Consider a step up converter with a resistive load of value R-5 Ohms. It is supplied by a DC power source of magnitude Vs=200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L=10 mH. The switch is supposed to be ideal. The peak input current 12 = 81A. RMS load current 10 is equal to: Select one: a. 39.15A Ob. None of these O c. 74.36A O d. 55.16A 4

Consider a step up converter with a resistive load of value R-5 Ohms. It is supplied by a DC power source of magnitude Vs=200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L=10 mH. The switch is supposed to be ideal. The peak input current 12 = 81A. RMS load current 10 is equal to: Select one: a. 39.15A Ob. None of these O c. 74.36A O d. 55.16A 4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. The circuit given below is using a transformer of 230V/30V. The load resistance is 10KS. Find Vin (rms and peak values), Vdiode and VLOAD (Peak and dc values). Draw the input and output voltage waveforms. (Si diode) Vin: Vin rms= Vin peak = VDIODE Vdiode = 4 Vin VLOAD: VLOAD Peak =. Load VLOAD VLOAD DC= 2031 Supply wwwwww
The inductor current of a buck-boost converter is shown in the figure. The minimum inductor current is zero and the peak value is 5A. The load resistor 5 A value is equal to R=702 Assume that the output voltage ripple is 1%. All components are ideal. Determine. a) Duty ratio. b) Output voltage. c) Input voltage d) Inductor value e) Capacitor value. 12μ 20μ 32μ 40μ t,sec
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
-Design a buck converter that has an output of 12 V from an input of 18 V. The output power is 10 W. The output voltage ripple must be no more than 100 mV p-p. Specify the duty ratio, switching frequency, and inductor and capacitor values. Design for continuous inductor current.
Design a Cuk converter that has an input of 25V and the output of -30V. The load is 60W. Specify the duty ratio, switching frequency, inductor values and capacitor values. The maximum change in inductor currents must be 20 percent of the average currents. The ripple voltage across capacitor C1 must be less than 5 percent, and the output ripple voltage must be less than 1 percent.
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
6. The R-C circuit has a resistance of 100 ohms and a capacitive reactance of 150 ohms are connected in series across a A.C. voltage source. If a current of 0.9 A is flowing in the circuit determine (a) Power factor (b) Active power (c) Reactive power.
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
Design a boost converter to provide an output voltage of 36V from a 24V source. The load is 50W. The voltage ripple factor must be less than 0.5%. Specify the duty cycle ratio, switching frequency, inductor and capacitor size, and power device
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
9| Design Dc Dc converterto produced -15 V out put Prom Source Varies from 12 to 18 V. The load Resistance 15r.
An R-L load is connected to a 250 V, 400 Hz step down dc converter. The average load current is 100 A. The load resistance is 0.5 Ohm. The allowed ripple limit is 15%. The minimum value of inductor to limit the maximum ripple current is: