Consider a process consisting of three resources. Assume there exists unlimited demandfor the product.• Resource 1 has a processing time of 6 minutes per unit.• Resource 2 has a processing time of 3 minutes per unit.• Resource 3 has a processing time of 5 minutes per unit.All three resources are staffed by one worker.a. Draw a process flow diagram of this process.b. What is the capacity of resource 2?c. What is the bottleneck in the process?d. What is the utilization of resource 2?e. How long does it take the process to produce 200 units starting with an empty system,assuming this is a worker-paced process?

Consider a process consisting of three resources. Assume there exists unlimited demandfor the product.• Resource 1 has a processing time of 6 minutes per unit.• Resource 2 has a processing time of 3 minutes per unit.• Resource 3 has a processing time of 5 minutes per unit.All three resources are staffed by one worker.a. Draw a process flow diagram of this process.b. What is the capacity of resource 2?c. What is the bottleneck in the process?d. What is the utilization of resource 2?e. How long does it take the process to produce 200 units starting with an empty system,assuming this is a worker-paced process?

Name: Consider a process consisting of three resources. Assume there exists
Uploaded: 2024-03-20T06:57:05.000Z
Channel: Bartleby
Description: Consider a process consisting of three resources. Assume there exists unlimited demandfor the product.• Resource 1 has a processing time of 6 minutes per unit.• Resource 2 has a processing time of 3 minutes per unit.• Resource 3 has a processing time

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter4: Linear Programming Models

Section: Chapter Questions

Problem 111P

See similar textbooks

Similar questions

Number of Processing Time for A Processing Time for B Processing Time for C (minutes) Resource Workers (minutes) (minutes) 1 2 2 2 4 4 5 1 15 3 2 6. 4
18/hr 4 10/hr 20/hr Current capacity 5 12/hr 19/hr 8/hr 36/hr The diagram describes a service process where customers go through either of two parallel three-step processes and then merge into a single line for two final steps. Capacities of each step are shown on the diagram. a. What is the current capacity of the entire system? units per hour Operation to improve How much additional capacity to strive for Resulting capacity of the process 8 36/hr b. If you could increase the capacity of only one operation through process improvement efforts, which operation would you select, how much additional capacity would you strive for, and what would the resulting capacity of the process be? units per hou units per hou
5 ints PA 3-9 (Algo) Consider a four-step serial process with... Consider a four-step serial process with the number of workers at each step and processing times given in the following table. Time per Customer (in Minutes) 9 11 14 6 Process Step 1 2 3 4 Number of Workers 1 5 5 3 Assuming that the process starts out empty and is worker-paced, how long will it take (in minutes) to serve 14 customers? Note: Round to nearest minute. Time taken X Answer is complete but not entirely correct. 28 x minutes
Mega Corp. is designing a product layout for a new electronic product. They plan to use this production line 8 hours a day in order to meet forecasted demand of 700 units per day. For output to meet the forecasted demand, the cycle time for this production line should be? Round-up to the nearest integer Select one: a. 64 seconds b. 42 seconds c. 32 seconds d. 38 seconds
Consider a process consisting of five resources that are operated 8 hours per day. Theprocess works on three different products, A, B, and C: Demand for the three different products is as follows: product A, 40 units per day;product B, 50 units per day; and product C, 60 units per day.a. What is the bottleneck?b. What is the flow rate for each flow unit, assuming that demand must be served in the mixdescribed above (i.e., for every four units of A, there are five units of B and six units of C)?
PA 3-9 (Algo) Consider a four-step serial process with... Consider a four-step serial process with the number of workers at each step and processing times given in the following table. Time per Customer (in Minutes) 5 14 6 3 Process Step 1 Number of Workers 1 Assuming that the process starts out empty and is worker-paced, how long will it take (in minutes) to serve 30 customers? Note: Round to nearest minute. Time taken minutes
A. What is capacity? B. Why is process capacity a limiting factor in all business processes and systems? Which one isbetter: too much capacity or too little capacity? What would be the conclusi
Esplanade Marine Parts Inc. wants to produce parts in batches of 60 parts. Each part must be processed sequentially from workstation A to B. Processing Workstation Batch Size (Q) Time per Part 40 seconds A B 60 60 15 seconds a. How many seconds are required to produce the batch under the assumptions of batch processing? Round your answer to the nearest whole number. seconds b. How many seconds are required to produce the batch under the assumptions of single-piece flow processing? Round your answer to the nearest whole number. seconds C. Compare the two solutions in terms of time saved. Round your answer to the nearest whole number. Using the assumptions of -Select- processing saves seconds.
To meet holiday demand, Penny’s Pie Shop requires a pro-duction line that is capable of producing 50 pecan pies perweek, while operating only 40 hours per week. There areonly four steps required to produce a single pecan pie withrespective processing times of 5 minutes, 5 minutes, 45 min-utes, and 15 minutes.a. What should be the line’s cycle time?b. What is the smallest number of workstations Penny couldhope for in designing the line considering this cycletime?c. Suppose that Penny finds a solution that requires onlyfour stations. What would be the efficiency of this line?
a. what is the bottleneck of this process? b. what is the hourly capacity of the process?
8. The capacity of a process is determined by A. the flow of materials. B. the maximum of the required capacity resources. C. the bottleneck. OD. throughput time O Mark for review (Will be highlighted on the review page) >
A process is scheduled to run 24 hours every weekday across 3 shifts. Each shift gets a 20-minute break. There is also a 10-minute production meeting at the start of each shift. The total operation time for 1 part is 0.8 minute. The demand for the product is 275,000 parts per week. a) Determine the TAKT time for the process and explain briefly what this means. b) Determine the number of workers required for the process.