In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁ = C,= 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.

In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁ = C,= 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.13P

See similar textbooks

Similar questions

Plate is connected to the column using fillet welds as shown. The size of weld is 12 mm. Determine the following: Locate the center of gravity of the weld group from the vertical part of the weld. Stress due to moment. Max stress due to combined moment and load. 100KN 4 100mm 55mm 150mm 55mm 110mm 3
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
A welded bracket connection is shown in figure. It supports a factored load of 150 kN at a distance of 120 mm from the face of column. Design the fillet weld on two sides. Grade of steel = Fe410, f. = 250 MPa. y 120 mm P₁ = 150 kN Fillet weld t = 12 mm
a. Determine the design strength of a 1-in length of a 1/4-in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength FEXX = 70 ksi. Assume that load is to be applied parallel to the weld length.b. Repeat part (a) if the weld is 20 in long.c. Repeat part (a) if the weld is 30 in long.
A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back of the channel. All steel is A36 with Fy=250 MPa and Fu=400 MPa. Use E70electrodes having and Fu=485 MPa (SMAW) process. The maximum length of lap is 250mm. The size of fillet weld is 8mm. Assume the width of slot weld is 22 mm. Size of slot weld is 13mm Properties of C250x37 A = 4750 mm2 tw = 13.0 mm2 d = 254 mm a. Determine the force resisted by the slot weld in kN, when the full tensile capacity is 712.5 KN (from the gross yielding capacity using ASD) Hint: Full tensile Capacity = Force Resisted by Fillet and Slot Weld Round your answer to 3 decimal places.
Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONS
1. Design the fillet weld connection between the double equilateral angle steel and gusset plate shown in the figure. The steel is Q235B while the welding rod is E43, then the design value of weld strength f, is 160 N/mm², and the size of fillet weld hf is chosen as 8mm. If the axial force N = 1000KN, please calculate the effective lengths of the side fillet welds on both sides of angle steel under the condition of (1) two side welding is used, and (2) three side welding is used, respectively. t=12 N 2L125X10
Two steel plates, each 400mm wide and 12mm thick, are to be joined together by a lap splice (single). The electrode to be used for the weld has a nominal tensile strength of 550Mpa. Determine the following:a. the maximum weld size that can be usedb. effective net area of the fillet weld using the maximum weld size allowed by the manualc. the maximum load that can be resisted by the weld using the maximum weld size allowed by the manual.
The single 200mm x 10mm steel plate is connected to a 12mm thick steel plate by four 16mm diameter rivets as shown. The rivets used are A502, Grade 2, hot driven rivets. The steel is ASTM A36 with Fu = 400MPa. Determine the value of P in all possible modes of failure and the safe value of P that the connection can resist.
Problem 14.3.A A 4 × 4 × ½-in. angle of A36 steel is to be welded to a plate with E 70 XX electrodes to develop the full tensile strength of the angle. Using %-in. fillet welds, compute the design lengths for the welds on the two sides of the angle, assuming development of tension on the full cross sec- tion of the angle. A=3.75 inch2 L1= 10.94" L2 = 5.09" IF only connected leg, L=7.7"; 4.75 each side
4.) A 150 x 90 x 12 angular section is welded to a gusset plate as shown in the figure. The angle is A36 steel with FY=248 MPa. The weld is E 80 electrode with Fu = 550 MPa. The allowable tensile stress for the angle is 0.6Fy and the allowable shear stress for the weld is 0.3Fu. The Area of the angular section is 2751 sq.mm. with y=51mm. CS 56 Which of the following most nearly gives the design force P? a.) 400,365.9 N b.) 409,348.8 N c.) 412,793.5 N d.) 420,366.6 N 5.) A W350 x 90 steel is used as a simply supported beam 8m long. The beam carries three equal concentrated loads at every quarter points. It also carries a uniform dead load o 5 kn/m (including its own weight) and a uniform live load of 7.20 kn/m. Properties of W 350 x 90 steel: bf = 250 mm The allowable bending stress is 0.66Fy. The allowable shear stress is 0.40Fy. The allowable deflection is L/360. Use Fx=248 Mpa and E=200 Gpa. tf = 16.40 mm V d = 350 mm Determine the maximum value of each concentrated load based on…
Calculate the maximum shear force in the welds in the given figure. P=160kN X = 150mm y= 125mm z=70mm 4 Y N