Vector Mechanics for Engineers: Statics and Dynamics
Vector Mechanics for Engineers: Statics and Dynamics
12th Edition
ISBN: 9781259638091
Author: Ferdinand P. Beer, E. Russell Johnston Jr., David Mazurek, Phillip J. Cornwell, Brian Self
Publisher: McGraw-Hill Education
bartleby

Concept explainers

bartleby

Videos

Question
Book Icon
Chapter 9.6, Problem 9.179P

(a)

To determine

Find the principal moment of inertia at the origin O.

(a)

Expert Solution
Check Mark

Answer to Problem 9.179P

The principal moment of inertia at the origin O is K1=0.363ma2,K2=1.583ma2,and K3=1.72ma2_.

Explanation of Solution

Given information:

The mass of the cylinder is denoted by m.

The length of the circular cylinder is denoted by a.

The diameter OB of the top surface makes 45° with x and z axis.

Calculation:

Show the homogeneous circular cylinder as shown in Figure 1.

Vector Mechanics for Engineers: Statics and Dynamics, Chapter 9.6, Problem 9.179P , additional homework tip  1

Refer Figure 1.

Refer Figure 9.28.

Apply parallel axis theorem

Show the moment of inertia of the circular cylinder about the y axis as follows:

Iy=12ma2+ma2=32ma2

Show the moment of inertia of the circular cylinder about the x and z axis as follows:

Ix=Iz=112m(3a2+L2)+m[(a2)2+(a2)2]} (1)

Here, a is the radius of the cylinder and L is the length of the cylinder.

Substitute a for L in Equation (1).

Ix=Iz=112m(3a2+a2)+m[(a2)2+(a2)2]=13ma2+m[a22+a24]=13ma2+34ma2=1312ma2

The centroidal axis products of inertia are zero due to symmetry.

Ixy=Iyz=Izx=0

Write the centroidal locations as measured from the origin O along the x, y and z axis as below;

x¯=(a2), y¯=(a2) and z¯=(a2).

Express the moment of inertia Ixy as follows:

Ixy=Ixy+mx¯y¯=0+m(a2)(a2)=122ma2

Express the moment of inertia Iyz as follows:

Iyz=Iyz+my¯z¯=0+m(a2)(a2)=122ma2

Express the moment of inertia Izx as follows:

Izx=Izx+mz¯x¯=0+m(a2)(a2)=12ma2

Show the Equation 9.56 as follows:

{K3(Ix+Iy+Iz)K2+(IxIy+IyIz+IzIxIxy2Iyz2Izx2)K(IxIyIzIxIyz2IyIzx2IzIxy22IxyIyzIzx)}=0

Substitute 1312ma2 for Ix, 32ma2 for Iy, 1312ma2 for Iz, 122ma2 for Ixy, 122ma2 for Iyz, and 12ma2 for Izx.

{K3(1312ma2+32ma2+1312ma2)K2+[(1312ma2)(32ma2)+(32ma2)(1312ma2)+(1312ma2)(1312ma2)(122ma2)2(122ma2)2(12ma2)2]K[(1312ma2)(32ma2)(1312ma2)(1312ma2)(122ma2)2(32ma2)(12ma2)2(1312ma2)(122ma2)22(122ma2)(122ma2)(12ma2)]}=0{K3(1312+32+1312)K2ma2+[(1312)(32)+(32)(1312)+(1312)(1312)(122)2(122)2(12)2]K(ma2)2[(32)(1312)(1312)(1312)(122)2(32)(12)2(1312)(122)22(122)(122)(12)](ma2)3}=0

Substitute ma2ζ for K.

ζ3113ζ2+565144ζ9596=0

Solve the above Equation and get the values of ζ1, ζ2, and ζ3 as follows:

ζ1=0.363ζ2=1.583ζ3=1.72

Show the principal moment of inertia as follows:

K1=0.363ma2K2=1.583ma2K3=1.72ma2

Thus, the principal mass moment of inertia are K1=0.363ma2,K2=1.583ma2,and K3=1.72ma2_

(b)

To determine

Find the angles made by the principal axis of inertia at O with the coordinate axis.

(b)

Expert Solution
Check Mark

Answer to Problem 9.179P

The angles made by the principal axis of inertia at O with the coordinate axis is (θx)1=49.7°,(θy)1=113.7°,(θz)1=49.7°_,(θx)2=45°,(θy)2=90°,(θz)2=135°_,(θx)3=73.5°,(θy)3=23.7°,(θz)3=73.5°_.

Explanation of Solution

Given information:

Consider the direction cosines of each principal axis are denoted by λx,λy,λz.

Calculation:

Refer Part (a).

Show the Equation 9.54 as follows:

(IxK)λxIxyλyIzxλz=0IzxλxIyzλy+(IzK)λz=0} (2)

Substitute 1312ma2 for Ix, 1312ma2 for Iz, 122ma2 for Ixy, 122ma2 for Iyz, and 12ma2 for Izx.

(1312ma2K)λx(122)ma2λy(12ma2)λz=0(12ma2)λx(122)ma2λy+(1312ma2K)λz=0} (3)

Modify Equation (3).

Consider K=ma2ζ. Then,

(1312ζ)λx(122)λy(12)λz=0(12)λx(122)λy+(1312ζ)λz=0} (4)

Solve Equation (4).

1312ζ=12ζ=1912

Add both the Equation in Equation (4).

[1312ζ(12)]λx+[12(1312ζ)]λz=0λx=λz

Substitute λx for λz in Equation (4).

(1312ζ)λx(122)λy(12)λx=0(122)λy=(121312+ζ)λx(122)λy=(ζ712)λxλy=22(ζ712)λx

Show the Equation 9.57 as follows:

λx2+λy2+λz2=1

Substitute 22(ζ712)λx for λy, and λx for λz.

λx2+[22(ζ712)λx]2+λx2=1λx2+8(ζ712)2λx2+λx2=1[2+8(ζ712)2]λx2=1 (5)

Consider K1.

Substitute 0.363 for ζ1 in Equation (5).

[2+8(0.363712)2](λx)12=1(λx)1=(λz)1=0.647249

Calculate the value of (λy)1 as follows:

(122)(λy)1=(ζ1712)(λx)1

Substitute 0.647249 for (λx)1 and 0.363 for ζ1.

(122)(λy)1=(0.363712)×0.647249(λy)1=0.402662

Show the direction cosines (θx)1,(θy)1,(θz)1 using the relation:

cos(θx)1=(λx)1=0.647249(θx)1=cos1(0.647249)=49.7°

cos(θz)1=(λz)1=0.647249(θz)1=cos1(0.647249)=49.7°

cos(θy)1=(λy)1=0.402662(θy)1=cos1(0.402662)=113.7°

Conisder K3.

Substitute 1.720 for ζ3 in Equation (5).

[2+8(1.720712)2](λx)32=1(λx)3=(λz)3=0.284726

Calculate the value of (λy)3 as follows:

(122)(λy)3=(ζ3712)(λx)3

Substitute 0.284726 for (λx)3 and 1.720 for ζ3.

(122)(λy)3=(1.720712)×0.647249(λy)3=0.915348

Show the direction cosines (θx)3,(θy)3,(θz)3 using the relation:

cos(θx)3=(λx)3=0.284726(θx)3=cos1(0.284726)=73.5°

cos(θz)3=(λz)3=0.284726(θz)3=cos1(0.284726)=73.5°

cos(θy)3=(λy)3=0.915348(θy)3=cos1(0.915348)=23.7°

Consider K2.

Show the Equation 9.54b as follows:

Ixyλx+(IyK)λyIyzλz=0

Substitute 32ma2 for Iy, 122ma2 for Ixy, and 122ma2 for Iyz.

(122ma2)λx+(32ma2K)λy+(122ma2)λz=0122λx+(32ζ)λy+(122)λz=0 (6)

Refer Equation (3) and (6).

(1312ζ)λx(122)λy(12)λz=0122λx+(32ζ)λy+(122)λz=0} (7)

Substitute 1912 for ζ in Equation (4).

(13121912)(λx)2(122)(λy)2(12)(λz)2=0122(λx)2+(321912)(λy)2+(122)(λz)2=0

Modify above Equations as follows:

112(λx)2+(122)(λy)2(12)(λz)2=0122(λx)2112(λy)2+(122)(λz)2=0} (8)

Solve Equation (8) and get the value of (λy)2=0.

Show the Equation 9.57 as follows:

(λx)22+(λy)22+(λz)22=1(λx)22+0+(λz)22=1(λx)22+(λz)22=1

Substitute λx for λz.

(λx)22+(λx)22=1(λx)2=12

(λz)2=12

Show the direction cosines (θx)2,(θy)2,(θz)2 using the relation:

cos(θx)2=(λx)2=12(θx)2=cos1(12)=45°

cos(θz)2=(λz)2=(12)(θz)2=cos1(12)=135°

cos(θy)2=(λy)2=0(θy)2=cos1(0)=90°

Thus, the velocity of the point B is 1.537ft/s(Acting 77.48°Clockwise above the horizontal)_.

(c)

To determine

Sketch the body and show the orientation of the principal axis of inertia relative to x, y, and z axis.

(c)

Expert Solution
Check Mark

Explanation of Solution

Given information:

Calculation:

Refer Part (a) and (b).

Sketch the body and show the orientation of the principal axis of inertia relative to x, y, and z axis as shown in Figure 2.

Vector Mechanics for Engineers: Statics and Dynamics, Chapter 9.6, Problem 9.179P , additional homework tip  2

Refer Figure 2.

The principal axis 1 and 3 lies on the vertical plane of symmetry passing through OB.

The principal axis 2 lies in xz plane.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Consider Figure Q3, Determine the mass moment of inertia of the composite body about the x and y axes.  Mass of rod = 2 kg/m Mass of disc = 15 kg/m2
A homogeneous wire with a mass per unit length of 0.056 kg/m is used to form the figure shown. Determine the mass moment of inertia of the wire with respect to each of the coordinate axes.
2. Determine the mass moment of inertia for the following rigid bodies about an axis at its center orthogonal to the page.

Chapter 9 Solutions

Vector Mechanics for Engineers: Statics and Dynamics

Ch. 9.1 - Prob. 9.11PCh. 9.1 - Prob. 9.12PCh. 9.1 - 9.12 through 9.14 Determine by direct integration...Ch. 9.1 - 9.12 through 9.14 Determine by direct integration...Ch. 9.1 - Prob. 9.15PCh. 9.1 - Prob. 9.16PCh. 9.1 - Prob. 9.17PCh. 9.1 - Prob. 9.18PCh. 9.1 - Determine the moment of inertia and the radius of...Ch. 9.1 - Prob. 9.20PCh. 9.1 - Determine the polar moment of inertia and the...Ch. 9.1 - Prob. 9.22PCh. 9.1 - Prob. 9.23PCh. 9.1 - 9.23 and 9.24 Determine the polar moment of...Ch. 9.1 - Prob. 9.25PCh. 9.1 - Prob. 9.26PCh. 9.1 - Prob. 9.27PCh. 9.1 - Prob. 9.28PCh. 9.1 - Prob. 9.29PCh. 9.1 - Prove that the centroidal polar moment of inertia...Ch. 9.2 - 9.31 and 9.32 Determine the moment of inertia and...Ch. 9.2 - 9.31 and 9.32 Determine the moment of inertia and...Ch. 9.2 - 9.33 and 9.34 Determine the moment of inertia and...Ch. 9.2 - 9.33 and 9.34 Determine the moment of inertia and...Ch. 9.2 - Determine the moments of inertia of the shaded...Ch. 9.2 - Determine the moments of inertia of the shaded...Ch. 9.2 - Prob. 9.37PCh. 9.2 - Prob. 9.38PCh. 9.2 - Prob. 9.39PCh. 9.2 - Prob. 9.40PCh. 9.2 - 9.41 through 9.44 Determine the moments of inertia...Ch. 9.2 - 9.41 through 9.44 Determine the moments of inertia...Ch. 9.2 - Prob. 9.43PCh. 9.2 - Prob. 9.44PCh. 9.2 - 9.45 and 9.46 Determine the polar moment of...Ch. 9.2 - Prob. 9.46PCh. 9.2 - 9.47 and 9.48 Determine the polar moment of...Ch. 9.2 - 9.47 and 9.48 Determine the polar moment of...Ch. 9.2 - To form a reinforced box section, two rolled W...Ch. 9.2 - Two channels are welded to a d 12-in. steel plate...Ch. 9.2 - Prob. 9.51PCh. 9.2 - Two 20-mm steel plates are welded to a rolled S...Ch. 9.2 - A channel and a plate are welded together as shown...Ch. 9.2 - Prob. 9.54PCh. 9.2 - Two L76 76 6.4-mm angles are welded to a C250 ...Ch. 9.2 - Prob. 9.56PCh. 9.2 - Prob. 9.57PCh. 9.2 - 9.57 and 9.58 The panel shown forms the end of a...Ch. 9.2 - Prob. 9.59PCh. 9.2 - Prob. 9.60PCh. 9.2 - Prob. 9.61PCh. 9.2 - Prob. 9.62PCh. 9.2 - Prob. 9.63PCh. 9.2 - Prob. 9.64PCh. 9.2 - Prob. 9.65PCh. 9.2 - Prob. 9.66PCh. 9.3 - 9.67 through 9.70 Determine by direct integration...Ch. 9.3 - 9.67 through 9.70 Determine by direct integration...Ch. 9.3 - 9.67 through 9.70 Determine by direct integration...Ch. 9.3 - Prob. 9.70PCh. 9.3 - Prob. 9.71PCh. 9.3 - Prob. 9.72PCh. 9.3 - Prob. 9.73PCh. 9.3 - 9.71 through 9.74 Using the parallel-axis theorem,...Ch. 9.3 - Prob. 9.75PCh. 9.3 - 9.75 through 9.78 Using