load of 194 kN, passes thru the beam, compute the maximum positive shear (kN) based on influence line for maximum shear at mid span.arrow_forward
- Situation 2 | Beam ABCDEFG below is subjected to multiple loads as show. The total length of the beam is 10m. Analyze the beam completely. 6 kN 10 kN 3 kN/m 2 kN 5 kN-m G 3000mm. 1000mm 1000mm. 2000mm. 1000mm 2000mm.arrow_forwardA uniform wind load of q = 0.2 kN/m? acts on the billboard with dimensions of b = 1.5 m and a = 1 m. The allowable normal stress is oalow = 140 MPa, c = 0.5 m for the circular cross section panel pole. Draw the shear force, bending moment and torsional moment diagrams for the panel pole. a) Calculate the cross-section diameter d, using the maximum shear stress (Tresca) criterion. b) Calculate the cross-section diameter d, using the maximum distortional energy (von Mises) criterion. SOLUTION kesitarrow_forward2. A simply supported rectangular concrete beam of span 8m has to be prestressed with a force of 1600 kN. The tendon is of parabolic profile having zero eccentricity at the supports. The beam has to carry an external uniformly distributed load of intensity 30 kN/m. Neglecting the self- weight of the beam, the maximum dip (in meters, up to two decimal places) of the tendon at the mid-span to balance the external load should be? Span of the beam, L = 8m Prestressing force, P = 1600 kN %3D U.D.L. on the beam, w = 30 kN/m Maximum dip of tendon to balance the external load e = ?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Solids: Lesson 53 - Slope and Deflection of Beams Intro; Author: Jeff Hanson;https://www.youtube.com/watch?v=I7lTq68JRmY;License: Standard YouTube License, CC-BY