OBJECTIVE 4-2 OP AMP CIRCUIT ANALYSIS (SECTS. 4-3 AND 4-4) Given a linear resistance circuit containing OP AMPS, find selected output signals or input-output relationships. See Examples 4-12 to 4-20 and Exercises 4-15 to 4-31. SS 4-19 Find the voltage gain of each OP AMP circuit shown in Figure P4-19. VS 10 ΚΩ w 10 ΚΩ M 560 ΚΩ w VS (a) 560 ΚΩ (b) FIGURE P4-19 Vo VO

OBJECTIVE 4-2 OP AMP CIRCUIT ANALYSIS (SECTS. 4-3 AND 4-4) Given a linear resistance circuit containing OP AMPS, find selected output signals or input-output relationships. See Examples 4-12 to 4-20 and Exercises 4-15 to 4-31. SS 4-19 Find the voltage gain of each OP AMP circuit shown in Figure P4-19. VS 10 ΚΩ w 10 ΚΩ M 560 ΚΩ w VS (a) 560 ΚΩ (b) FIGURE P4-19 Vo VO

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Design an op-amp circuit to yield the relationship shown in each equation. Vo = V1 + 10V2 – 30V3 – 100 V4a.) Rmin = 6kΩb.) Rin = 6kΩ
Figure Q4(b) shows an amplifier block diagram. Design using MORE THAN ONE op-amps which have one common input signal and two output signals. Shows all necessary calculation of the design. Vil: - 200mV Figure Q4(b) • Vo2 = 20mV Vo3 = - 1V
R, V OUT Let currents and node voltage for the Op-Amp circuit be defined as follows: |1 equals the current flowing through Rin from left to right. Let Vb be the voltage at the inverting input (-). Write 1 in terms of the node voltages Vin, Vb (voltage at inverting input). O Vb - Vin O Vvin - Vb O (Vb - Vin)/Rin O Vin - Vb) / Rin O - Vin/Rin
Q4: Baginning in position1 in figure,the switch is thrown into position2 and held there for 10ms, then back to position1 for 10ms,and so forth.sketch the resulting output waveform if its initial value is 0v, the saturated output levels of the op-amp +-12v? +5V R. 10LF 10K2 -5V
The circuit below, you may note, does not match any of the common op-amp circuits. By performing circuit analysis, determine the voltage across the load resistor R5. You may assume that V1 = 4.3 V, V2 = 5.4 V, R1 = 49 kQ, R2 = 85 KQ, R3 85 KQ, R4 = 66 kQ, and R5 = 68 kQ. = R1 V1 + R2 V2 R3 R4 R5 m
From the figure , write note voltage equations, one for each input terminal of the op amp The expression for the load current ( iL) can be written as a function of the input voltage (Vin) and the load voltage (VL) IL =A(Vin) + B(VL) b.1 What is the expression for A? b.2 What should be the condition for R1 R2 R3 R4 so that B is zero? (NB this will make( iL) depend only on Vin and not on RL)
Determine what kind of operation amplifier this is. Find Vour and Graph all inputs vs. output, when VIN(1) = .5sinwt, VIN(2) = .6sinwt, and VIN(3) = sinwt. Op-amp is powered with +9V and -9V batteries. VIN (1) VIN (2) VIN (3) R₁-822 R₂-1002 www R3-40022 RF -1k2 www 7 + VOUT
If the ideal design for op-Amp circuit bli 3 generate 200 mV at the output, Then practically with 26 mV offset voltage the output voltage of the circuit will be equal to. mV
1. Given that the input V1(t) in Figure 4 (a) is a 3V peak triangle wave at 4 kHz.Answer the following 2.The circuit in Figure 4 (b) has 5 op-amps labeled as U1 through U5. State what the op-amp circuit is for U1 Circuit: U2 Circuit: U3 Circuit: U4 Circuit: U5 Circuit: 3. Determine the values of VO1, VO2, VO3, VO4 and VO5. 4. Draw the output waveform at VO5 for the given input waveform shown in Figure 4 (a).
Consider the circuit shown in the figure below. The figure consists of an ideal op-amp circuit. The transfer characteristics of the circuit can be represented as R, D, 7 R, ww D2 2R2 -15 V
3. Design an op-amp circuit (using exactly 2 op- amps) that does the following mathematical operation: 4V, + 1 3V₂ - 6V₂. 2 3°
Sketch the output voltage waveform for each op armp circuits given below. Given the maximum outputvoltage for the op-armp is Vomax = +10 v and Vomin = -10 v.Use input voltage for all circuit as shown. Also use V2 = 4.7 V for D1 and D2. V. 0 -5V- -5V D1 Kt 1K 1K D2 V1 V2