Physics for Scientists and Engineers: Foundations and Connections
1st Edition
ISBN: 9781133939146
Author: Katz, Debora M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 14, Problem 65PQ
To determine
The average strain in the beam during the impact.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The 465-kg uniform I-beam supports the load shown. Determine the reactions at the supports.
Answers:
Ax=
Ay=
By=
i
-5.9 m-
3.1 m
200 kg
zzz
A box of negligible mass rests at the left end of a
2.00 m, 29.0 kg plank (Eigure 1). The width of the box
is 75.0 cm, and sand is to be distributed uniformly
throughout it. The center of gravity of the nonuniform
plank is 50.0 cm from the right end.
Figure
Sandbox-
75.0 cm
A
1
▼
Part A
What mass of sand should be put into the box so that the plank balances horizontally on a fulcrum placed just
below its midpoint?
Express your answer with the appropriate units.
msand =
Submit
μA
Value
Request Answer
Units
h
Review | Constants
?
The beam is made of an elastic-plastic material for which σYσYsigma_Y = 70 MPaMPa . The largest moment in the beam occurs within the center section a-a.
Determine the magnitude of each force PP that causes this moment to be the largest elastic moment.
Determine the magnitude of each force PP that causes this moment to be the largest plastic moment.
Chapter 14 Solutions
Physics for Scientists and Engineers: Foundations and Connections
Ch. 14.1 - A rubber duck floats in a bathtub. Imagine moving...Ch. 14.1 - Prob. 14.2CECh. 14.2 - CASE STUDY Hanging a Plane from a Single Point In...Ch. 14.2 - Prob. 14.4CECh. 14.4 - Imagine two vertical rods initially of equal...Ch. 14 - What Is Static Equilibrium? Problems 13 are...Ch. 14 - Prob. 2PQCh. 14 - Two identical balls are attached to a...Ch. 14 - While working on homework together, your friend...Ch. 14 - Consider the sketch of a portion of a...
Ch. 14 - Prob. 6PQCh. 14 - Prob. 7PQCh. 14 - Prob. 8PQCh. 14 - The keystone of an arch is the stone at the top...Ch. 14 - Prob. 10PQCh. 14 - Stand straight and comfortably with your feet...Ch. 14 - Prob. 12PQCh. 14 - Prob. 13PQCh. 14 - Prob. 14PQCh. 14 - Prob. 15PQCh. 14 - Prob. 16PQCh. 14 - Prob. 17PQCh. 14 - Prob. 18PQCh. 14 - Prob. 19PQCh. 14 - Prob. 20PQCh. 14 - Prob. 21PQCh. 14 - The inner planets of our solar system are...Ch. 14 - Two Boy Scouts, Bobby and Jimmy, are carrying a...Ch. 14 - Prob. 24PQCh. 14 - A painter of mass 87.8 kg is 1.45 m from the top...Ch. 14 - Consider the situation in Problem 25. Tests have...Ch. 14 - Children playing pirates have suspended a uniform...Ch. 14 - Prob. 28PQCh. 14 - Prob. 29PQCh. 14 - A 5.45-N beam of uniform density is 1.60 m long....Ch. 14 - A wooden door 2.1 m high and 0.90 m wide is hung...Ch. 14 - A 215-kg robotic arm at an assembly plant is...Ch. 14 - Problems 33 and 34 are paired. One end of a...Ch. 14 - For the uniform beam in Problem 33, find the...Ch. 14 - Prob. 35PQCh. 14 - A square plate with sides of length 4.0 m can...Ch. 14 - Prob. 37PQCh. 14 - At a museum, a 1300-kg model aircraft is hung from...Ch. 14 - A uniform wire (Y = 2.0 1011 N/m2) is subjected...Ch. 14 - A brass wire and a steel wire, both of the same...Ch. 14 - In Example 14.3, we found that one of the steel...Ch. 14 - A carbon nanotube is a nanometer-scale cylindrical...Ch. 14 - A nanotube with a Youngs modulus of 1.000 1012 Pa...Ch. 14 - Consider a nanotube with a Youngs modulus of 2.130...Ch. 14 - Prob. 45PQCh. 14 - Use the graph in Figure P14.46 to