Answered: Determine the shear resistance of a…

Determine the shear resistance of a rolled channel section 229 x 89 Grade S275 steel loaded parallel to the web. Design shear force is 50KN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

FOR THE GIVEN PROPERTIES DESIGN d': 15 mm THE REINFORCEMENT OF : 400 mm b d = $80 mm fc = 33 MPa fy = 320 MPa Mu: 1 000 000 000 N mm A. USE B.USE OF NSCP 2001 NSCP 2015 BEAM THE BEAM 132 13 Gra mm of BELOW. #H 1606 210135 03 M 12437 P0122399/100mA 02338941 242
PROBLEMS: 1. The bolt connection shows 8-22mm diameter bolts in a bolt hole diameter of 25 mm and spaced according to the following: Sı = 40mm T = 16mm S2 = 80mm S3 = 50mm S4 = 100mm te = 12mm Determine the force T if the allowable tensile stress is 200 MPa, the allowable bolt shear stress is 120MPa and the allowable plate bearing stress is 120 MPa. 2. A long retaining wall is braced by wood shores set at ang angle of 30° and supported by concrete thrust blocks as shown. The shores are evenly spaced, 3m apart. For analysis purposes, the wall and shores are idealized on the second image. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall I assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the wall is F= 190KN. If each shore has a 150mmx150mm square cross section, what is the compressive stress in the shores? Retaining wall Soil Concrete Shore thrust block 30 30 1,5 m…
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee A w24 X55 is used as a beam with a length of 6m. The beam is supported by a bearing plate of 300 mm x 200 mm x 30 mm on the wall having a thickness of 250 mm.Properties: d=598.68mmbf = 177.93 mmtw =10.03mm k=33.34 mmtf = 12.83mmFy = 250 MPaQuestions:1. Determine the design strength for web local yielding.2. Determine the design strength for web crippling.
Steel Design Given: S = 2m L = 10m Superimposed dead load = 5 kPa Live load = 3.6 kPa Properties of Beam BFA section = W 460 x 97 kg/mArea (A) = 12320 mm^2Depth (d) = 465 mmFlange Width (bf) = 193 mmFlange Thickness (tf) = 19mmWeb Thickness (tw) = 11 mm Moment of InertiaIx = 445 x 10^6 mm^4Iy = 23 x 10^6 mm^4Yield Strength, Fy = 248 MPar (radius of gyration of a section compromising the compression flange plus 1/3 of the compression web area of compression flange = 50 mm. Consider bending about the x-axis. 1. The compression flanges are laterally supported only at midspan. With this condition, what is the permissible flexural stress if Cb = 1.0?
Two plates are connected by 16-mm bolts in as shown in the figure. Compute the maximum shear stress of each bolt if F = 100 KN. F F 500 mmm W 500 mmm 200 mmm F 50 mm
Use AISC Equation E3-2 or E3-3 and determine the axial compressive strength oP for the following cases: a. L = 15 ft 233.1 kips 159 kips 26.65 kips O 259 kips L W10 x 33 A992 steel
Two plates are connected using three 20-mm-diameter bolts as shown in the figure. If the axial load P is 50 kN determine the shear stress in each bolt. 130 mm 25 mm Your answer: O 53 MPa. O 159 MPa O26.5 MPa O 79.5 MPa O 106 MPa: ooo 25 mm P
The cross-sectional area of an aluminum bar is 170 mm?. It carries an axial loads at the positions as shown in the figure. Compute the total deformation of the bar if E = 80 Gpa. Assume the bar is suitably braced to prevent buckling. Add "9" in the loads only. Example: 40+9=49, 18+9=27, 42+9=51, 20+9=29 Area = 170mm' 2 40KN 18KN 20KN 42KN 1.0m 1.80m 0.70m
12. Refer to figure 6. The 20-mm-diameter bolt fastens two wooden planks together. The nut is tightened until the tensile stress in the bolt is 150 MPa. Find the smallest safe diameter d of the washers if the working bearing stress for wood is 13 MPa. = 20 mm a. 70.8 mm b. 75.2 mm c. 86.3 mm d. 80.5 mm e. none of the above FIGURE 6
SITUATION 14: A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25 mm Ø rivets as shown in the figure. The rivet holes have a diameter 2 mm larger than the rivet diameter. The plate is A36 steel with Fy= 250 MPa, allowable tensile stress of 0.60Fy and allowable bearing stress of 1.35Fy. The rivets are A502, Grade 2, hotdriven rivets with allowable shear stress of 150 MPa. 25 mm Ø rivets + + PL 300x20 P/2 P P/2 PL 300x10 43. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable shear stress in the rivets? a. 675 KN b. 490 KN c. 598 KN d. 790.5 kN 44. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable bearing stress between the plates and the rivets? a. 490 KN b. 675 KN c. 598 KN d. 790.5 kN 45. Which of the following most nearly gives the max. load in kN that can be applied to the…
6. Give the properties table below. A992 Steel 7178 T76 Aluminum Yield Strength 50 ksi 73 ksi Ultimate strength 75 ksi 85 ksi Modulus of Elasticity 29,000 ksi 10,500 ksi Assume you are designing a rectangular member with a specific allowed height. For a design where deflection criterion controls which material would require a larger cross section? For a design where tension stress controls, which material requires the larger cross section?
A steel flat of rectangular section of size 70 x 6 mm is connected to a gusset plate by three bolts each having a shear capacity of 15kN in holes having diameter 11.5mm. If the allowable tensile stress in the flat is 150MPa, the maximum tension that can be applied to the flat is T4 35 15 1221 5885 20 20 15