INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
14th Edition
ISBN: 9780133918922
Author: Russell C. Hibbeler
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5.4, Problem 26P
The mobile crane is symmetrically supported by two outriggers at A and two at B in order to relieve the suspension of the truck upon which it rests and to provide greater stability. If the crane boom and truck have a mass of 18 Mg and center of mass at G1, and the boom has a mass of 1.8 Mg and a center of mass at G2, determine the vertical reactions at each of the four outriggers as a function of the boom angle θ when the boom is supporting a load having a mass of 1.2 Mg. Plot the results measured from θ = 0° to the critical angle where tipping starts to occur.
Expert Solution & Answer
Learn your wayIncludes step-by-step video
schedule09:09
Students have asked these similar questions
4 of 4
5-67. Due to an unequal distribution of fuel in the wing
tanks, the centers of gravity for the airplane fuselage A
and wings B and C are located as shown. If these
components have weights WA = 45 000 lb, WR = 8000 lb,
and Wc = 6000 lb, determine the normal reactions of the
wheels D, E, and F on the ground.
8 ft
4 ft
6 ft
8 ft
6 ft
20 ft
3 ft
4 of
5-67. Due to an unequal distribution of fuel in the wing
tanks, the centers of gravity for the airplane fuselage A
and wings B and C are located as shown. If these
components have weights WA = 45 000 lb, Wg = 8000 lb,
and Wc = 6000 lb, determine the normal reactions of the
wheels D, E, and F on the ground.
B.
8 ft
4 ft
6 ft
8 ft
6 ft
20 ft
3 ft
The jib crane is designed for a maximum capacity of 9 kN, and its uniform I-beam has a mass of 260 kg. Plot the magnitude R of the
force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.4 m. On the same set of axes, plot the x- and y-
components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as
a check for your work.
(a) What is the value of R when x = 1.6 m?
(b) What is the value of R when x = 3.2 m?
(c) Determine the minimum value of R and the corresponding value of x.
(d) For what value of R should the pin at A be designed?
32°
x
m
9 KN
1.0 m
2.6 m
Questions:
(a) If x= 1.6 m, R=
i
(b) If x= 3.2 m, R = i
(c) The minimum value for R = i
(d) The pin should be designed to hold
i
KN
KN
kN at x =
i
kN.
Chapter 5 Solutions
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Ch. 5.2 - Draw the free-body diagram for the following...Ch. 5.2 - Draw the free-body diagram for the following...Ch. 5.2 - Draw the free-body diagram for the following...Ch. 5.2 - Draw the free-body diagram for the following...Ch. 5.2 - Draw the free-body diagram for the following...Ch. 5.2 - Draw the free-body diagram for the following...Ch. 5.2 - Draw the free-body diagram for the following...Ch. 5.2 - Draw the free-body diagram for the following...Ch. 5.2 - Draw the free-body diagram for the following...Ch. 5.4 - Draw the free body diagram of each object. Prob....
Ch. 5.4 - Determine the horizontal and vertical components...Ch. 5.4 - Determine the horizontal and vertical components...Ch. 5.4 - The truss is supported by a pin at A and a roller...Ch. 5.4 - Determine the components of reaction at the fixed...Ch. 5.4 - The 25 kg bar has a center of mass at G. If it is...Ch. 5.4 - Determine the reactions at the smooth contact...Ch. 5.4 - Determine the components of the support reactions...Ch. 5.4 - Determine the reactions at the supports. Prob....Ch. 5.4 - Determine the horizontal and vertical components...Ch. 5.4 - Determine the reactions at the supports. Prob....Ch. 5.4 - Determine the reactions at the supports. Prob....Ch. 5.4 - Determine the reactions at the supports. Prob....Ch. 5.4 - Determine the tension in the cable and the...Ch. 5.4 - The man attempts to a up port the toad of boards...Ch. 5.4 - Determine the components of reaction at the...Ch. 5.4 - The man has a weight W and stands at the center of...Ch. 5.4 - A uniform glass rod having a length L is placed in...Ch. 5.4 - The uniform rod AB has a mass of 40 kg. Determine...Ch. 5.4 - If the intensity of the distributed load acting on...Ch. 5.4 - If the roller at A and the pin at B can support a...Ch. 5.4 - The relay regulates voltage and current. Determine...Ch. 5.4 - Determine the reactions on the bent rod which is...Ch. 5.4 - The mobile crane is symmetrically supported by two...Ch. 5.4 - Determine the reactions acting on the smooth...Ch. 5.4 - A linear torsional spring deforms such that an...Ch. 5.4 - Determine the force P needed to pull