A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 4090 N-m.The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.0-m length of shaft.O 0.0755 radO 0.1029 radO 0.0637 radO 0.0561 radO 0.0797 rad

The given values are - do =75 mm, t=5 mm, T =4090×1000 Nmm, G =80×1000 Mpa, L=2000mm The inside…

Answered: A hollow steel shaft with an outside…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.5P: A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions...

See similar textbooks

Similar questions

A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A solid circular steel shaft having an outside diameter of 1.75 in. is subjected to a pure torque of T = 8130 lb-in. The shear modulus of the steel is G = 12,000 ksi. Determine the magnitude of the angle of twist in a 6.00-ft length of shaft. O 0.0338 rad O 0.0382 rad O 0.0530 rad O 0.0573 rad O 0.0430 rad
A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
3. The two identical shafts, 1 and 2, are built into supports at their left ends. Gears mounted on their right ends engage a third gear that is attached to shaft 3. Determine the torques in shafts 1 and 2 when the 500N -m torque is applied to shaft 3. 40 500 Nm 80 Dimensions in mm 4. A 4-ft-long tube with the cross section shown in the figure is made of aluminum. Find the torque that will cause a maximum shear stress of 10 000 psi. Use G = 4 x 106 psi for aluminum. +4 in. → 0.04 in. 0.08 in.´ 5. Two steel springs are arranged in series as shown. The upper spring has 36 turns of 100-mm- diameter wire on a mean radius of 350 mm. The lower spring consists of 24 turns of 75-mm diameter wire on a mean radius of 245 mm. If the ultimate shearing stress in either spring must not exceed 692 MPa, (a) compute the maximum value of P and total elongation using factor of safety equal to 1.5. (b) What is the equivalent spring constant? Use G = 83 GPa. 2 of 2 4 in. wwwww.-
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.
A constant torque of 75 lb-in. is applied to the circular rod below, with a radius of 2 in. The shear modulus G = 3.5 x 106 psi. What is the angle of twist, p, at the end of the 6 foot long rod? 0.117 rad 0.056 rad 0.234 rad 0.314 rad T
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
The dimensions of the cross section of an airplane fuselage are shown in figure 1. If the fuselage is subjected to a torque of 8 MN-m, determine the maximum shear stress and twist per unit length of the fuselage. The thickness of the wall is 3 mm. Take the G for curved walls as 25000 N/mm and for the straight walls as 27500 N/mm². 09 m 1.35 m 09 m Figure 1
A solid circular steel shaft having an outside diameter of 2.25 in. is subjected to a pure torque of T = 9060 Ib-in. The shear modulus of the steel is G = 12,000 ksi. Determine the maximum shear stress in the shaft. O 3.31 ksi O 5.15 ksi O 4.05 ksi 3.82 ksi O 2.53 ksi
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a wall thickness of 9 mm. Segment (2) has an outside diameter of 139 mm and a wall thickness of 11 mm. The shaft is subjected to torques TB = 47 kN-m and Tc = 24 kN-m, which act in the directions shown. Determine the maximum shear stress magnitudes 7₁, 72 in each shaft segment. Answers: T1 = i T2 = i (1) (2) MPa. MPa.
A hollow circular steel shaft with an outside diameter of 2.569. and a wall thickness of 0.388 in. is subjected to a pure torque of 292 lb-ft. The shaft is 124 in. long. The shear modulus of the steel is G-12.000 ksi. Determine the magnitude of the angle of twist in the shaft. 1. T B
A tapered, wrought iron shaft of length 5 ft, has 2 inch diameter at the fixed end and 0.8 inch diameter at the free end. Determine the angle of twist of the shaft, if it carries a torque, T = 2000 lb-in at the free end. Use G = 10^7 psi for wrought iron.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS