The cross-sectional area of an aluminum bar is 170 mm?. It carries an axial loads at the positions as shown in the figure. Compute the total deformation of the bar if E = 80 Gpa. Assume the bar is suitably braced to prevent buckling. Add "9" in the loads only. Example: 40+9=49, 18+9=27, 42+9=51, 20+9=29 Area = 170mm' 40KN 18KN 42KN 20KN 1.0m 1.80m 0.70m

The cross-sectional area of an aluminum bar is 170 mm?. It carries an axial loads at the positions as shown in the figure. Compute the total deformation of the bar if E = 80 Gpa. Assume the bar is suitably braced to prevent buckling. Add "9" in the loads only. Example: 40+9=49, 18+9=27, 42+9=51, 20+9=29 Area = 170mm' 40KN 18KN 42KN 20KN 1.0m 1.80m 0.70m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of its length and diam- eter d, = 12 mm over the other half (see figure part a). The modulus of elasticity is E = 205 GPa. (a) How much will the bar elongate under a tensile %3D %3D load P = 22 kN?
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
Determine the following: Displacement of B (in mm) with respect to A. Displacement of C (in mm) with respect to A. Principal stresses at point O, if it is 200mm from C. (unit should be kPa). A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Calculate the axial deformation of the Brass cylinder section (BC) shown in Figure 8. The cross-sectional areas are Asteel = 80 x 10-³ m² and ABrass = 50 x 10-³ m², and Young's modulus - of steel and brass are 200 MPa and 120 MPa. 100 kN (a) 3.13 mm (b) 7.25 mm (c) 7.5 mm (d) 3.5 mm Steel 50 kN 0.5 m B Brass 0.3 m C Figure 8. A shaft of different diameters Steel 0.5 m Ꭰ 150 kN
The compound bar ABCD has a uniform cross-sectional area of 0.25 in.² When the axial force P is applied, the length of the bar is reduced by 0.018 in. Determine the magnitude of the force P. The moduli of elasticity are 29 x 10^6 psi for steel and 10 x 10^6 psi for aluminum. Please include the details. Thank you.
A 76 mm x 76 mm x 6 mm angular section is welded to a gusset plate having a thickness of 10 mm as shown in the figure. The length L1 equals 125 mm and L2 is 65 mm. The angular section has a cross sectional area of 929 mm2, Fy = 248 MPa, FU = 400 MPa. a. Determine the value of the tensile force P based on gross area in kN. b. Determine the value of tensile force P (KN) based on net area if the value of shear lag factor is 0.85. c. Determine the value of tensile force P based on block shear in gusset plate along the weld in kN. gusset plate L₂= 65 mm 25 m Allowable stresses: Allowable tensile stress (gross area) = 0.6Fy Allowable tensile stress (net area) = 0.50Fu Allowable shear stress (net area) = 0.30Fu P
H.W.1: A steel bar 6 m long is 5 cm in diameter for 3m of its length and 2.5 cm in diameter for the second 3m as shown in Figure below. The smallest diameter part of the bar is with 11 N/mm2 tensile stress due to the applied load. Find the final diameters of the two parts after the applied load. E for the steel is 200x10 N/mm and u of the steel is 0.28. P 3 m 3 m
Problem 1 A bar obtained by bonding together pieces of aluminum (Ea section shown below. Considering that the allowable stress (both in compression and tension) of aluminum and brass are 120 MPa and 180 MPa, respectively, determine the largest moment M that can be applied about the 70 GPa) and brass (Eb 105 GPa) has the cross horizontal axis. 8 mm 8 mm 32 mm- 8 mm 32 mm 8 mm Brass Aluminum
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
Q.2 The bar is made of an aluminium alloy having a stress-strain diagram that can be approximated by the straight line segment shown. Assuming that this diagram is the same for both tension and compression, determine the moment the bar will support if the maximum strain at the top and bottom fibers of the beam is E max = 0.05. 630 560 420 (MPa) 0.006 0.025 0.05 100mm M € (mm/mm) 75mm