the 50-kg...Ch. 5.4 - Determine the magnitude and direction of the...Ch. 5.4 - The operation of the fuel pump for an automobile...Ch. 5.4 - Determine the magnitude of force at the pin A and...Ch. 5.4 - The dimensions of a jib crane, which is...Ch. 5.4 - The dimensions of a jib crane, which is...Ch. 5.4 - The smooth pipe rests against the opening at the...Ch. 5.4 - The beam of negligible weight is supported...Ch. 5.4 - The cantilevered jib crane is used to support the...Ch. 5.4 - The cantilevered jib crane is used to support the...Ch. 5.4 - The bar of negligible weight is supported by two...Ch. 5.4 - Determine the stiffness k of each spring so that...Ch. 5.4 - The bulk head AD Is subjected to both water and...Ch. 5.4 - The boom supports the two vertical loads. Neglect...Ch. 5.4 - The boom is intended to support two vertical loads...Ch. 5.4 - The 10-kg uniform rod is pinned at end A. If It is...Ch. 5.4 - If the truck and its contents have a mass of 50 kg...Ch. 5.4 - Three uniform books each having a weight W and...Ch. 5.4 - Determine the reactions at the pin A and the...Ch. 5.4 - If rope BC will fail when the tension becomes 50...Ch. 5.4 - The rigid metal strip of negligible weight is used...Ch. 5.4 - The rigid metal strip of negligible weight is used...Ch. 5.4 - The cantilever footing is used to support a wail...Ch. 5.4 - The uniform beam has a weight Wand length l and is...Ch. 5.4 - A boy stands out at the end of the diving board,...Ch. 5.4 - The 30-N uniform rod has a length of l = 1 m. If s...Ch. 5.4 - The uniform rod has a length I and weight W. It is...Ch. 5.4 - I he uniform rod of length L and weight W is...Ch. 5.4 - Assuming that the foundation exerts a linearly...Ch. 5.4 - Assuming that the foundation exerts a linearly...Ch. 5.4 - If it is also subjected to a couple moment of 100...Ch. 5.4 - Determine the distance d for placement of the load...Ch. 5.4 - If d = 1 m, and = 30, determine me normal...Ch. 5.4 - The man attempts to pull the tour wheeler up the...Ch. 5.4 - Where is the best place to arrange most of the...Ch. 5.7 - Draw the free-body diagram of each object.Ch. 5.7 - In each case, write the moment equations about the...Ch. 5.7 - The uniform plate has a weight of 500 lb....Ch. 5.7 - Determine the reactions at the roller support A,...Ch. 5.7 - The rod is supported by smooth journal bearings at...Ch. 5.7 - Determine the support reactions at the smooth...Ch. 5.7 - Determine the force developed in the short link...Ch. 5.7 - Determine the components of reaction that the...Ch. 5.7 - Determine the tension each rope and the force that...Ch. 5.7 - If these components have weights WA = 45000 Wa =...Ch. 5.7 - Determine the components of reaction at the fixed...Ch. 5.7 - Determine the vertical reactions at the wheels C...Ch. 5.7 - Determine the components of reaction at A, the...Ch. 5.7 - Determine the tension in each of the three...Ch. 5.7 - Determine the components of reaction at hinges A...Ch. 5.7 - Determine me tension in each cable and the...Ch. 5.7 - The cables are attached to a smooth collar ring at...Ch. 5.7 - Determine the components of reaction at the...Ch. 5.7 - Determine the components of reaction at the...Ch. 5.7 - Determine the components of reaction at the...Ch. 5.7 - Determine the magnitude of F which will cause the...Ch. 5.7 - Determine the components of reaction at A and the...Ch. 5.7 - Determine the components of reaction at these...Ch. 5.7 - Determine the components or reaction at these...Ch. 5.7 - Compute the x, y, z components of reaction at the...Ch. 5.7 - Determine the magnitude of F2 which will cause the...Ch. 5.7 - At A the connection is with a ball-and-socket....Ch. 5.7 - If it is supported by a ball-and-socket joint at C...Ch. 5.7 - Determine the x, y, z components of reaction at...Ch. 5.7 - Determine the horizontal tension T in the belt on...Ch. 5.7 - Determine the horizontal tension T in the belt on...Ch. 5.7 - Determine the components of reaction at A and the...Ch. 5.7 - If the roller at 8 can sustain a maximum load of 3...Ch. 5.7 - Determine the reactions at the supports A and B...Ch. 5.7 - Determine the normal reaction at the roller A and...Ch. 5.7 - Determine the horizontal and vertical components...Ch. 5.7 - Determine the x, y, z components of reaction at...Ch. 5.7 - Determine the horizontal equilibrium force P that...Ch. 5.7 - Determine the x, y, z components of reaction at...Ch. 5.7 - Determine the x and z components of reaction at...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