list the three...Ch. 14 - Prob. 47PQCh. 14 - A company is testing a new material made of...Ch. 14 - Prob. 49PQCh. 14 - Prob. 50PQCh. 14 - Prob. 51PQCh. 14 - Prob. 52PQCh. 14 - Prob. 53PQCh. 14 - Prob. 54PQCh. 14 - Prob. 55PQCh. 14 - Prob. 56PQCh. 14 - A copper rod with length 1.4 m and cross-sectional...Ch. 14 - Prob. 58PQCh. 14 - Prob. 59PQCh. 14 - Bruce Lee was famous for breaking concrete blocks...Ch. 14 - Prob. 61PQCh. 14 - Prob. 62PQCh. 14 - Prob. 63PQCh. 14 - A One end of a metal rod of weight Fg and length L...Ch. 14 - Prob. 65PQCh. 14 - A steel cable 2.00 m in length and with...Ch. 14 - Prob. 67PQCh. 14 - Prob. 68PQCh. 14 - Prob. 69PQCh. 14 - Prob. 70PQCh. 14 - Prob. 71PQCh. 14 - Prob. 72PQCh. 14 - Prob. 73PQCh. 14 - We know from studying friction forces that static...Ch. 14 - Ruby, with mass 55.0 kg, is trying to reach a box...Ch. 14 - An object is being weighed using an unequal-arm...Ch. 14 - Prob. 77PQCh. 14 - A massless, horizontal beam of length L and a...Ch. 14 - A rod of length 4.00 m with negligible mass is...Ch. 14 - A rod of length 4.00 m with negligible mass is...Ch. 14 - A horizontal, rigid bar of negligible weight is...Ch. 14 - Prob. 82PQCh. 14 - Prob. 83PQCh. 14 - Prob. 84PQCh. 14 - Prob. 85PQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- At a museum, a 1300-kg model aircraft is hung from a lightweight beam of length 12.0 m that is free to pivot about its base and is supported by a massless cable (Fig. P14.38). Ignore the mass of the beam. a. What is the tension in the section of the cable between the beam and the wall? b. What are the horizontal and vertical forces that the pivot exerts on the beam? FIGURE P14.38 (a) From the free-body diagram, the angle that the string tension makes with the beam is = 55.0 + 18.0 = 73.0, and the perpendicular component of the string tension is FT sin73.0. Summing torques around the base of the rod gives (Eq. 14.2): =0:(12.0m)(1300kg)(9.81m/s2)cos55.0+FT(12.0m)sin73.0=0FT=(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0FT=7.65103N Figure P14.38ANS (b) Using force balance (Eq. 14.1): Fx=0:FHFTcos18.0=0FH=FTcos18.0=[(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0]cos18.0=7.27103NFy=0:FVFTsin18.0(1300kg)(9.81m/s2)=0 FV=FTsin18.0+(1300kg)gFV=[(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0]sin18.0+(1300kg)(9.81m/s2)FV=1.51104Narrow_forwardConsider a nanotube with a Youngs modulus of 2.130 1012 N/m2 that experiences a tensile stress of 5.3 1010 N/m2. Steel has a Youngs modulus of about 2.000 1011 Pa. How much stress would cause a piece of steel to experience the same strain as the nanotube?arrow_forwardRuby, with mass 55.0 kg, is trying to reach a box on a high shelf by standing on her tiptoes. In this position, half her weight is supported by the normal force exerted by the floor on the toes of each foot as shown in Figure P14.75A. This situation can be modeled mechanically by representing the force on Rubys Achilles tendon with FA and the force on her tibia as FT as shown in Figure P14.75B. What is the value of the angle and the magnitudes of the forces FA and FT? FIGURE P14.75arrow_forward
- A uniform beam of length 7.60 m and weight 4.50 102 N is carried by two workers, Sam and Joe, as shown in Figure P12.6. Determine the force that each person exerts on the beam. Figure P12.6arrow_forwardA massless, horizontal beam of length L and a massless rope support a sign of mass m (Fig. P14.78). a. What is the tension in the rope? b. In terms of m, g, d, L, and , what are the components of the force exerted by the beam on the wall? FIGURE P14.78arrow_forwardA 215-kg robotic arm at an assembly plant is extended horizontally (Fig. P14.32). The massless support rope attached at point B makes an angle of 15.0 with the horizontal, and the center of mass of the arm is at point C. a. What is the tension in the support rope? b. What are the magnitude and direction of the force exerted by the hinge A on the robotic arm to keep the arm in the horizontal position? FIGURE P14.32arrow_forward
- An aluminum wire is 0.850 m long and has a circular cross section of diameter 0.780 mm. Fixed at the top end, the wire supports a 1.20-kg object that swings in a horizontal circle. Determine the angular speed of the object required to produce a strain of 1.00 × 10-3.arrow_forwardA P8.11 SL: dir Find the x and y coordinates of the center of gravity of a 4.00 ft by 8.00 ft uniform sheet of plywood with the upper right quadrant removed as shown in the following figure. Hint: The mass of any segment of the plywood sheet is proportional to the area of that segment. y (ft) 4.00 2.00 x(ft) 0- 0 4.00 6.00 8.00 2.00arrow_forwardFlying Circus of Physics The figure shows an approximate plot of stress versus strain for a spider-web thread, out to the point of breaking at a strain of 2.20. The vertical axis scale is set by a = 0.190 GN/m²,b = 0.300 GN/m², and c = 0.720 GN/m². Assume that the thread has an initial length of 0.720 cm, an initial cross-sectional area of 4.00 x 10-12 m², and (during stretching) a constant volume. The strain on the thread is the ratio of the change in the thread's length to that initial length, and the stress on the thread is the ratio of the collision force to that initial cross-sectional area. Assume also that when the single thread snares a flying insect, the insect's kinetic energy is transferred to the stretching of the thread. (a) How much kinetic energy would put the thread on the verge of breaking? What is the kinetic energy of (b) a fruit fly of mass 7.50 mg and speed 2.00 m/s and (c) a bumble bee of mass 0.370 g and speed 0.800 m/s? Would (d) the fruit fly and (e) the bumble…arrow_forward
- ASAParrow_forwardAn 12.2-kg stone at the end of a steel (Young's modulus 2.0 x 1011 N/m2) wire is being whirled in a circle at a constant tangential speed of 17.9 m/s. The stone is moving on the surface of a frictionless horizontal table. The wire is 3.67 m long and has a radius of 4.99 x 10-3 m. Find the strain in the wire.arrow_forwardReview Problem. A 36.0 kg hammer strikes a steel spike 2.20 cm in diameter while moving with speed of 22.0 m/s. The hammer rebounds with speed 11.0 m/s after 0.110 s. What is the average strain in the spike during the impact? (a) What is the approximate magnitude of force (in N) a martial arts instructor uses to break a board if her hand's speed at time of impact is 10.5 m/s and decreasing to 1.05 m/s during a 0.00200 s time-of-contact with the board? The mass of her hand and arm is 1.15 kg. (b) Estimate the shear stress (in N/m2), assuming this force is exerted on a 1.00 cm-thick pine board that is 10.0 cm wide. | N/m² (c) If the maximum shear stress the board can support before breaking is 3.60 x 106 N/m2, will the board break? Yes No O Oarrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Static Equilibrium: concept; Author: Jennifer Cash;https://www.youtube.com/watch?v=0BIgFKVnlBU;License: Standard YouTube License, CC-BY