A steel flat of rectangular section of size 70 x 6 mm is connected to a gusset plate by three bolts each having a shear capacity of 15kN in holes having diameter 11.5mm. If the allowable tensile stress in the flat is 150MPa, the maximum tension that can be applied to the flat is 35 15 1221 5505 20 20 15

A steel flat of rectangular section of size 70 x 6 mm is connected to a gusset plate by three bolts each having a shear capacity of 15kN in holes having diameter 11.5mm. If the allowable tensile stress in the flat is 150MPa, the maximum tension that can be applied to the flat is 35 15 1221 5505 20 20 15

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. Use a501 plate and a502 gr2 rivet a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
I Example 2 W SECTION The hanger below (front view and side view) supports a 5000 N partition wall. Calculate the normal stress in the angles if they are 76 x 76 mm with a thickness of 9.5 mm. Calculate the shear stress in the bolts, the bearing stress on the gusset plate and on the angles. PL120X10 220 A325M BOLTS 2- L76x76x9.5 T, O O O O
ll zain IQ 37 MPa no one 10/10 find the tensile stress in upper plate in section 3-3 5 1 4 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80 kN B-bolt DIA. 10 MM 10 MPa 12.5 MPa 15 MPa 8.5 MPa no one 10/ find the bearing stress between bolts and plate
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
ZAO O "l zain IQ docs.google.com/forms O 0/10 find the tensile stress in upper plate in section 1-1 5 1 4 80 kN 80 kN Q B-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 30 MРа 33 МРа 35 MPа 37 MPa no one 10/10 find the tensile stress in upper plate in section 3-3 +
A76 x 76 x6 mm angular section shown is welded to an 8 mm thick gusset plate. The length L1 is 65 mm, L2 is 125 mm, and the cross sectional area of the angle is 929 sq.mm. Fy-248MPA and Fu -400MPA. Gusset Plate Alowable Sresse Alowable tensle stress igross ara)0.00 Alowable tereile stres net area)0SOF. Allowable shear stress (net ares)0.30F. Determine the value of P based on net area using a strength reduction coefficient of 85% O 138.24 KN O 140.14 kN O 157.93 kN O 304.00 N Next
What is the axial stress in the bronze rod (in MPa)? 2m 3m 6o kN mm 15mm banzerod
A 2 - inch hole ic to be punchicd on a 3/8-inch thick plate with an ultimate chearing strergth of 42 ksi. KWhat should be the minimum the puncher.? compressive strength of
REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P = 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Peso 100 m
A flanged bolt coupling consists of 9-16-mm-diameter steel bolts on a bolt circle 400 mm in diameter, and 5-16-mm-diameter steel bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 68 MPa in the bolts? Answer must be in kN-m. « Previous Next » Not saved Submit Quiz ENG US