A circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60 Mpa. Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1=10kN-m and T2=25kN-m. Answer in mm. A circular solid shaft made of vibranium has G=80 MPa and has a limiting torsional shear stress of 60 MPa.Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1-10 kN-m and T2-25 kN-m.Answer in mm.T1Tpf-1.5 m 2.5 m1 m

Answered: Image /qna-images/answer/554d2c98-7ac6-415d-b34f-6f68432cd30b.jpg

circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60 Mpa. Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1=10kN-m and T2=25kN-m. Answer in mm.

circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60 Mpa. Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1=10kN-m and T2=25kN-m. Answer in mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 66-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and concentrated torsional loadings shown where T = 1.50 kN-m. (Figure 1) Figure Part A 0.4m 0.6 m 2 kN-m/m Determine the angle of twist at the free end A of the shaft. Express your answer in degrees to three significant figures. A 1 of 1 4
1. The 12 kN m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of the shaft is to be limited to 3°. (a) Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use G = 83 GPa for steel. 2. The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 59 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 84 MPa. If a torque of Tc=29400 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = d₂ = i (2) B A mm mm
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 68 mm and G = 34.84 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.59 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 69.92 MPa in the bronze and 87.06 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b.
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.
two solid steel shafts of different diameters are joined together at point C. the diameter of the smaller shaft is 0.5 in, while the diameter of the larger shaft is 1 in. if the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi.Show full solution please
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 72 mm and G = 30.49 GPa. For the steel segment BC, the diameter is 48 mm and G = 83.57 GPa. Given that a = 2.09 m and b = 1.48 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 66.49 MPa in the bronze and 85.69 MPa in the steel. Round off the final answer to two decimal places.
A tapered, wrought iron shaft of length 5 ft, has 2 inch diameter at the fixed end and 0.8 inch diameter at the free end. Determine the angle of twist of the shaft, if it carries a torque, T = 2000 lb-in at the free end. Use G = 10^7 psi for wrought iron.
The motor delivers a torque of T-60 Nm to the shaft AB. This torque is transmitted to shaft CD using the gears at E and F. The bearings BC, and D allow free rotation of the shafts Figure 50 mm, 30 mm B 35 mm 125 mm 1 of 12 ▾ Determine the maximum shear stress in AB shaft Express your answer with the appropriate units. (TA) 1.415. Submit Part C X Incorrect: Try Again: 5 attempts remaining MPa Previous Answers Request Answer Determine the maximum shear stress in CD shalt Express your answer with the appropriate units. (CD) 2.227 Submit MPa Previous Answers Request Answer ? ?
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 70 mm and G = 33.29 GPa. For the steel segment BC, the diameter is 40 mm and G = 84.85 GPa. Given that a = 2.03 m and b = 1.38 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.59 MPa in the bronze and 84.39 MPa in the steel. Round off the final answer to two decimal places. d A Bronze B Steel b. Add your answer
2. A composite shaft is subjected to two torques as shown below. Shaft AB is a solid aluminum (G = 25 GPa) shaft and is welded to brass (G = 37 GPa) shaft BCD. Segment BC of the brass shaft is solid and the segment CD is hollow with inner diameter of 40 mm. Determine the maximum shear stresses in the aluminum and brass shafts, and the angle of twist of end A. 60 mm T = 1600 N - m 36 mm TA = S00 N - m 250 mm 375 mm 400 mm
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 30mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120MPa and it's angle of twist is limited to 7deg. Use G=83GPa for steel. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.