3.58 The transmission tower shown is subjected to a horizontal wind force of 400 lb acting at point B. Support ...
Applied Statics and Strength of Materials (6th Edition)
Determine the slope and deflection of end A of the cantilevered beam. E = 200 GPa and I = 65.0(106) mm4. F122
Mechanics of Materials (10th Edition)
The friction force at the surface of contact (F).
Engineering Mechanics: Statics & Dynamics (14th Edition)
Determine the slope and deflection of end A of the cantilevered beam. E = 200 GPa and I = 65.0(106) mm4. F122
Mechanics of Materials
When 2000 L/min of water flows through a circular section with an inside diameter of 300 mm that later reduces ...
Applied Fluid Mechanics (7th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?arrow_forwardThe jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 230 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 2.0 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 34° x 1.3 m 6 kN -2.9 marrow_forwardThe jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.9 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 2.4 m? (b) What is the value of R when x = 4.5 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 1.6 m Questions: 25° 14 KN -3.5 m (a) If x = 2.4 m, R = (b) If x= 4.5 m, R= (c) The minimum value for R = i (d) The pin should be designed to hold i KN KN kN at x = i kN. marrow_forward
- The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)arrow_forwardThe jib crane is designed for a maximum capacity of 5 kN, and its uniform I-beam has a mass of 200 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.9 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 0.8 m? (b) What is the value of R when x = 3.2 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 40° m 5 KN -2.9 m 1.2 m Questions: (a) If x = 0.8 m, R= (b) If x= 3.2 m, R= i (c) The minimum value for R = i (d) The pin should be designed to hold i kN kN kN at x = kN.arrow_forwardThe overhanging beam is supported by a pin at A and the two-force strut BC Determine the horizontal and vertical components of reaction at A. Determine the magnitude of the reaction at B on the beam.arrow_forward
- Because of long-term loading from the 900-N tension in the power line, the uniform utility pole has developed a 5° lean. If the mass per unit length of the 9-m pole is 24 kg/m and the mass of the lamp fixture is negligible, determine the reactions at the ground support A. (Moment of Force, Forces along x and Forces along y)arrow_forwardThe ramp is used as passengers board a small commuter airplane. The total mass of the ramp and six passengers is 730 kg with a mass center at G. Determine the force in the hydraulic cylinder AB (positive if in tension, negative if in compression) and the magnitude of the pin reaction at C.arrow_forwardThe bent rod is supported at A, B, and C by smooth journal bearings. The rod is subjected to the force F = 620 N . The bearings are in proper alignment and exert only force reactions on the rod. Determine the components of reaction at the bearing AA using scalar notation. Determine the components of reaction at the bearing BB using scalar notation. Determine the components of reaction at the bearing CC using scalar notation.arrow_forward
- Determine the magnitude and direction with respect to the +x-axis on the reaction at A and at C. Note that the body is supported by pin at A and a roller at C. The bodys weight is negligible.arrow_forwardThe smooth disks D and E have a weight of 220 lb and 100 lb, respectively. If a horizontal force of P = 220 lb is applied to the center of disk E, determine the normal reactions at the points of contact with the ground at A, B, and C.arrow_forwardDraw the free-body diagram of the uniform bar, which has a mass of 100 kg and a center of mass at G. The supports A, B, and C are smooth.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Mechanical SPRING DESIGN Strategy and Restrictions in Under 15 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=dsWQrzfQt3s;License: Standard Youtube License