What are some of the reasons that some (perhaps all) of your readings do not match the calculated values? Electrochemical Cell 1. Observed Voltage: +0.859 V, Calculated Eo for cell: 1.1 V Electrochemical Cell 2. Observed Voltage: -0.379 V, Calculated Eo for cell: -0.47 Electrochemical Cell 3. Observed Voltage: +0.031 V, Calculated Eo for cell: -0.31 V Electrochemical Cell 4. Observed Voltage: +0.200 V, Calculated Eo for the cell: +0.19 V

What are some of the reasons that some (perhaps all) of your readings do not match the calculated values? Electrochemical Cell 1. Observed Voltage: +0.859 V, Calculated Eo for cell: 1.1 V Electrochemical Cell 2. Observed Voltage: -0.379 V, Calculated Eo for cell: -0.47 Electrochemical Cell 3. Observed Voltage: +0.031 V, Calculated Eo for cell: -0.31 V Electrochemical Cell 4. Observed Voltage: +0.200 V, Calculated Eo for the cell: +0.19 V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter1: Atomic Structure

Section: Chapter Questions

Problem 6RQ: How many valence electrons are generally contained in materials used for insulators?

See similar textbooks

Similar questions

What is CEMF?
How is a solid-state diode tested? Explain.
Question 3: If we assume the reverse current is -99 pA, the built-in voltage is 0.64 V, and the applied voltage Va is -26 V, what reverse R-G current in pA would we expect if the applied voltage Va is changed to -1 V. This is for an abrupt junction silicon diode at room temperature. Answer should be to three significant digits with fixed point notation. Correct Answer: -24.6
Draw the load line for the diode circuit in frontal bias if you know that the value of the external voltage is 6 volts and the load resistance is 150 ohms. Solution: To plot the load line, the following steps must be followed 1- Use Kirchhoff's voltage law to determine the voltage values of the source, resistance and diode. 2- Determining a point on the X axis that represents the maximum voltage V on both sides of the diode. (1) Solved Problems, Chapter Three: Dr. Electronic. Omar Mahidi Daoud 3- Determination of a point on the Y axis which represents the maximum value of the diode current. 4- Connect the two points with a line and this line is the load line 5- To find the slope of the load line, the formula (= m) must be used, meaning that the slope is the negative value of the reciprocal of the load resistance. RL
7. A diode conducts 1mA at 20°C. If it is operated at 100°C, what will be the current? Given data: n=1.74 and NTC value = 2.2mV/°C.
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm
State the operating voltage for Si diode and GaAs diode. Determine V., and the current across 4.7 ka resistor for the network in Figure 5 below. 12 V Si GaAs 4.7 k2 Figure 5
Find the current through the diode in the circuit shown. Assume the diode to be ideal. 50 92 www R₁ D V= 10 V = O 185 mA O 46 mA O 140 mA O 28 MA 592 wwww R₂ B
Explain how you could use an ohmmeter to identify the cathode of an unmarked diode. Why is it necessary to know the actual polarity of the ohmmeter leads? *in your own words
1. For the following circuit with an ideal diode, determine at what time the diode starts conducting (goes into the "ON" state). Assume that the resistor is R= 15002, the battery has a constant voltage of B = 10V, and the varying source is Vs = 2t – 1 volts. Enter the value of time (in seconds) without the units. R Vs BV
Current 420 ohm 30 V 1,(max) = 80 mA Voltage 2.2 kohm Vp-out 0.6 V Vp-in enonal Zener Current Answer the following question according to the above. Remember Kirchhoff's laws when making your calculations in this question. According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply?
Calculate the voltage and current of each resistance and diode in the following circuit.