Concept explainers
The ratio of solidification times of two castings.
Answer to Problem 5.64P
Given information:
The equation:-
Another casting is of elliptical cross-section:
Cross-sectional area of elliptical casting is same as of round casting. Both casting are done at same conditions.
Explanation of Solution
Calculation:
First determine the surface area and volume for each casting shapes:-
Round casting:-
Elliptical casting:-
Now, as per the chvarinov’s rule.
Solidification time,
Conclusion: The ratio of solidification times of two casting is 2.67.
Want to see more full solutions like this?
Chapter 5 Solutions
EBK MANUFACTURING PROCESSES FOR ENGINEE
- (b) In casting experiments performed using a certain alloy and type of sand mould, for which n can be approximately taken as 2, it took 155 sec for a cube-shaped casting to solidify. The cube was 50 mm per side. (i) Determine the value of the mould constant in Chvorinov's rule. (ii) When the same alloy and mould type are used to make a cylindrical casting of diameter 30 mm, what is the maximum length of the cylinder if the maximum solidification time is limited to 1 minute?arrow_forward(9,00 Puanlar) A riser in the shape of a sphere is to be designed for a sand casting mold. The casting is a rectangular plate, with 8- length 50 cm, width = 35 cm, and thickness = 4 cm. If the total solidification time of the casting itself is known to be 7,5 min, determine the diameter of the riser so that it will take 30% longer for the riser to solidify. %3D Riser volume: V3(TD3)/6(D%3Ddiameter) Riser area: A=TD2 Casting volume: V-L-Wt (L-Length, W=width, t-thickness) a) 8,41 cm b) O 7,34 cm c) 6.62 cm 11,46 cm Boş bırak KÖnceki 8/43 Sonraki> Каpatarrow_forwardA riser in the shape of a sphere is to be designed for a sand casting mold. The casting is a rectangular plate, with length = 100 mm, width = 50 mm, and thickness = 10 mm. If the total solidification time of the casting itself is known to be 2.5 min, determine the diameter of the riser so that it will take 20% longer for the riser to solidify. %3D %3!arrow_forward
- 4- A spherical riser must be designed for a sand-casting mold. The casting itself is a steel rectangular plate with dimensions 20 cm 10 cm 2.0 cm. Previous observation have indicated that the total solidification time (TTS) for this casting = 3.5 min. determine the diameter of the riser so that it will take 25% longer for the riser to solidifyarrow_forwardA riser in the shape of a sphere is to be designed for a sand casting mould at Simon Castings. The casting is a rectangular plate, with length = 400 mm, width = 250 mm, and thickness = 15 mm. If the total solidification time of the casting itself is known to be 7 min, determine the diameter of the riser so that it will take 30% longer for the riser to solidify.arrow_forwardA flat plate is to be cast in an open mold whose bottom has a square shape that is 200 mm by 200 mm. The mold is 40 mm deep. A total of 106 mm3 of molten aluminum is poured into the mold. Solidification shrinkage is known to be 6.0%. The linear shrinkage due to thermal contraction after solidification is 1.3%. If the availability of molten metal in the mold allows the square shape of the cast plate to maintain its 200 mm by 200 mm dimensions until solidification is completed, determine the final dimensions of the plate.arrow_forward
- Ratio of solidification time of a cylindrical casting (height = radius) to the cubic casting of side two times the height of cylindrical casting is %3Darrow_forwardflו. 3D) امتحان شهري.pdf 1. A square section riser be designed for a sand-casting mold. The casting itself is a quarter-cylinder with a diameter of 12cm and a length 20cm. The total solidification time for this casting = 0.9 min. The square for the riser will have a height-to-width ratio of 2.0. Determine the dimensions of the riser so that it is total solidification time = 1.2 2. A mold sprue is 180 mm long, the cross-sectional area at its base is 2.4 cm?. The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1600 cm?. Determine, volume rate of flow and time to fill the mold.arrow_forward1. A square section riser be designed for a sand-casting mold. The casting itself is a quarter-cylinder with a diameter of 12cm and a length 20cm. The total solidification time for this casting = 0.9 min. The square for the riser will have a height-to-width ratio of 2.0. Determine the dimensions of the riser so that it is total solidification time = 1.2 min.arrow_forward
- A cylinder with a diameter of 40 mm and height of 80 mm solidifies in 3 minutes in a sand casting operation. What is the solidification time if the cylinder height is doubled? What is the time if the diameter is doubled?arrow_forwardFor sand-casting a steel rectangular plate with dimensions 80mm×120mm×20mm, a cylindrical riser has to be designed. The height of the riser is equal to its diameter. The total solidification time for the casting is 2 minutes. In Chvorinov‟s law for the estimation of the total solidification time, exponent is to be taken as 2. For a solidification time of 3 minutes in the riser, the diameter (in mm) of the riser is ____arrow_forwardA cubical casting of 100 mm side is to be made from steel using an Al pattern (master pattern). For preparing the master pattern, a wooden pattern is used. Determine the dimensions of master pattern and wooden pattern. Use shrinkage allowance (mm/mm) for steel and Al as 0.021 and 0.013 respectivelyarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY