procedu Mnnjos io aun d au Problem 3. What do you think you have to do now? Yes. An equilibrium 2D problem! Do not use decimals. Distances should be integers between 1 to 6 meters. The body is a cylinder of known radius (integer number) and known mass (you decide). You will decide the type of supports that are holding the body at rest. Two known external non-parallel forces and a known external couple are applied at the body. One external force must be a diagonal and its slope marked with a known triangle (So sorry, again). Write 3 equations for equilibrium and solve them numerically. Draw the free body diagram and show the procedure of the solution.

procedu Mnnjos io aun d au Problem 3. What do you think you have to do now? Yes. An equilibrium 2D problem! Do not use decimals. Distances should be integers between 1 to 6 meters. The body is a cylinder of known radius (integer number) and known mass (you decide). You will decide the type of supports that are holding the body at rest. Two known external non-parallel forces and a known external couple are applied at the body. One external force must be a diagonal and its slope marked with a known triangle (So sorry, again). Write 3 equations for equilibrium and solve them numerically. Draw the free body diagram and show the procedure of the solution.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.129P: The uniform 240-lb bar AB is held in the position shown by the cable AC. Compute the tension in the...

See similar textbooks

Similar questions

What is the ratio L/R for which the uniform wire figure can be balanced in the position shown?
Problem: In the probiem below, distances are specified from left to right. The distance between point B and the force of magnitude P is 0.5 m, distance between force of magnitude P and 4P is 1 m, between the force of 4P and the next identical force of 4P is 1.5 m, between that of the force 4P and 2P ois 1.5 m, and between pin at A and the force of magnitude 2P is 0.5 m. a) Determine the support reactions at A, B and C. b) If the cross section of BC is a square of side 20 mm, determine the average normal stress at any point between B and C. c) Draw the state of stress on a volume element. 111L 4P 2P 30 B A 米 0,5m Im 1.Sm P= 15 KN
A uniform ladder 8 meters long and weighing 350 N rest against a smooth vertical wall at an angle of 30 to the wall. A 700-N man stands 6 meters up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping Show the Figure/FBD, given and the formula used
The figure on the left, below, shows a non-uniform bent rod with a mass of 5 kg. Your job is to determine the location of the center of gravity of this rod. You design an experiment: you connect a pin and cable to the rod such that it safely stays in static equilibrium under a force P that you apply. Then, you apply forces between 0-100 N, and measure the tension force on the cable using a cable tension meter. The results of your experiment are shown in the figure, on the right. Using this experiment, calculate (approximately) the horizontal distance (x in the figure) between point A and the center of gravity G of the bent rod. B C O I 20 cm 20 cm 60° D 50 cm Tension measurement [N] 60 50 40 30 20 -10 0 10 real data estimated fit 20 30 40 ܐܐܝ 50 P[N] 60 70 80 90 100
1. The PASCO human arm model is configured such that the cord representing the bicep is perfectly vertical and the forearm is at 90° (in the figure to the right, the cord is not quite vertical). A mass of 100 g is attached to the hand. Draw a free-body diagram on the figure to the right showing all forces which act on the forearm. The force of the bicep F on the arm The force of the humerus FH on the arm The weight of the forearm W The mass in the hand Wm 100 g Be careful to draw the force vectors with tails beginning at the point where the force is actually applied to the forearm. 2. Consider the free body diagram below. Determine the perpendicular component F̟ of the force F exerted by the biceps brachii on the forearm. Use the fact that cos 0 = H/B to write this component directly in terms of the humerus length H and the biceps length B. H 3. If the forearm is in equilibrium, then there is no angular acceleration and therefore the sum of the torques applied to the forearm must be…
A weight W= 120 kN is being supported by steel sections with force T, force F, andforce C. The coordinates of A, B, C, and D are given. Assume that E is the origin(0,0,0). Determine Forces T, F, and C. (Hint: Produce three equations fromequilibrium of force system)Note: The Forces T, F, and C must be computed accurately to design the proper sizes ofsteel sections in the subject “Steel Design.”
A truss is facing a two-force member and both of them are in the opposite directions, and the truss is in equilibrium. And both of them are coming to each other. The forces are called Select one: O a. Tensile Forces O b. Compressive forces O c Parallel and collinear forces with same direction of heading O d. The rotational forces Next page est-3 Jump to...
Planar Linkages: Determine the number of links, the number of 1 degree and/or 2 degree joints. The links should be properly numbered. Find mobility of the system. 1. 2.
Could you help me with the first few steps on solving this using vectors? I need to calculate the forces in AB and BC. I don't the answer right away but I don't know where to start.
Pivot A constant density bar with mass m and length Lis held in place as shown. Use the usual x,y,z coordinates for the following questions. Celling Cable 12. Measuring from the pivot, in the space below draw the torque-pic for the weight force exerted on the bar. Be sure your torque-pic includes both an expression for r in terms of L and also the value for the angle between r and weight force. Bar 350 Length = L
Lessons: Static of Rigid Bodies, Force Vector, Addition of a System of Coplanar Forces, Cartesian Vector, Etc. Kindly answer the following with complete solution. Please also draw the free-body diagram or illustration of your figure. Make sure to write with understandable hand-writing. Please send a clear picture of complete solution. I need the answer within an hour at least. I'll rate you with a like/upvote. Thank you.
Q3 a. Define the following term 1. Lateral vehicle dynamics 2. oversteers 3. steering wheel shimmy 4.d'Alembert Force Q3 b When deriving the force acting on the wheel to determine the maximum grade we can E without wheel slippage (traction limited gradeability) then Write the equation that relate total mass of the vehicle in case of a Front wheel duiveWD ), on Rear wheel Drive (RWD in case of All wheel drive (4WD) power train ? s