The bracket shown is welded by an E70 electrodes fillet weld and is subjected to a factored load Pu=290KNa.) Determine the polar moment of inertia of the group of welds.b.) Determine the max force per mm to be resisted by the weld as shown.c.) Determine the fillet weld size required for the connection.P = 290 kN175 mm150 mmChannelSection500 mmWelding at the backof the channel

A bracket is shown in the figure which is welded by E70 electrode and the weld type is fillet weld…

The bracket shown is welded by an E70 electrodes fillet weld and is subjected to a factor .) Determine the polar moment of inertia of the group of welds. ) Determine the max force per mm to be resisted by the weld as shown. :) Determine the fillet weld size required for the connection. P = 290 kN 175 mm 150 mm Channel Section 500 mm

The bracket shown is welded by an E70 electrodes fillet weld and is subjected to a factor .) Determine the polar moment of inertia of the group of welds. ) Determine the max force per mm to be resisted by the weld as shown. :) Determine the fillet weld size required for the connection. P = 290 kN 175 mm 150 mm Channel Section 500 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.5.2P

See similar textbooks

Similar questions

1. Design the fillet weld connection between the double equilateral angle steel and gusset plate shown in the figure. The steel is Q235B while the welding rod is E43, then the design value of weld strength f, is 160 N/mm², and the size of fillet weld hf is chosen as 8mm. If the axial force N = 1000KN, please calculate the effective lengths of the side fillet welds on both sides of angle steel under the condition of (1) two side welding is used, and (2) three side welding is used, respectively. t=12 N 2L125X10
Plate is connected to the column using fillet welds as shown. The size of weld is 12 mm. Determine the following: Locate the center of gravity of the weld group from the vertical part of the weld. Stress due to moment. Max stress due to combined moment and load. 100KN 4 100mm 55mm 150mm 55mm 110mm 3
The connection is shown in Fig. 3. Two cover plates are applied to connect the steel plates by fillet welds. The dimensions of connection are presented in Fig. 3. The leg size of fillet weld hr is 10 mm. Q235 steel, f-215 N/mm2, E43 electrode, fav=160N/mm?. Calculate the load-carrying capacity of the fillet weld connection wwww. (Note: the strength of steel plate should be calcualted. (Unit: mm) 220 ス20 091
a. Determine the design strength of a 1-in length of a 1/4-in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength FEXX = 70 ksi. Assume that load is to be applied parallel to the weld length.b. Repeat part (a) if the weld is 20 in long.c. Repeat part (a) if the weld is 30 in long.
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
Two steel plates, each 400mm wide and 12mm thick, are to be joined together by a lap splice (single). The electrode to be used for the weld has a nominal tensile strength of 550Mpa. Determine the following:a. the maximum weld size that can be usedb. effective net area of the fillet weld using the maximum weld size allowed by the manualc. the maximum load that can be resisted by the weld using the maximum weld size allowed by the manual.
A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back of the channel. All steel is A36 with Fy=250 MPa and Fu=400 MPa. Use E70electrodes having and Fu=485 MPa (SMAW) process. The maximum length of lap is 250mm. The size of fillet weld is 8mm. Assume the width of slot weld is 22 mm. Size of slot weld is 13mm Properties of C250x37 A = 4750 mm2 tw = 13.0 mm2 d = 254 mm a. Determine the force resisted by the slot weld in kN, when the full tensile capacity is 712.5 KN (from the gross yielding capacity using ASD) Hint: Full tensile Capacity = Force Resisted by Fillet and Slot Weld Round your answer to 3 decimal places.
A welded bracket connection is shown in figure. It supports a factored load of 150 kN at a distance of 120 mm from the face of column. Design the fillet weld on two sides. Grade of steel = Fe410, f. = 250 MPa. y 120 mm P₁ = 150 kN Fillet weld t = 12 mm
The angle 150x100x100 mm is connected to the gusset plate. The size of weld is 8 mm and using E70 electrodes. Fu = 438 MPa Question: a.) Find the length of the weld required at the toe of the angle. b.) Find the length of the weld required at the heel of the angle.
In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁=C₁ = 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem The angle 150x100x10mm is connected to a 8.5 mm gusset plate. The size of weld is 8 mm and using E70 Electrodes. Fu = 438 MPa. Use LRFD. Questions: a) Find the length of the weld required at the toe of the angle. b) Find the length of the weld required at the heel of the angle. c) Find the block shear strength of the gusset plate.
Calculate the maximum shear force in the welds in the given figure. P=160kN X = 150mm y= 125mm z=70mm 4 Y N