In the figure, one end of a uniform beam of weight 220 N is hinged to a wall; the other end is supported by a wire that makes angles 8- 32° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge 8

In the figure, one end of a uniform beam of weight 220 N is hinged to a wall; the other end is supported by a wire that makes angles 8- 32° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge 8

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 38P: A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the...

See similar textbooks

Related questions

Q: A pulley is bolted to a wall as shown. The pulley is a flat disk of mass mp, radius R and moment of…

Q: The Orion Space Capsule has started it's return to earth and is travelling at a speed of 24,600 mph.…

A: Given data, Speed=24600 mph Distance d=270,000 miles

Q: A PARTICLE IS MOVING ALONG A HORIZONTAL LINE ACCORDING TO THE GIVEN EQUATION WHERE AT (t) SECONDS,…

Q: A laser beam with a total power of 22 watts is incident at a normal angle of incidence on a…

Q: What is the magnitude of the electrical force between two uranium nuclei placed a distance of 9.38 x…

A: Given data: Two uranium nuclei Distance (r) = 9.38×10-12 m Required: The magnitude of the electric…

Q: A 23.0-m-long bar of steel expands due to a temperature increase. A 12.0-m-long bar of copper also…

A: Giveninitial length of steel, ls=23 minitial length of copper, lc=12 mgap, x=1.7 cmthermal…

Q: A car starts from rest at a stop sign. It accelerates at 4.0 m/s² for 6.2 s, coasts for 1.8 s, and…

A: initial velocity (u) = 0 m/s a1 = 4 m/s2t1 = 6.2 sec t2 = 1.8sec a3 = - 2.9 m/s2

Q: A smoke sensor can be constructed using light sensors.

A: True

Q: A 0.250 kg lump of clay is dropped from a height of 1.45 m onto the floor. It sticks to the floor…

A: Given: The mass of the clay: m=0.250 kg Hight from where it is dropped: 1.45 m

Q: (a) What focal length must a corrective lens have to enable the eye to see clearly an object 20.7 cm…

Q: A light beam of wavelength 596 hm and intensity 251 W/m^2 shines on a target of area 2.47 m^2 for a…

Q: Light produced by a particular laser has a wavelength of 532 nm. What is its frequency?

A: Given data: A laser beam Wavelength (λ) = 532 nm Required: The frequency (f)

Q: When a car starts suddenly, the front of the car rises to the top, explain this.

A: It is required to explain why the front of the car rises to the top when it starts suddenly.

Q: What is the wavelength in meters of a photon generated by an electron going from n =(8.000x10^0) to…

Q: A leaf of length his positioned d = 69.5 cm in front of a converging lens with a focal length of…

Q: A mass m1 rests on a frictionless horizontal table. Attached to it is a string which runs…

Q: Gravitational Force: Two small objects, with masses m and M, are originally a distance r apart, and…

Q: An astronaut takes what he measures to a be a 10-minute nap in a space station orbiting Earth at…

A: Given time in astronaut frame, t=10 minvelocity of astronaut, v=8000 m/sconcepttime dilation: as per…

Q: A professional golfer is examining a video of a practice swing. The high-speed footage shows that…

Q: The Lost Drone. You and your team are exploring the edge of an Antarctic mountain range and you send…

A: Given that The angle turned after 5 minutes is β=35o east of south The velocity vs time graph The…

Q: When entering the values the answer shows as wrong, would it be that we use 1/12 ML^2 insted of 1/3…

A: Given, Angular velocity = 6 rev/s = 6×2π rad/s = 12π rad/s radius of sphere , r = 3m mass of…

Q: What is the redshift z of a galaxy 186 Mpc away from us? Note: Assume a value of the Hubble…

A: Hubble's law, also known as Hubble- Lemaitre law states that the velocity of the galaxy, also called…

Q: A joelshawon is a subatomic particle with a mass of 3.5 G and it is made out of a joelon (mass 1.5…

Q: of a spherical mirror of radius 36.6 cm, you position an object of height 3.26 cm somewhere along…

Q: A certain obiect weighs 200N in air and 150N when immersed in water. Calculate A)Relative density…

A: Given data: Weight of the object in air (Wair) = 200 N Weight of the object in water (Wwater) =…

Q: Suppose we now turn off the motor and apply a brake to bring the grindstone from its greatest…

A: Given: Moment of inertia of grindstone, I = 2.0 kg-m2 Initial angular speed, ωi = 50 rads Final…

Q: A proton moves through a region containing a uniform electric field given by E= 38.0 ĵ V/m and a…

Q: Work: Find the net work done by friction on a box that moves in a complete circle of radius 1.82 m…

A: Given data The radius is given as r = 1.82 m. The coefficient of kinetic friction is given as…

Q: A gas undergoes a change of state described by the pV diagram shown in the figure below. 4.00- pi10²…

A: Work done is area under PV diagram. from the figure area=12(3-1)×102×(3-1)+2×102×1 =400 J…

Q: focal length of 15.0 cm. A 5.0-cm of 30,0 cm in front of the mirror. HINT: SIMPLY LOCATE WH THE…

A: Given, The focal length is f=15 cm Height of the candle, h=5 cm Object distance, u=30 cm

Q: A 80 g, 37-cm-long rod hangs vertically on a frictionless, horizontal axle passing through its…

A: Given, mass of the rod, M = 80 g length of the rod, l = 37 cm mass of the clay ball, m = 12 g…

Q: The Cavendish experiment marked a milestone in the study of gravity. Part A. What important value…

A: The Cavendish experiment was first attempt that was successful since the time of Newton's to…

Q: Two loudspeakers, A and B (the figure (Figure 1)), are driven by the same amplifier and emit…

Q: A 1.00-cm-high object is placed 3.95 cm to the left of a converging lens of focal length 8.30 cm. A…

A: Note: Distances to the left of lens are taken as negative and distances to the right of lens are…

Q: In 1923, the United States Army (there was no United States Air Force at that time) set a record for…

Q: Gravitational Potential Energy: A stone s held at a height h above the ground. A second stone with…

Q: The curve in the attached figure is alleged to be the wave function for the fifth energy level for a…

A: Here in the above graph the potential is not symmetric, hence the asymmetry in the wave function is…

Q: A large turntable rotates about a fixed vertical axis, making one revolution in 6.00 ss. The moment…

A: Write the given values with the suitable variables. T=6 sI=1300 kg m2m=35 kgr=2.5 m Here, T, I, m,…

Q: An electron in its ground state is trapped in the one-dimensional Coulomb potential energy. What is…

Q: You want the final speed at the bottom of your roller coaster hill to be 25 m/s. What is the height…

A: Given data- The final speed at the bottom of roller coaster is, v=25 m/s let us consider height of…

Q: In order to move the rectangular stones which built the pyramids the ancient Egyptians used a system…

Q: Given that I = 10-12 watts/meter2, what is the intensity of a sound for which the decibel level of…

A: Given data: I0 = 10-12 W/m2 Decibel level (β) = 138 Required: The intensity of the sound (I)

Q: A long steel I-beam used in bridge construction has a length of 19.1 m and is made of an element…

Q: Problem 2: A square loop, length L on each side, is shot with velocity vo into a uniform magnetic…

Q: A 0.250 kg toy car moving with a speed of 0.820 m/s collides with a wall. The figure shows the force…

A: From the concepts of mechanics, we know that the area under a force vs time graph gives us impulse.…

Q: beam shines through air and then strikes a mirror, making an angle theta 45.1 degrees with respect…

A: Given: θ = 45.10 y= 58.7 cm h = 1.78 cm To Find: value of x Diagram:

Q: A 62.00-cm guitar string under a tension of 35.000 N has a mass per unit length of 0.10000 g/cm.…

Q: A satellite of mass m moves in an elliptical orbit around the Earth, see the Figure. The minimum…

A: Required : The correct option

Q: n 2000, a gargantuan iceberg broke away from the Ross Ice Sheet in Antarctica. It was approximately…

Q: what is the gravitational force acting on a person due to another person standing 2 meters away.…

A: Given data: Two persons having same mass Distance (r) = 2 m Mass of each person (m) = 59 kg…

Concept explainers

Rotational Equilibrium And Rotational Dynamics

In physics, the state of balance between the forces and the dynamics of motion is called the equilibrium state. The balance between various forces acting on a system in a rotational motion is called rotational equilibrium or rotational dynamics.

Equilibrium of Forces

The tension created on one body during push or pull is known as force.

Question

PUCHTIDWry
Current Attempt in Progress
In the figure, one end of a uniform beam of weight 220 N is hinged to a wall; the other end is supported by a wire that makes angles 8 =
32° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge
on the beam.
(a) Number i
(b) Number i
(c) Number
CD
Units
Units
Units
Hinge
A
32°C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
In the figure below, a uniform beam of weight 420 N and length 2.8 m is suspended horizontally. On the left it is hinged to a wall; on the right is it supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1200 N. Cable Beam (a) What value of D corresponds to that tension? (b) Give any value for D that won't snap the cable. m
In the figure, a uniform beam of weight 440 N and length 2.3 m is suspended horizontally. On the left it is hinged to a wall; on the right it is supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1100 N. What value of D corresponds to that tension? Cable Вeam Number i Units
A beam with length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board. Suppose the maximum tension that the wire can withstand is 1500 N. What is the maximum load that the hinge can support before the wire breaks?
A beam with a length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board
A 4 m long horizontal uniform beam of mass 24 kg is supported by a wire as shown in the figure. The wire makes an angle of 26 degrees with the beam. Attached to the beam 1.6 m from the wall is a ball with a mass of 57 kg. VWhat is the tension in the string?
Consider the 120-cm board supporting three loads as shown below. The beam weighs 45 grams. If the system is in equilibrium, a. what is the magnitude of the force exerted by the pin support to the board? b. Find the perpendicular distance, x, of the pin support from the left end of the board. 30cm A В C 259 30g 75g
A 1204-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end A 1515-N crate hangs from the far end of the beam. Find the magnitude of the tension in the wire. The angle theta (9) is 29 degrees and the angle phi () is 53 degrees. The length of the beamis L Вeam ROUND OFF FINAL ANSWER TO THE NEAREST WHOLE NUMBER. INPUT THE SYMBOL OF THE UNIT. NO SPACE BETWEEN THE NUMBER AND THE UNIT.
One end of a uniform beam of length L=3mandweight 185 Nis connected to a vertical wall with a cable. The other end is connected to a hinge. The cable makes an angle of 30 degrees with the beam. The cable can withstand a mnaximum tension of 427.0 N. A block of weight 204.0 N is placed on the beam at a distance xWhat is the maximum possible distance xbefore the cable breaks? Acti
In the figure, a uniform beam of weight 400 N and length 3.9 m is suspended horizontally. On the left it is hinged to a wall; on the right it is supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1400 N. What value of D corresponds to that tension? Number MO Units Cable A Beam
Solve Equation (1) for R (in N) and substitute numerical values: R = Finalize The positive value for the angle 0 indicates that our estimate of the direction of R was accurate. Had we selected some other axis for the torque equation, the solution might differ in the details ---Select-- . For example, had we chosen an axis through the center of gravity of the beam, the torque equation would involve both T and R. This equation, coupled with Equations (1) and (2), however, could still be solved for the unknowns. Try it! EXERCISE A person with weight 900 N stands d = 4.00 m away from the wall on a f = 6.00 m beam, as shown in this figure. The weight of the beam is 2,000 N. Define upward as the positive y-direction and to the right as the positive x-direction. 30° d Hint (a) Find the tension (in N) in the wire. (b) Find the horizontal component of the hinge force (in N). (Indicate the direction with the sign of your answer.) (c) Find the vertical component in (N). (Indicate the direction…
One end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an angle of ? = 37.0°above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable.