1.0 k2, hre 100 µ mhos. The load resistance for the transistor is 1 k2 i The h-parameters of a transistor used common emitter circuit are hie x 104, hfe = 50 and hoe the collector circuit. If the transistor is supplied from a signal source of resistance 1000 2, determine (i) input resistance, (ii) output resistance (iii) current gain, and (iv) voltage gain of the amplifier stage. 1.0 %D %3D

1.0 k2, hre 100 µ mhos. The load resistance for the transistor is 1 k2 i The h-parameters of a transistor used common emitter circuit are hie x 104, hfe = 50 and hoe the collector circuit. If the transistor is supplied from a signal source of resistance 1000 2, determine (i) input resistance, (ii) output resistance (iii) current gain, and (iv) voltage gain of the amplifier stage. 1.0 %D %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

power semiconductor device which is used metal in its PN junction. 2. Draw the equivalent circuit model and switching characteristics of the device which is used for low on state loss and high switching frequency operation.
1 The AC input to a common emitter amplifier (Figure 1) is such that it is comparable to thermal voltage VT. For such an amplifier: a. Please show how a hybrid – T small-signal model would look like. Do not ignore early effect. b. Please derive relation for the terminal voltage gain and overall voltage gain. Vcc Rc R RE C Figure 1 You uolont oirouit
Draw, Illustrate and label your schematic diagram before solving the problem. 3) Given an Emitter-Stabilize Biased transistor circuit with beta DC is 250,Base resistor is 150 ohms, collector resistor is 1.5k ohms ,emitter resistor is 500 ohms ,emitter voltage supply is -5v and Voltage at common collector is +28V,Voltage at Base-emitter junction is 0.7v,. Determine Base current, Collector current and Voltage at collector-emitter junction.
2. For the emitter-stabilized bias circuit, determine: a. IBo. b. Ica. c. VCEQ. d. Vc. e. VB. f. VE. 20 V 470 2 ICQ 270 k2 oVc VB B= 125 VCEQ OVE IBQ 2.2 k2
2. Determine the VCB (i.e., voltage difference between collector C and base B) in the transistor circuit shown in the figure below. The transistor is silicon type (i.e., VBE is 0.7V) and has current gain hEE- 150. (Assume the transistor is working on active region) Rc 100 2 RB 10V Vcc 10 k2 VBR = 5V
Qa: A transistor dissipates 50W in an ambient temperature of 60°C, the thermal resistances are 0-0.5 °CW¹, 8ca-4 °CW. Determine the junction temperature without a heat sink. Determine the thermal resistance of the heat sink to avoid the junction temperature exceeding 180°C. )
For the common emitter configuration, the current amplification factor (B) is 90. What will be the value of the current amplification factor (a)? a. 0.5 b. 0.95 c. 0.978 d. 0.989
4 For the transistor shown in below figure, Calculate the value of R, that will just make the transistor work as closed switch. Hence Bpc= 80, VBE = 0.7V, VCE(sat) = 0.2V, Vcc= 12V, Rc= 2.7KN. la) Calculate the In and I.. Vcc RB Rc |b) Calculate Rp- B'
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
VcC R2 RC- RI RL R1 RE VEE Assume: B=100, VA=150, Vcc=12V, VɛE=GND, R=2K, R1=160K, R2=300K, Rɛ=3K, Rc=2.2K, and R1=100K. A.)For the circuit draw the AC equivalent circuit (including the small signal model for the transistor). Then compute r„, ľo, and gm. Then compute Av (the gain for the entire circuit), and Rin (for the whole circuit). B.)Convert the circuit to a common-collector circuit. Draw the new circuit (assume the same values for the input and load resistances). Then compute the terminal voltage gain, and Rin (for the whole circuit), re-computing any parameters that you need to solve.
The DC Current Gain of a Transistor is Select one: a. Ratio of Collector Current to Base Current b. Ratio of Base Current to Collector Current c. Ratio of Emitter Current to Collector Current d. Ratio of Base Current to Emitter Current
Q1:- find the emitter, base and collector currents and VE. (let any parameters if you need). + Vcc=6 V 2 k2 530 k2