The student runs an experiment on a cylindrical wire of a length l of 2 centimeters and the cross- sectional area A of the wire is 6.1 centimeters-squared. The measurements of the Current is as below Dataset Voltage (Applied, Volts) Current (Measured, Amperes) 0.213 0.638 0.106 7. 1.489 6. 1.915 11 2.340 13 2.766 According to the results of the experiment, what is the Resistivity p (ohm-meters) of that conducting wire? Note: Submit your answer to the third decimal point -e.g.: 0.123456 -> 0.123

The student runs an experiment on a cylindrical wire of a length l of 2 centimeters and the cross- sectional area A of the wire is 6.1 centimeters-squared. The measurements of the Current is as below Dataset Voltage (Applied, Volts) Current (Measured, Amperes) 0.213 0.638 0.106 7. 1.489 6. 1.915 11 2.340 13 2.766 According to the results of the experiment, what is the Resistivity p (ohm-meters) of that conducting wire? Note: Submit your answer to the third decimal point -e.g.: 0.123456 -> 0.123

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter28: Current And Resistance

Section: Chapter Questions

Problem 69PQ

See similar textbooks

Similar questions

sq 4. Maximum surface resistance. Consider a square sheet of side L, thickness d, and electrical resistivity p. The resistance measured between opposite edges of the sheet is called the surface resistance: R = pL/ Ld = p/d, which is independent of the area of the sheet. (R is called the resistance per square and is expected in ohms per square, because p/d has the dimensions of ohms.) If we express p by p=m/ne²t, then Rq=m/ndet. Suppose now that the minimum value of the collision time is determined by scattering from surfaces of the sheet, so that Td/v, where v is the Fermi velocity. Thus the maximum surface resistivity is Rmvp/nd²e². Show for a monatomic metal sheet one atom thickness that sq Rħ/e² = 4.1k, where lkn is 10³ ohms. sq
The voltage V (volts), current I (amperes), andresistance R (ohms) of an electric circuitare related by the equation V = IR. Suppose that V is increasing atthe rate of 1 volt/sec while I is decreasing at the rate of 1/3 amp/sec. Let t denote time in seconds. What is the value of dV/dt?
The voltage V (volts), current I (amperes), andresistance R (ohms) of an electric circuitare related by the equation V = IR. Suppose that V is increasing atthe rate of 1 volt/sec while I is decreasing at the rate of 1/3 amp/sec. Let t denote time in seconds. What equation relates dR/dt to dV/dt and dI/dt?
In the last column in the data table, it says that it's about voltage(v) divided by current(A) is equal to ohms so V/A = ohms. So if it's V/A and if you divide them to get the slope it's (y2-y1)/(x2-x1) then shouldn't V be the y value and A be the x value? And can you also try to use a line of best bit instead of drawing the line through each dot?
mobile battery during a charge cycle are shown in 1.26 The voltage and current at the terminals of an auto- Fig. P1.26. a) Calculate the total charge transferred to the battery. b) Calculate the total energy transferred to the battery. Figure P1.26 v (V) bnohostib 24 Loiwollol sd lo 16 8- 8. 12 16 20 t (ks) i (A) maxi 24 16 8- the che 4 8. 12 16 20 t (ks)
1.15 When a car has a dead battery, it can often be started by connecting the battery from another car across its terminals. The positive terminals are connected together as are the negative terminals. The connec- Si tion is illustrated in Fig. P1.15. Assume the current i in Fig. P1.15 is measured and found to be 40 A. a) Which car has the dead battery? b) If this connection is maintained for 1.5 min, how much energy is transferred to the dead battery? Figure P1.15 12V 12V
The resistance R of a conductor of length L and area of cross – section A carrying a current I is given by: a) R=pA/L, where p=specific resistance b) R = VI, where V = potential different c) R = σA, where σ = electrical conductivity d) R = 2mL/ne 2 τA. Where τ = relaxation time, n the electron density e the electronic charge and m is the mass of an electron
1.9. A block of conductor has the dimensions Lo x 2Lo x 4Lo. As shown in the figure below, the same battery is connected across the conductor in three different configurations. Which configuration draws the smallest current from the battery? All configurations draw equal current. 21 Lo 4Lo 4LO (a) (b) (c) (d)
A metallic wire with resistance 8 0, crosS-sectional area 8.2x10 m², and conductivity o= 5.81×10 0 m mV/m) inside the wire is; -1 is connected to a battery of & = 14 V. The electric field E (in 3.
A 5 strand conductor is arranged in a cross. Find the Area (in cmil) of the wire if inner radius is 2 mm. Note: Outside diameter of the biggest circle is 12 mm
The drift speed of charge carriers in a conductor carrying current / is ngA where n is the number of mobile charge carriers per unit volume, q is the magnitude of the charge on each carrier, and A is the cross-sectional area of the conductor. The transmission line has a diameter of 2.00 cm so that its radius is r= 1.00 cm = 1.0 x 10 m and so that its cross-sectional area is A = nr? - n(1.0 x 10-2 m)² = n x 10-4 m2. In metallic conductors, the mobile charge carriers are electrons, each with a charge of magnitude q- e. We are given the density n of free electrons in this copper material per unit volume. Thus, the drift speed of the electrons is V = ngA c) x 1028 m-1.60 x 10-19 C)(T x 10-4 m2) x 10 m/s.
Q1/ A piece of resistance wire, 15.6 m long and of cross-sectional area 12 mm? at temperature of 0°C, passes a current of 7.9 A when connected to d.c. supply at 240 V. Calculate (a) resistivity of the wire, (b) the current which will flow when the temperature rises to 55 °C. The temperature coefficient of the resistance wire is 0.00029 / °C.