EBK MANUFACTURING PROCESSES FOR ENGINEE
6th Edition
ISBN: 9780134425115
Author: Schmid
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 2, Problem 2.69P
To determine
The length to which the bar should be stretched so that it will be straight after unloading.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A steel bar of 50mm wide, 12mm thick and
300mm long is subjected to an axial pull of
84KN. Find the changes in length, width,
thickness and volume of the bar. Take E = 2
x 105 N/mm2 and Poisson's ratio = 0.32
%3D
A steel bar 50 mm wide, 12mm thick and 300 mm long is subjected to an axial pull of 84 kN. Find the changes in the length, width, thickness and the volume of the bar. Take E = 200 GPa and Poisson's ratio= 0.32
δt = 0.0027mm (decrease), δV = 45.36mm³ (increase)]
A 100 mm x 100 mm x 100 mm cube made with glass polymers in the y-
direction is subjected to a tensile load of 100 kN along the y-direction. However,
the cube is constrained against deformation in the x and z directions. Given the
following properties:
Ex = 20 GPa
Ey = 50 GPa
Ez = 20 GPa
vxy = 0.25
vxz = 0.5
vyz = 0.25
(a) Compute for the change in length of the cube in the y-direction and;
(b) Determine the stresses, σx, σy, σz
Chapter 2 Solutions
EBK MANUFACTURING PROCESSES FOR ENGINEE
Ch. 2 - Prob. 2.1QCh. 2 - Prob. 2.2QCh. 2 - Prob. 2.3QCh. 2 - Prob. 2.4QCh. 2 - Prob. 2.5QCh. 2 - Prob. 2.6QCh. 2 - Prob. 2.7QCh. 2 - Prob. 2.8QCh. 2 - Prob. 2.9QCh. 2 - Prob. 2.10Q
Ch. 2 - Prob. 2.11QCh. 2 - Prob. 2.12QCh. 2 - Prob. 2.13QCh. 2 - Prob. 2.14QCh. 2 - Prob. 2.15QCh. 2 - Prob. 2.16QCh. 2 - Prob. 2.17QCh. 2 - Prob. 2.18QCh. 2 - Prob. 2.19QCh. 2 - Prob. 2.20QCh. 2 - Prob. 2.21QCh. 2 - Prob. 2.22QCh. 2 - Prob. 2.23QCh. 2 - Prob. 2.24QCh. 2 - Prob. 2.25QCh. 2 - Prob. 2.26QCh. 2 - Prob. 2.27QCh. 2 - Prob. 2.28QCh. 2 - Prob. 2.29QCh. 2 - Prob. 2.30QCh. 2 - Prob. 2.31QCh. 2 - Prob. 2.32QCh. 2 - Prob. 2.33QCh. 2 - Prob. 2.34QCh. 2 - Prob. 2.35QCh. 2 - Prob. 2.36QCh. 2 - Prob. 2.37QCh. 2 - Prob. 2.38QCh. 2 - Prob. 2.39QCh. 2 - Prob. 2.40QCh. 2 - Prob. 2.41QCh. 2 - Prob. 2.42QCh. 2 - Prob. 2.43QCh. 2 - Prob. 2.44QCh. 2 - Prob. 2.45QCh. 2 - Prob. 2.46QCh. 2 - Prob. 2.47QCh. 2 - Prob. 2.48QCh. 2 - Prob. 2.49PCh. 2 - Prob. 2.50PCh. 2 - Prob. 2.51PCh. 2 - Prob. 2.52PCh. 2 - Prob. 2.53PCh. 2 - Prob. 2.54PCh. 2 - Prob. 2.55PCh. 2 - Prob. 2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - Prob. 2.59PCh. 2 - Prob. 2.60PCh. 2 - Prob. 2.61PCh. 2 - Prob. 2.62PCh. 2 - Prob. 2.63PCh. 2 - Prob. 2.64PCh. 2 - Prob. 2.65PCh. 2 - Prob. 2.66PCh. 2 - Prob. 2.67PCh. 2 - Prob. 2.68PCh. 2 - Prob. 2.69PCh. 2 - Prob. 2.70PCh. 2 - Prob. 2.71PCh. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Prob. 2.74PCh. 2 - Prob. 2.75PCh. 2 - Prob. 2.76PCh. 2 - Prob. 2.78PCh. 2 - Prob. 2.79PCh. 2 - Prob. 2.80PCh. 2 - Prob. 2.81PCh. 2 - Prob. 2.82PCh. 2 - Prob. 2.83PCh. 2 - Prob. 2.84PCh. 2 - Prob. 2.85PCh. 2 - Prob. 2.86PCh. 2 - Prob. 2.87PCh. 2 - Prob. 2.88PCh. 2 - Prob. 2.89PCh. 2 - Prob. 2.90PCh. 2 - Prob. 2.91PCh. 2 - Prob. 2.92PCh. 2 - Prob. 2.93PCh. 2 - Prob. 2.94PCh. 2 - Prob. 2.95PCh. 2 - Prob. 2.96PCh. 2 - Prob. 2.97PCh. 2 - Prob. 2.98PCh. 2 - Prob. 2.99PCh. 2 - Prob. 2.100PCh. 2 - Prob. 2.101P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- (a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressurearrow_forwardA plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of the bars is 80. If the allowable shear strain in the plastic is 0.014 radian, what is the minimum permissible length of the bar in mm?arrow_forwardLet's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. When a tensile force F is subjected to that rod cross-section, the diameter becomes 3.995 mm. Determine the applied force F. Consider a linear elastic behavior.arrow_forward
- A solid cylindrical rod 12 mm in diameter and 50 mm in length is attached to a rigid support at one end and twisted at its free end by 14°. If the Poisson’s ratio for this isotropic material is 0.34 and Young’s modulus is 70 GPa, what is the maximum shear stress induced?arrow_forwardThe bulk modulus of the steel bar with modulus of elasticity 1.8x105N/mm2 and Poisson’s ratio 0.25 isarrow_forwardWhen a brass rod of diameter 2 mm is subjected to a tension of Sx10 N, the diameter changes by 3.6x104 cm. Calculate the Poisson's ratio for brass given that the Elastic modulus for the brass is 9x100 N/m and the longitudinal strain for the brass rod is1.96x103 useful equation: Poissons ratio = Lateral strain / Longitudinal strain O 0.63 O 031 O 1.11 O 0,92arrow_forward
- A tensile stress is to be applied along the axis of a cylindrical brass rod with diameter of 200 mm. What is the load magnitude required to produce 2.8 x 10^-2 change in diameter if the deformation is entirely elastic?arrow_forwardA bar of 12 mm diameter gets stretched by 3mm under a steady load of 8000 N. What stress would be produced in the bar by a weight of 800 N which falls through 8 cm before commencing the stretching of the bar which is initially unstressed. Take E= 2 × 105 N/mm2arrow_forwardCalculate the modulus of rigidity and bulk modulus of a cylindrical bar of diameter of 25 mm and of length 1.6 m, if the longitudinal strain in a bar during a tensile test is four times the lateral strain. Find the change in volume, when the bar is subjected to a hydrostatic pressure of 100 N/mm?. Take E = 1 x 105 N/mm?.arrow_forward
- A rubber ball is inflated to a pressure of 60KPa. At that pressure, the diameter of the ball is 230mm and the wall thickness is 1.2mm. The rubber has a modulus of elasticity of E = 3.5MPa and Poisson’s ratio of 0.45. (a)Compute the maximum tensile stress. (b)If the allowable tensile stress of the rubber ball wall is 2.5MPa, compute the internal pressure the rubber ball could be inflated.arrow_forward2. A thin steel tire is shrunk on to a locomotive wheel of 1.2 m diameter. Find the internal diameter of the tire if after shrinking on, the hoop stress in the tire is 100 MPa. Assume E=200kN/mm2. Also find the least temperature to which the tire must be heated above that of the wheel before it could be slipped on. The coefficient of linear expansion for the tire is 6.5×10–6 per °C.arrow_forwardThe Young's modulus of a material is 125 GPa and Poisson's ratio is 0.25. The modulus of rigidity of the material isarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY