The voltage V (volts), current I (amperes), andresistance R (ohms) of an electric circuitare related by the equation V = IR. Suppose that V is increasing atthe rate of 1 volt/sec while I is decreasing at the rate of 1/3 amp/sec. Let t denote time in seconds. What equation relates dR/dt to dV/dt and dI/dt?

The voltage V (volts), current I (amperes), andresistance R (ohms) of an electric circuitare related by the equation V = IR. Suppose that V is increasing atthe rate of 1 volt/sec while I is decreasing at the rate of 1/3 amp/sec. Let t denote time in seconds. What equation relates dR/dt to dV/dt and dI/dt?

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter1: Units And Measurement

Section: Chapter Questions

Problem 83AP: A marathon runner completes a 42.188-km course in 2 h, 30 min, and 12s. There is an uncertainty of...

See similar textbooks

Similar questions

The voltage V (volts), current I (amperes), andresistance R (ohms) of an electric circuitare related by the equation V = IR. Suppose that V is increasing atthe rate of 1 volt/sec while I is decreasing at the rate of 1/3 amp/sec. Let t denote time in seconds. What is the value of dV/dt?
sq 4. Maximum surface resistance. Consider a square sheet of side L, thickness d, and electrical resistivity p. The resistance measured between opposite edges of the sheet is called the surface resistance: R = pL/ Ld = p/d, which is independent of the area of the sheet. (R is called the resistance per square and is expected in ohms per square, because p/d has the dimensions of ohms.) If we express p by p=m/ne²t, then Rq=m/ndet. Suppose now that the minimum value of the collision time is determined by scattering from surfaces of the sheet, so that Td/v, where v is the Fermi velocity. Thus the maximum surface resistivity is Rmvp/nd²e². Show for a monatomic metal sheet one atom thickness that sq Rħ/e² = 4.1k, where lkn is 10³ ohms. sq
mobile battery during a charge cycle are shown in 1.26 The voltage and current at the terminals of an auto- Fig. P1.26. a) Calculate the total charge transferred to the battery. b) Calculate the total energy transferred to the battery. Figure P1.26 v (V) bnohostib 24 Loiwollol sd lo 16 8- 8. 12 16 20 t (ks) i (A) maxi 24 16 8- the che 4 8. 12 16 20 t (ks)
1.15 When a car has a dead battery, it can often be started by connecting the battery from another car across its terminals. The positive terminals are connected together as are the negative terminals. The connec- Si tion is illustrated in Fig. P1.15. Assume the current i in Fig. P1.15 is measured and found to be 40 A. a) Which car has the dead battery? b) If this connection is maintained for 1.5 min, how much energy is transferred to the dead battery? Figure P1.15 12V 12V
Problems A12 1-1. (a) List the SI units of length, mass, time, electric cur- rent, temperature, and amount of substance. Write the abbre- viation for each. Jund juod (b) Write the units and symbols for frequency, force, pres- and power. sure, energy, 1-2. Write the name and number represented by each abbre- viation. For example, for kW you should write kW = kilowatt = 10³ watts. (a) mW (b) pm (c) ΚΩ (d) μC (e) TJ (f) ns (g) fg (h) dpa 163. Express the following quantities with abbreviations for units and prefixes from Tables 1-1 through 1-3: (a) 10-¹3 joules0 + (1)0,HE (b) 4.317 28 x 10-8 coulombs (d) 10-10 meters (e) 2.1 x 10¹3 watts (f) 48.3 x 10-20 moles (c) 2.997 9 x 10¹4 hertz bns M2.01 1-4. Table 1-4 states that 1 horsepower = 745.700 watts. Consider a 100.0-horsepower engine. Express its power output in (a) watts; (b) joules per second; (c) calories per second; (d) calories per hour. 1-5 (a) Refer to Table 1-4 and calculate how many meters are in 1 inch. How many inches are in 1…
Ohm's law for electrical circuits like the one shown in the figure states that V=RI. In this equation, V is a constant voltage, I is the current in amperes, and R is the resistance in ohms. Your firm has been asked to supply the resistors for a circuit in which V will be 240 volts and I is to be 10±0.1 amp. In what interval does R have to lie for I to be within 0.1 amp of the value I0=10?
An electric current in a conductor varies with time according to the expression I(t) = 100 sin (120πt), where I is in amperes and t is in seconds. What is the total charge passing a given point in the conductor from t = 0 to t = (1)/(240) s?
Electric power is defined by the equation P= VI, where P stands for power, V stands for voltage, and I stands for current. Using Ohm's law, V = IR, we can substitute this for voltage in the original equation for power to write the equation for electric power in terms of current: P =I°R. What is the equation for current in terms of power? (Solve for I) VP I = R O A. O BI = O C.I= VPR O D.I=
v=1.000mphv=1.000mph in SI units?
An electric circuit is described by the following equation: d’u du +k+o°u= au, dt di? where t is time in seconds, and w, k, and a are positive constant parameters. a) Assuming that u is the voltage in Volts, find the physical dimensions of the constants k, w, and a in the SI system using the rule of dimension homogeneity. b) Present this equation in the form of the energy balance equation. Find the total instantaneous energy of the circuit E and the dissipative function F.
if v is in meters per second, B in teslas, and L in meters, then the units of the right-hand side of the equation are joules per coulomb or volts (the correct SI units for E ).
Ohm's law for electrical circuits like the one shown in the figure states that V = RI. In this equation, V is a constant voltage, I is the current in amperes, and Ris the resistance in ohms. Your firm has been asked to supply the resistors for a circuit in which V will be 240 volts and I is to be 20±0.2 amp. In what interval does R have to lie for I to be within 0.2 amp of the value I, = 20? R. To what interval must R be held to meet the requirements for the resistance? ohms