Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 18, Problem 18.20P
For Problems 18.18 through 18.21, use the Euler-Johnson formulas, Equations (18.9) and (18.10), and a modulus of elasticity of 30,000,000 psi.
18.20 Compute the required diameter of an air cylinder piston rod of AISI 1040 hot-rolled steel. The rod has a length of 54 in. and is subjected to an axial compressive load of 1900 lb. Assume pinned ends. Use a factor of safety of 3.5.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Compute the design factor in the middle portion only of the rod AC if the steady vertical force on the boom is 2500 lb. The rod is rectangular, 1.50 in by 3.50 in, and is made from SAE 1144 cold-drawn steel. Include a mohr circle.
The tensile load on the bar mentioned varies from 4,000 lb to a minimum of 1,200 lb. Rapid cycling for many million cycles is expected. As the tensile load fluctuates between 4,000 lb and 1,200 lb, it creates fluctuating normal stresses. Calculate the following stresses at the section through the hole.
Note: SAE 1050 OQT 1300 steel, wrought steel
(a) Maximum tensile stress (psi)
(b) Minimum tensile stress (psi)
(c) Median stress (psi)
1. A piston rod, made of AISI 3140 steel, OQT 1000 F, is subjected to a repeated, reversed load. The rod
is for a 20-in. air compressor, where the maximum pressure is 125 psig. Compute the diameter of the rod
using a design factor based on:
(a) ultimate strength, 1.62 in 1 5/8 in
(b) yield strength. 1.23 in = 1 % in
For AISI 3140 steel, OQT 1000 F
Su = 152 5. ksi
Nu = 8
Sy = 132 5. ksi
Ny = 4
Chapter 18 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 18 - Calculate the Euler buckling load for an axially...Ch. 18 - Calculate the Euler buckling load for a...Ch. 18 - A pin-connected axially loaded compression member...Ch. 18 - Prob. 18.4PCh. 18 - Plot a curve showing the relationship of feversus...Ch. 18 - A W1222 structural steel wide-flange section is...Ch. 18 - Prob. 18.7PCh. 18 - Calculate the allowable axial compressive load for...Ch. 18 - A W20059 structural steel wide-flange section is...Ch. 18 - Use Euler’s formula and a factor of safety of 2.5...
Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - Prob. 18.17PCh. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26 assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For the following computer problems, any...Ch. 18 - For the following computer problems, any...Ch. 18 - Calculate the Euler buckling load for an axially...Ch. 18 - 18.32 Calculate the Euler buckling load for an...Ch. 18 - 18.33 A structural steel shape of ASTM A992 steel...Ch. 18 - Calculate the Euler buckling load for a...Ch. 18 - 18.35 Rework Problem 18.34 assuming that the...Ch. 18 - 18.36 A built-up steel column is made by welding a...Ch. 18 - A 2-in-diameter standard-weight steel pipe is used...Ch. 18 - A structural steel column is 30 ft long and must...Ch. 18 - 18.39 Compute the allowable axial compressive load...Ch. 18 - 18.40 Determine the allowable axial compressive...Ch. 18 - 18.41 Using the AISC column approach, compute the...Ch. 18 - Using the AISC column equations, select the...Ch. 18 - Select the lightest extrastrong steel pipe section...Ch. 18 - 18.44 Compute the required diameter of a steel...Ch. 18 - 18.45 A 19-mm-diameter steel rod is 350 mm in...Ch. 18 - 18.46 A pin-connected linkage bar is 16 in. long...Ch. 18 - Prob. 18.47SPCh. 18 - Prob. 18.48SPCh. 18 - Prob. 18.49SPCh. 18 - Prob. 18.50SPCh. 18 - Prob. 18.51SP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A structural support for a machine will be subjected to a static tensile load of 16.0 kN. It is planned to fabricate the support from a square rod made from SAE 1020 hot-rolled steel. Specify suitable dimensions for the cross section of the rod.arrow_forwardsimple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 mm outside diameter with threaded ends. What will be the nominal stresses set up in the tube and the rods, ignoring thread depth, when the turnbuckle carries an axial load of 30 kN? Assuming a sufficient strength of thread, what maximum load can be transmitted by the turnbuckle if the maximum stress 1s limited to 180 MN/m*?arrow_forwardThe figure shows the handle super fast byke and its geometry with forces The cross section at the critical location is elliptical, with a major axis of 3 in and a minor axis of 1.5 in. For a load of 20 kip, estimate the stresses at the inner and outer surfaces of the critical section. 12-in R. 12-in R. 9 inarrow_forward
- 6. A circular bar is to carry a fluctuating torque from 25 to 55 N-m. Use AISI C1144 OQT 1000for the bar and compute for the required diameter for a design factor of 2. Attachmentsproduce a stress concentration of 2.5 near the ends of the bar. please also give the FBD, thank youarrow_forwardA structural support for a machine will be subjected to a static tensile load of 16.0 kN.Specify suitable dimensions for the cross section of the rod.arrow_forwardPROBLEMS: 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850 in-lb. The shaft diameter is 1.75 inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, find A. Force that will shear the pin B. Shear pin diameterarrow_forward
- A mild steel tie-rod has to carry an axial load of 60KN. The maximum permissible stress is 200N/mm2. Calculate a suitable diameter for the rod.arrow_forwardA short hollow, cast iron cylinder with wall thickness of 10 mm is to carry compressive load of 100 kN. Compute for the working stress in compression if the outside diameter `D' is 48.75 mm). Q 10 mm Darrow_forwardAn aluminum rod, made from alloy 6061-T6, is made in the form of a hollow square tube, 2.25 in outside with a wall thickness of 0.125 in. Its length is 16.0 in. It carries an axial compressive force of 12 600 lb. Compute the resulting design factor. Assume that the tube does not buckle.arrow_forward
- A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook.arrow_forward1. The tie-rods in the press in Figure are made of the steel alloy SAE 5160 OQT 900 (E=30×106 psi). Each rod has a diameter of 2.00 in. and an initial length of 68.5 in. An axial tensile load of 40 000 lb is exerted on each rod during operation of the press. Compute the deformation of the rods. Press frame Ram Circular steel tie rod attached to press frame Die A cross sectional area Original length Total deformationarrow_forwardA closely coiled helical spring of mean diameter 140 mm is made up of 12 mm diameter steel wire. Calculate the direct axial load, the spring can carry if the maximum stress is not to exceed 100 MPa.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY