Calculate the voltage gain, current gain, input impedance, and output impedance for the transistor network shown in Figure 19.132 in the textbook.
Answer to Problem 93P
The voltage gain, current gain, input impedance, and output impedance for the transistor network are
Explanation of Solution
Given Data:
Refer to Figure 19.132 in the textbook for the transistor network circuit.
From the given transistor network circuit, the internal resistance
Formula used:
Refer to Equation 19.73 in the textbook and write the expression for voltage gain of a transistor network in terms of hybrid parameters as follows:
Here,
Write the expression for current gain of the transistor network as follows:
Here,
Write the expression for input impedance of the transistor network as follows:
Calculation:
Redraw the given circuit as shown in Figure 1.
From Figure 1, write the expression for emitter current as follows:
Write the expression for base voltage from the circuit in Figure 1 as follows:
Write the expression for collector current as follows:
Write the expression for collector voltage as follows:
From Equation (7), substitute
Rearrange the expression as follows:
From Equation (2), substitute
Substitute 150 for
From Equation (6), substitute
Rearrange the expression as follows:
Rearrange the expression in Equation (5) as follows:
From Equations (7) and (9), substitute
Rearrange the expression as follows:
Substitute 150 for
Simplify the expression as follows:
From Equation (1), substitute
From Equation (9), substitute
Rearrange the expression as follows:
Substitute 150 for
From Equation (3), substitute
Consider output voltage
Apply KVL to the input loop for the circuit in Figure 2 as follows:
Substitute 1 for
Apply KCL at the output node for the circuit in Figure 2 as follows:
Substitute 1 for
Rearrange the expression as follows:
From Equation (12), substitute
Substitute 150 for
Write the expression for output impedance of the transistor network as follows:
Substitute 1 for
Conclusion:
Thus, the voltage gain, current gain, input impedance, and output impedance for the transistor network are
Want to see more full solutions like this?
Chapter 19 Solutions
Fundamentals of Electric Circuits
- Find H parameters for the circuit 82 ww 62 ww oww 42 42arrow_forwardSketch ir and vo for the network below for the input shown. 10 k2 10 V Si 5.3 V 7.3 V - -10 Varrow_forward(1I) Determine the magnitudes and directions of the currents through R, and R, in Fig. 19 R1 R2 59. V=9.0 V R=220 R2= 18 2 V3=6.0 V FIGURE 19-59arrow_forward
- 2. Find the hybrid parameters of the following circuit. 1 F V1 1 FZ 1 Ω 1 F 201 1Ω· 02arrow_forwardFor the phase-shift oscillator, determine the feedback resistor required to produce an oscillator frequency of 7.2 kHz if all the resistors in the 3 RC networks are 12.5 kΩ.arrow_forwardFind the hybrid integers in a two-port network. (e-1 (rad/sec)) mm 04H V₁ à ₁ (2) 211 ₁24 AM 18 12 2.5F HH I V₂arrow_forward
- 2. (a) Overlay error is checked at the top, bottom, left and right edges, and center of a 4-inch Si wafer. The observed errors in x and y (in um) are found to be: um T. L. B 0.3 0.0 0.0 0.7 0.5 1.0 y 0.7 1.0 0.5 0.3 Analyze the error in/out, rotational and translational misalignment (b) Discuss the advantage and disadvantage of a projection lithography process.arrow_forwardFor the common-base network, determine the following: (a) Rc (b) IB (c) IE (d) VBC (e) VCE 14 V Vc=8V 4 Vo Rc RE H V₂ B=90 HoVi HH *1.1 ΚΩarrow_forwardA Cúk converter input voltage is 200V and output of 50V, the switching frequency is 10kHz, the input and output inductances L1 and L2 value is 200puH and input and output capacitors C1 and C2 are 500µF. Load resistance is 50. The average value of the input inductor (L1) voltage is: İLi, + ¢L C, ia L2 "a本 va Load V V, Vam VT Go Soloct ono:arrow_forward
- 5 ohms j5 ohms a 3 ohms 10 /0° volts Zth j4 ohms Figure 19.4 Using Thevenin's theorem, what should be the value of ZTh for the circuit shown in Figure 19.4?arrow_forwardA transistor is used as a switch and the waveforms are shown below. The parameters are given as follows: Vcc = 150 V, VBE(sat) = 5 V, Igs = 10 A, VCE(sat) = 2 V, Ics = 120 A, ta = 0.5 us, t, = 1 us, ts = 2 us, tf = 2 us and f =10 KHz, k = 50 % and ICEO = 1 mA. The conduction time t, and the blocking time t, are equal to: VCE Vcc VCE(s31) ton toff Ics ICEO ig Select one: O a. 46 µs, 48 us O b. 20 us, 45 µs O C. 48.5 us, 46 µs o d. 45 µs, 20 µsarrow_forwardDetermine Z. Transfurim including reyina of Cunvergence Int Xcn)= )arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,