Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 18, Problem 18.8P
Calculate the allowable axial compressive load for a pin-connected hollow tube of aluminum using Euler’s formula and a factor of safety of 2.0. The tube is rectangular, 1 in. by 2 in. in cross section, with a wall thickness of 0.1 in. and a length of 48 in. The proportional limit of the material is 30,000 psi.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
1. A steel rod of 25 mm diameter is enclosed centrally in a copper hollow tube of external diameter 40 mm and internal diameter 30 mm. The composite bar is then subjected to an axial load of 4500 N.If the length of each bar is equal to 130 mm, calculate:
1. The stress in the rod and the tube
2. Load carried by each bar.
Take Es=2.1x105 N/mm2 and Ec=1.1x105 N/mm2
A link in an automated packaging machine is a hollow tube made from 6061-T6 aluminum. Its dimensions are as follows: outside diameter = 32.0 mm, inside diameter = 28.0 mm, and length = 1.00 m. Compute the tensile force required to produce an elongation of the bar of 1.3 mm. Would the stress produced by the force just found be safe if the load is applied repeatedly?
A compound tube consists of a steel tube 120 mm internal diameter and 140 mm external diameter and an outer brass tube 140 mm internal diameter and 10 mm thickness. The two tubes are of the same length equal to 150 mm. The compound tube carries an axial load of 800 kN. Estimate the stresses and the load carried by each tube and the amount it shortens. Take E for steel as 2 × 105 N/mm2 and for brass as 1 × 105 N/mm2.
Chapter 18 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 18 - Calculate the Euler buckling load for an axially...Ch. 18 - Calculate the Euler buckling load for a...Ch. 18 - A pin-connected axially loaded compression member...Ch. 18 - Prob. 18.4PCh. 18 - Plot a curve showing the relationship of feversus...Ch. 18 - A W1222 structural steel wide-flange section is...Ch. 18 - Prob. 18.7PCh. 18 - Calculate the allowable axial compressive load for...Ch. 18 - A W20059 structural steel wide-flange section is...Ch. 18 - Use Euler’s formula and a factor of safety of 2.5...
Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - Prob. 18.17PCh. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26 assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For the following computer problems, any...Ch. 18 - For the following computer problems, any...Ch. 18 - Calculate the Euler buckling load for an axially...Ch. 18 - 18.32 Calculate the Euler buckling load for an...Ch. 18 - 18.33 A structural steel shape of ASTM A992 steel...Ch. 18 - Calculate the Euler buckling load for a...Ch. 18 - 18.35 Rework Problem 18.34 assuming that the...Ch. 18 - 18.36 A built-up steel column is made by welding a...Ch. 18 - A 2-in-diameter standard-weight steel pipe is used...Ch. 18 - A structural steel column is 30 ft long and must...Ch. 18 - 18.39 Compute the allowable axial compressive load...Ch. 18 - 18.40 Determine the allowable axial compressive...Ch. 18 - 18.41 Using the AISC column approach, compute the...Ch. 18 - Using the AISC column equations, select the...Ch. 18 - Select the lightest extrastrong steel pipe section...Ch. 18 - 18.44 Compute the required diameter of a steel...Ch. 18 - 18.45 A 19-mm-diameter steel rod is 350 mm in...Ch. 18 - 18.46 A pin-connected linkage bar is 16 in. long...Ch. 18 - Prob. 18.47SPCh. 18 - Prob. 18.48SPCh. 18 - Prob. 18.49SPCh. 18 - Prob. 18.50SPCh. 18 - Prob. 18.51SP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?arrow_forward. A steel boiler 2.5 m in diameter has a wall thickness of 25 mm. The internal pressure is 1.6 MPa. Calculate the factor of safety if the maximum permissible stress for it is 250 MPa?arrow_forward1. Use the tabulated solutions: Calculate the critical buckling stress for each of the flat plates shown. All are made from steel with E = 29 X 106 psi and v = 0.30 and are 3/16 inch thick. All edges are simply supported. (a) 48 in 48 in ' (b) 96 in 48 in (c) 48 in Note: if the tabulated solutions do not include the exact geometry ratio that you are looking for, interpolate between values in the table. 96 inarrow_forward
- Situation 2: A steel plate 8 mm thick is to be embedded in a horizontal concrete slab and is used to anchor a high-strength vertical cable 12 mm in diameter as shown. The diameter on the hole on the plate is 20 mm. Assuming that P = 10 kN, determine the safest minimum dimensions a and b as the width of the plate and the depth of embedment, respectively. Consider the following design parameters: P Allowable stresses: Normal stress of steel 250 MPa Bonding stress of steel and concrete : 5 kPa Note: Neglect the stress between the concrete and the bottom face of the plate. 8 mm A. Dimension a (mm) 20 mm-dia. B. Dimension b (mm) C. What is the factor of safety for the anchorage of the steel plate in the concrete slab if a = b 50 mm and b = 90 mm? aarrow_forwardThe one end of a hollow square tube whose side is 10.47 in with 1.47 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using (a double-pin) system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ(allowable) = 243 ksi for pin material.arrow_forwardAxial loads are applied with rigid bearing plates to the cylindrical pipes shown. The diameter of aluminum pipe (1) is 1.70 in. with a wall thickness of 0.25 in., the diameter of brass pipe (2) is 1.50 in. with a wall thickness of 0.25 in., and the diameter of steel pipe (3) is 3.00 in. with a wall thickness of 0.25 in. Pipe (2) has a length of 14 in. and deforms 0.22 in. due to the applied loads. (a) Determine the axial stress in rod (2) and state whether it is in compression or tension. (b) Calculate the normal strain in rod (2). 4₂ = 141n ad Deforms (P) = . 22, h compression Given; d = 1.70in t₁ = .25in d₂ = 1.50in t₂ =125in = 3.00in t₂ =.25in dz 1.501h-2 (₁25in) = lin A = π (1,60² - 1₁m²) = 98 m² 14in-,22iK 13.78 212 60kips 9814² = 1.981h = E €61.22 ks/ A 15 kips 15 kips 20 kips 30 kips 35 kips B 20 kips 35 kips Darrow_forward
- A simplified model of a basketball hoop is shown. During a basket dunk a player hangs from the rim applying a force of 320 lbs including a dynamic load factor. The stand is a square tube with 5 inches outside length and 0.25 inches thickness. The distance from the edge of the rim to the middle of the square tube is 4 ft. Assuming the model is rigid, the normal stress at point A is most closely equal to: A 36 psi 1284 psi 1248 psi 1212 psiarrow_forwardA spherical pressure vessel is constructed by bolting two hemispheres together along rigid flanges as shown in the sketch. The sphere has an internal diameter of 1.5 m and the plate thickness is 5 mm. Allowable tensile stresses are 45 MPa in the shell and 80 MPa in the bolts. 1. Calculate the allowable gauge pressure 2. Determine the number of bolts required if the bolt diameter is 25 mm (Note: bolt root diameter = 0.84 × nominal bolt diameter) 3. A thin copper tube, 14 mm internal diameter and 0,5 mm wall thickness has closed ends and rotates at 1200 r/min while it is subjected to an internal gauge pressure of 222 Pa. Calculate the total hoop stress in the wall of the tube if the density of copper is 8900 kg/m3.arrow_forward. A short steel tube of external diameter 70 mm and internal diameter 40 mm is surrounded by a brass tube of same length and having external diameter 90mm and internal diameter 80 mm. The tubes are rigidly fixed and an axial load of 20 kN is placed on the tubes. Find the load carried in each tube and shortening of each tube. Take L = 30 cm, modulus of elasticity of steel is 2.1 x 105 N/mm2and modulus of elasticity of brass is 1.1 x 105 N/mm2.arrow_forward
- A square tie bar 20 mm x 20 mm in section carries a load. It is attached to a bracket by means of 6 bolts. Calculate the diameter of the bolt if the maximum stress in the tie bar is 150 N/mm2 and in the bolts is 75 N/mm2.arrow_forwardCalculate the change in dimensions in the bar.F = 12000 N; h= 0.01 m; w= 0.03 m; L = 0.8 m; E = 60 GPa; v = 0.3arrow_forwardThe one end of a hollow square bar whose side is 10.17 in with 1.17 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ allowable= 243 ksi for pin material.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Mechanics of Materials Lecture: Beam Design; Author: UWMC Engineering;https://www.youtube.com/watch?v=-wVs5pvQPm4;License: Standard Youtube License