Concept explainers
The intrinsic electrical conductivity of
The intrinsic electrical conductivity of
Answer to Problem 82AAP
The intrinsic electrical conductivity of
The intrinsic electrical conductivity of
Explanation of Solution
Write the expression for the conductivity of
Here, the intrinsic carrier is
Convert the temperature from degree Celsius to Kelvin.
Convert the temperature from degree Celsius to Kelvin.
Write the expression for the conductivity of
Here, the Boltzmann constant is
Write the expression for the conductivity of
Conclusion:
Here, the charge is
Substitute
Substitute
Substitute
Thus, the intrinsic electrical conductivity of
Thus, the intrinsic electrical conductivity of
Want to see more full solutions like this?
Chapter 14 Solutions
Foundations of Materials Science and Engineering
- Engineering science Distinguish elastic, electrical and magnetic hysteresis in different Materials.arrow_forwardA 4.0-nm-diameter protein is in a 0.050 M KCl solution at 25° C. The protein has 9 positive and 20 negative charges. Model the protein as a sphere with a uniform surface charge density. Part A What is the electric potential of the protein at the surface? Express your answer with the appropriate units. μA ? Vsurface = Value Units Submit Request Answer Part B What is the electric potential of the protein 2.0 nm from the surface? Express your answer with the appropriate units. με V2 nm = Value Units Submit Request Answerarrow_forwardYour answer is partially correct. The ammonia molecule NH3 has a permanent electric dipole moment equal to 1.47 D, where 1 D-1 debye unit-3.34 x 10-30 C-m. Calculate the electric potential in volts due to an ammonia molecule at a point 46.7 nm away along the axis of the dipole. (Set V-0 at infinity.) Number 2.26E-5 Units Varrow_forward
- 4. Fermi-Dirac statistics Develop an Excel sheet to numerically calculate the numbers of electrons with energies above the Fermi energy level EF = 5.5 eV in silver at 300 K and 1000 K, assuming EF does not change with temperature. m mm marrow_forwardAn ideal capacitor with a capacitance of 90.0 nF is charged up to a voltage of 3.00 V. (i) Calculate the magnitude of charge stored in the capacitor. (ii) Determine the potential energy stored in the capacitor. (iii) The capacitor is disconnected from the battery and is then inserted with a piece of mica of which the dielectric constant is 5.00. Compare the final potential energy to the initial potential energy in the capacitor.arrow_forwardA charged nonconducting rod, with a length of 2.52 m and a cross-sectional area of 4.76 cm², lies along the positive side of an x axis with one end at the origin. The volume charge density p is charge per unit volume in coulombs per cubic meter. How many excess electrons are on the rod if p is (a) uniform, with a value of -4.66 µC/m³, and (b) nonuniform, with a value given by p= bx², where b = -2.18 µC/m²? (a) Number i (b) Number i Units Unitsarrow_forward
- QUESTION Consider a uniformly doped silicon p-n junction at T=300°K. At zero bias, only 40 percent of the total space charge region is to be in the p-region. The built-in potential barrier is 1.2 volts. For zero bias determine total space charge region. (q=1.6x1019, kT/q=0.0259 volts at T=300°K, n=100 cm, e=103.545x104)arrow_forwardAt room temperature (20°C) the electrical conductivity of Gallium phosphide (GaP) is 63 (2.m)–1, whereas the electron and hole mobility are 0.24 and 0.057 m²/V-s, respectively. a) Compute the intrinsic carrier concentration for GaP at room temperature, (q=1.6 x 10 -19 c). b) If the energy gap of GaP is 0.92 eV, calculate its conductivity at 70°C (k= 8.62 x 10 eV/K). -5arrow_forwardA wire carrying 0.50 A of current is place in a magnetic field with a strength of 0.75 T. The length of the wire is 41 cm. What is the magnitude of the magnetic force on the wire?arrow_forward
- 1. What is the total flux passing through a 10 cm x 6 cm surface in a region where the electric flux density is 2700 µC/m? ? [1.62 x 105 C]arrow_forwardA rod of semiconducting material of lenght L=3 m and cross-sectional area A=4.5 mm^2 lies along the x-axis between x=0 and x=L. The material obeys ohm's law, and resistivity varies along the rod according to p=p0 (1-(x^2/L^2)) where p0= 4.10^-4 ohm.m. The end of the rod x=0 is at a potential V0=30V greater than the x=L. A) what is the total resistance, in units of ohm, of the rod? B) what is the current, in units of miliamperes, in the rod? C) what is the electric potential, in units of Volt, in the rod at x=L/2? D) what is the electic-field magnitude E, in units of V/m, in the rod at x=L/2?arrow_forwardIf 5.8x1020 electrons are deposited on the positive plate of a capacitor by applied voltage of 40V, find the capacitance of the capacitor? (Analysis)arrow_forward
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning