Q1// For the BJT amplifier circuit in figure below, determine: 1- Rg, Rc, RE1 and RE2 using Vcc supply of 12 V, an npn silicon transistor with B of 80, of Ic =2 mA and Ve = 7.6 V. Assumed VE = 0.2 Vcc and REI =0.3RĘ. 2- Z , Z, ', Ay, and v, using approximate r, equivalent model. O 12V Rc RB 600 2 10 ka Rs Zo Ra 50 mv -> Zin ww

Q1// For the BJT amplifier circuit in figure below, determine: 1- Rg, Rc, RE1 and RE2 using Vcc supply of 12 V, an npn silicon transistor with B of 80, of Ic =2 mA and Ve = 7.6 V. Assumed VE = 0.2 Vcc and REI =0.3RĘ. 2- Z , Z, ', Ay, and v, using approximate r, equivalent model. O 12V Rc RB 600 2 10 ka Rs Zo Ra 50 mv -> Zin ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Exersice 4: For the Darlington amplifier circuit used in an emitter-follower configuration appears in figure below: . Determine the dc levels of Vi, Ve, Vi, Ves, and Ver. . Find the currents I, Iz, and Irz. . Calculate Zi and Zo. . Determine the voltage gain Ay = Vo/Vi and current gain Ai=IL/l;. . Repeat parts 1 to 4 with a load resistor of 1.2 kQ. . Evaluate A = Vo/Vs if the source has an internal resistance of 1.2 kQ and the applied load is 10 kQ. omAwWNE 416V L i prammm, I Tour i,
1.The voltage measured from the collector to the emitter is the sum of the voltage base-emitter plus the voltage collector-base. Select one: True Or False 2.A decrease in base current of a C-E amplifier causes the voltage measured between the emitter and the collector to increase. Select one: True Or False 3.A FET is ..............controlled device whereas a bipolar transistor is a.............controlled device. Answer:
Given the MOSFET in Figure 6 has bran) = 200 mA at VGs = 4 V and V(Tn) = 2 V; i. Plot the transfer characteristic curve for the MOSFET. b) i. Determine the operating point Vasa, Ioa and Vosa for the circuit. ii. Calculate the value of the transconductance gm at the Q-point. iv. Determine the voltage gain and input impedance of the amplifier. 15 V 1 kn. Coe 1.5 M2. Cin 33 kn. Vn 30 ka Figure 6
2. The circuit in Figure 2 has a BJT transistor with B= 200, VA = 20 V. Determine BJT DC collector current and DC collector voltage. Determine the small-signal input resistance seen by the AC voltage source, the output resistance at Vout, and the transfer function Vout/Vin. HH 1.7 V 100k Figure 2, Problem 2 10 V 2k Vout 2k
Given a D-MOSFET circuit used as an amplifier with the following parameter: IDSS=12mA and a transconductance of gm=3.2 mS. Determine the DC drain to source voltage VDS and the AC output voltage if Vin=500 mV.
Draw, Illustrate and label your schematic diagram before solving the problem. 3) Given an Emitter-Stabilize Biased transistor circuit with beta DC is 250,Base resistor is 150 ohms, collector resistor is 1.5k ohms ,emitter resistor is 500 ohms ,emitter voltage supply is -5v and Voltage at common collector is +28V,Voltage at Base-emitter junction is 0.7v,. Determine Base current, Collector current and Voltage at collector-emitter junction.
2. The parameters of the transistor as shown in the figure below are ß = 100 and VA = 100V. a. Find the dc voltages at the base and emitter terminals. b. Find Rc such that VCEQ = 3.5V. c. Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = Vo/Vs. d. Repeat part (c) if a 5000 source resistor is in series with the vs signal source. V+ = +5 V Rs = 100 £2 www Us Cc RB = 10 ΚΩ I= Iausmi 0.35 mA www RC -000 V=-5 V CE
For the circuit given below, transistor parameters are given as -= 0.1mA/V², Vth,p=-1V, A=0. Using these information, a) Design the circuit (find the values of R1and R2) such that Ip=100HA. b) Find the small signal voltage gain Vo/Vi of the circuit. R1 10 V - R2 ww0-2.5 V
The amplifier in the circuit below is driven by a signal generator v, with a small sine wave signal vhose average value is zero. Assume the transistor has a value of B-100, and V-26 mV. a. You need to design the circuit so that the de emitter current IE of the emitter resistor RE to establish the desired de emitter current. = 1 mA. Specify the value b. A de collector voltage of +5 volts is desired. Specify the value of the collector resistor Re to establish the desired de collector voltage. For this part assume that RL 5 K and the Early Effect needs to be considered. The transistor has a VA 100 Volts. Draw the ac small signal equivalent circuit model of the amplifier and determine its voltage gain. 91SV C. 2.5k MM do RE -15 V 84 Vout RL
Common Gate MOSFET Amplifier has Select one: a. input is connected to the Gate and the output is taken from the Source b. input is connected to the Source and the output is taken from the Drain c. input is connected to the Gate and the output is taken from the Drain d. input is connected to the Source and the output is taken from the Gate 55 week 10 material Jump to... CE255/EE255 (01)- 16
2.1) Design a BJT common-emitter amplifier (use the figure A or B in former page!) with a gain of 9. The Q point parameters should be IC = 3 mA and VCE = ŠV. A power supply of 20 V is available. Manufacturers' spec sheets give: min = 100, ht. = 200.Take VBE = 0.7 V. 2.2) Analyze the BJT circuit given in figure – 1. Determine the collector currents for DC current gains Boc = 100 and BDc = 200. Calculate the Q point of both cases. Detemine the percentage change in Ic (collector current), Vcz (collector-emitter current). Use the below formulas: I -I V -V CE -100) 100 d-200) -100) 100 : % Ic CE( -200) % Ic I (-100) Calculate the DC Load line of circuit. CE( -100) Voc-10" R2=1k2 R1=300k 10V Figure – 1
Vsis (~ Q3 (a) What is the advantage of using MOSFET as compared to BJT at the first stage of multi-stage amplifier? Rais 600 02 www Z₁ (b) Describe the function of the capacitor for the following condition: (1) (ii) SEEE/SKEE 1073 (c) The transistors parameters in Figure Q.3 are given as follow: BJT (iv) ↑ B-350, VBE 0.7 V, Ic=0.3 mA, VT 26 mV, and ro=00 E-MOSFETk 0.8 mA/V², VT- Vas(T) = 1 V C₁ HE a capacitor between stage 1 and stage 2 of a RC-coupled amplifier. bypass capacitor which is commonly used in small signal amplifier. (i) Draw the ac equivalent circuit at middle frequency for circuit in Figure Q.3 by using hybrid-x model. (ii) Determine the values of Z., Ziz and Zo. (iii) Calculate the gain, v/v, in decibel (dB). Draw and label the waveforms vo when v=2 sin 50t [mV] for one complete cycle. + Roi 50 ΚΩ Vi Ra 6 kn Ro 4.5 k Q₁ Rs 3 kQ C₂ не +15 V DS ↑ 22 R₁ 75 k R₂ 9 kn Figure Q.3 Multistage amplifier circuit Re RE 2kQ Rez 1kQ ← 2₂ -C₁ R₂ 20k2 %