Concept explainers
A 60-kg motor sits on four cylindrical rubber blocks. Each cylinder has a height of 3.0 cm and a cross-sectional area of 15
(a)
The distance moved by the rubbers along sideways if a sideways force of
Answer to Problem 44SP
Solution:
Explanation of Solution
Given data:
There are four cylindrical rubber blocks and a
The sideway force on the motor is
The height of the cylinder is
The cross-sectional area of the cylinder is
The shear modulus of the rubber is
Formula used:
Write the expression for Young’s modulus
Here,
Explanation:
Understand that the rubber blocks are at the same distance from the sideways force. Therefore, the force will equally be distributed to each rubber blocks.
Therefore, the forcesacting on each block is as follows:
Recall the expression for Young’s modulus
Substitute
Conclusion:
The distance moved due to the sideways force is
(b)
The frequency with which the
Answer to Problem 44SP
Solution:
Explanation of Solution
Given data:
There are four cylindrical rubber blocks and a
The sideway force on the motor is
The height of the cylinder is
The area of the cylinder is
The shear modulus of the rubber is
The mass of the motor is
Formula used:
Write the expression for spring constant:
Here,
Write the expression for frequency:
Here,
Explanation:
The forces that causes the back and forth motion is equivalent to the total forces acting as the sideways force of
Recall the expression for equivalent spring constant:
Here,
Substitute
Recall the expression for frequency:
Substitute
Conclusion:
The frequency of the motor with which itvibrates back and forth is
Want to see more full solutions like this?
Chapter 12 Solutions
Schaum's Outline of College Physics, Twelfth Edition (Schaum's Outlines)
- A uniform wire (Y = 2.0 1011 N/m2) is subjected to a longitudinal tensile stress of 4.0 107 N/m2. What is the fractional change in the length of the wire?arrow_forwardA horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81arrow_forwardA 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?arrow_forward
- A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?arrow_forwardIn Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?arrow_forwardWhat Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong, lightweight rod (Fig. P14.1). The rod is supported by a horizontal pin near the top. The ball is at rest. Is the ball in static equilibrium? If not, why not? If so, which type of equilibrium is itstable, unstable, or neutral? Hint: What would happen if you displaced the ball slightly? FIGURE P14.1arrow_forward
- Why is the following situation impossible? A worker in a factory pulls a cabinet across the floor using a rope as shown in Figure P12.36a. The rope make an angle = 37.0 with the floor and is tied h1 = 10.0 cm from the bottom of the cabinet. The uniform rectangular cabinet has height = 100 cm and width w = 60.0 cm, and it weighs 400 N. The cabinet slides with constant speed when a force F = 300 N is applied through the rope. The worker tires of walking backward. He fastens the rope to a point on the cabinet h2 = 65.0 cm off the floor and lays the rope over his shoulder so that he can walk forward and pull as shown in Figure P12.36b. In this way, the rope again makes an angle of = 37.0 with the horizontal and again has a tension of 300 N. Using this technique, the worker is able to slide the cabinet over a long distance on the floor without tiring. Figure P12.36 Problems 36 and 44.arrow_forwardA copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57arrow_forwardConsider the sketch of a portion of a roller-coaster track seen in Figure P14.5. Identify places on the track that could be considered possible locations of static equilibrium for a rollercoaster car were the car to be placed at any spot on the track.Which places are candidate locations for stable, unstable, andneutral static equilibrium? FIGURE P14.5arrow_forward
- Consider a nanotube with a Youngs modulus of 2.130 1012 N/m2 that experiences a tensile stress of 5.3 1010 N/m2. Steel has a Youngs modulus of about 2.000 1011 Pa. How much stress would cause a piece of steel to experience the same strain as the nanotube?arrow_forwardAlarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?arrow_forwardA 60kg motor sits on four cylindrical rubber blocks. Each cylinder has a height of 3.0 cmand a cross-sectional area of 15 cm^2. The shear modulus for this rubber is 2.0 MPa (a) If a sideways force of 300 Nis applied to the motor, how far will it move sideways? Answer: 0.075cm (b) With what frequency will the motor vibrate back and forth sideways if disturbed? Answer: 13Hzarrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning