A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm diameter solid brass (G = 37 GPa) rod. Segment (2) is a solid aluminum (G = 26 GPa) rod. Determine the minimum diameter of the aluminum segment if the rotation angle at C relative to support A must not exceed 3°. T= 60 N.m (1) (2) A C 1,800 mm 800 mm Select one: a. 14.87 mm O b. 29.75 mm O . 12.24 mm O d. 24.48 mm O e. 32.00 mm O f. None

A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm diameter solid brass (G = 37 GPa) rod. Segment (2) is a solid aluminum (G = 26 GPa) rod. Determine the minimum diameter of the aluminum segment if the rotation angle at C relative to support A must not exceed 3°. T= 60 N.m (1) (2) A C 1,800 mm 800 mm Select one: a. 14.87 mm O b. 29.75 mm O . 12.24 mm O d. 24.48 mm O e. 32.00 mm O f. None

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the angle of rotation in radians.
A steel shaft with a length of 3.00 m. One meter of the steel is contained in a brass tube and firmly attached. The diameter d1 = 70 mm and the diameter d2 = 90 mm. Brass G = 39GPa and steel G = 77.20 GPa. Determine: The torque that can be applied if the deformation at one end is 10 degrees. Answer: T = 8.64 kN – m The torque that can be applied if the maximum shear stress in brass is 70MPa and in steel is 110MPa. Answer: T = 6.352 kN – m Recommendation: analyze by segments. The first segment is only brass, then the composite part between brass and steel, and the last part only steel. In the composite segment, use only one material. In this same segment, equalize the deformations.
The shaft shown has two pulleys, where pulley C is the input and pulley A is the output. The shaft is supported by frictionless bearings at points O and B. The pulley diameters are dA = 361 mm and dc = 224 mm. The input tensions on pulley Care T3 = 267 N and T4 = 0.10*T3. The shaft diameter, ds = 25 mm. T₁ da ХОА 1₂ oo ds B dc T3 XAB XBC T₁ • What is the tension T₁ on the output pulley (in N)? Assume the lower tension is 10% of the higher tension.
The copper pipe has an outer diameter of 2.5 in. and an inner diameter of 2.25 in. It is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown.(Figure 1) Points A and B lie on the pipe's outer surface. Figure C B |--M 2 ft V 150 lb-ft/ft. TIM A 2 ft V -- < 1 of 1 Determine the shear stress at point A. Express your answer to three significant figures and include appropriate units. TA = ΤΑ Submit Part B O — μA 4 TB = Value Units Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining μA P Determine the shear stress at point B. Express your answer to three significant figures and include appropriate units. Value Units ? www ? Submit Previous Answers Request Answer
Problem 2. The assembly consists of three titanium (Ti- 6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 6 kip is applied to the ring F, determine the horizontal displacement of point F, and determine the angle of tilt of rigid bar AC. B D 4 ft ACD = 1 in² AAB 6 ft 1.5 in² E 2 ft 1 ft 1 ft AEF = 2 in² 6 kip
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by k = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(1) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is J, = 0.05 kg-m?. Assuming the equivalent torsional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 0(1). O(1) M(1) = Mg cos etr %3! Turbine rotor, Jo
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by ka = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(t) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rads. The mass moment of inertia of the rotor about the shaft axis is Jo = 0.05 kg-m. Assuming the equivalent torsional damping constant of the system as c, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 6(1). O(1) ke M(1) = M, cos ot Turbine rotor, Jo
1. The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the driver gear acts at a pressure angle of 20 degree. The shaft transmits a torque to point A of TA =340 N.m. The shaft is machined from steel with S,=420 MPa, Km2.5, S=134MPA and N=2. Draw shear and bending diagrams and calculate diameter of shaft. 250 mm 100 mm
The assembly shown consists of the solid steel shaft (1) with a diameter of D₁ = 14 in and a copper tube (2) with an outside diameter of D₂ = 7.5 in. and a wall thickness of t₂ = 0.35 in. The assembly carries a torque of TB = 68 kip-ft at joint B and a torque of Tc = 14 kip-ft at point C. [D₁ = 14 in., D₂ = 7.5 in., t₂ = 0.35 in., TB = 68 kip-ft, Tc = 14 kip-ft] Tc 00000 A -13.8 ksi -11.28 ksi -6.25 ksi -15.83 ksi -7.5 ksi (1) Answer: L₁ L₂ What is the maximum shear stress in the tube (2)? B (2) C What is the maximum shear stress in the shaft (1)? ksi
Problem (4): (1) T= 50 N-m B 1,800 mm 800 mm A single torque of T = 50 N-m is applied to a compound torsion member. Segment (1) is a 32-mm diameter solid brass (G = 37 GPa) rod. Segment (2) is a solid aluminum (G = 26 GPa) rod. %3D %3D Determine the minimum diameter of the aluminum segment if the rotation angle at C relative to support A must not exceed 3°.
2. A shaft is designed to carry torque as shown below. The shaft consists of a steel rod which is fixed against rotation at both ends. In addition, the left half of the rod is well bonded to an aluminum sleeve. The assembly is loaded by a torque of 2000 N-m as shown. - The steel rod has shear modulus G = 80 GPa and radius r= 1.5 cm (hence polar moment of inertia Ip = 7.95 x 108 m². The aluminum sleeve has shear modulus G = 26 GPa, outer radius 2.6 cm and inner radius 1.5 cm (hence polar moment of inertia I, = 7.95 x 108 m²). 2000 N sleeve -0.57 rod a. Calculate the total reaction torques at the two walls (points A and C). b. Calculate the maximum shear stresses in the steel rod and the aluminum sleeve. c. Calculate the angle of twist at point B.
The diameter of and LcD = 240 mm. 1. The lengths LAB = LBC = 200 mm parts AB and CD of the bar is 25 mm and the diameter of part BC is 50 mm. The shear modulus of the material is G = 80 GPa. If the torque T = 2.2 kN- m, determine the magnitude of the angle of twist of the right end of the bar relative to the wall in degrees. 4 kN-m 8 kN-m LAB. LBC. 2. The lengths LAB = LBC = 200 mm and LCD = 240 mm. The diameter of parts AB and CD of the bar is 25 mm and the diameter of part BC is 50 mm. The shear modulus of the material is G = 80 GPa. What value of the torque T would cause the angle of twist of the right end of the bar relative to the wall to be zero? 4 kN-m 8 kN-m LAB. T LBC