the parallel-axis theorem,...Ch. 9.3 - Prob. 9.77PCh. 9.3 - Prob. 9.78PCh. 9.3 - Determine for the quarter ellipse of Prob. 9.67...Ch. 9.3 - Determine the moments of inertia and the product...Ch. 9.3 - Determine the moments of inertia and the product...Ch. 9.3 - 9.75 through 9.78 Using the parallel-axis theorem,...Ch. 9.3 - Determine the moments of inertia and the product...Ch. 9.3 - Determine the moments of inertia and the product...Ch. 9.3 - Prob. 9.85PCh. 9.3 - 9.86 through 9.88 For the area indicated,...Ch. 9.3 - Prob. 9.87PCh. 9.3 - Prob. 9.88PCh. 9.3 - Prob. 9.89PCh. 9.3 - 9.89 and 9.90 For the angle cross section...Ch. 9.4 - Using Mohrs circle, determine for the quarter...Ch. 9.4 - Using Mohrs circle, determine the moments of...Ch. 9.4 - Prob. 9.93PCh. 9.4 - Using Mohrs circle, determine the moments of...Ch. 9.4 - Using Mohrs circle, determine the moments of...Ch. 9.4 - Using Mohrs circle, determine the moments of...Ch. 9.4 - For the quarter ellipse of Prob. 9.67, use Mohrs...Ch. 9.4 - 9.98 though 9.102 Using Mohrs circle, determine...Ch. 9.4 - Prob. 9.99PCh. 9.4 - 9.98 though 9.102 Using Mohrs circle, determine...Ch. 9.4 - Prob. 9.101PCh. 9.4 - Prob. 9.102PCh. 9.4 - Prob. 9.103PCh. 9.4 - 9.104 and 9.105 Using Mohrs circle, determine the...Ch. 9.4 - 9.104 and 9.105 Using Mohrs circle, determine the...Ch. 9.4 - For a given area, the moments of inertia with...Ch. 9.4 - it is known that for a given area Iy = 48 106 mm4...Ch. 9.4 - Prob. 9.108PCh. 9.4 - Prob. 9.109PCh. 9.4 - Prob. 9.110PCh. 9.5 - A thin plate with a mass m is cut in the shape of...Ch. 9.5 - A ring with a mass m is cut from a thin uniform...Ch. 9.5 - A thin elliptical plate has a mass m. Determine...Ch. 9.5 - The parabolic spandrel shown was cut from a thin,...Ch. 9.5 - Prob. 9.115PCh. 9.5 - Fig. P9.115 and P9.116 9.116 A piece of thin,...Ch. 9.5 - A thin plate of mass m is cut in the shape of an...Ch. 9.5 - Fig. P9.117 and P9.118 9.118 A thin plate of mass...Ch. 9.5 - Determine by direct integration the mass moment of...Ch. 9.5 - The area shown is revolved about the x axis to...Ch. 9.5 - The area shown is revolved about the x axis to...Ch. 9.5 - Determine by direct integration the mass moment of...Ch. 9.5 - Fig. P9.122 and P9.123 9.123 Determine by direct...Ch. 9.5 - Prob. 9.124PCh. 9.5 - Prob. 9.125PCh. 9.5 - Prob. 9.126PCh. 9.5 - Prob. 9.127PCh. 9.5 - Prob. 9.128PCh. 9.5 - Prob. 9.129PCh. 9.5 - Knowing that the thin cylindrical shell shown has...Ch. 9.5 - A circular hole of radius r is to be drilled...Ch. 9.5 - The cups and the arms of an anemometer are...Ch. 9.5 - Prob. 9.133PCh. 9.5 - Determine the mass moment of inertia of the 0.9-lb...Ch. 9.5 - Prob. 9.135PCh. 9.5 - Prob. 9.136PCh. 9.5 - A 2-mm thick piece of sheet steel is cut and bent...Ch. 9.5 - A section of sheet steel 0.03 in. thick is cut and...Ch. 9.5 - A corner reflector for tracking by radar has two...Ch. 9.5 - A farmer constructs a trough by welding a...Ch. 9.5 - The machine element shown is fabricated from...Ch. 9.5 - Determine the mass moments of inertia and the...Ch. 9.5 - Determine the mass moment of inertia of the steel...Ch. 9.5 - Prob. 9.144PCh. 9.5 - Determine the mass moment of inertia of the steel...Ch. 9.5 - Aluminum wire with a weight per unit length of...Ch. 9.5 - The figure shown is formed of 18-in.-diameter...Ch. 9.5 - A homogeneous wire with a mass per unit length of...Ch. 9.6 - Determine the mass products of inertia Ixy, Iyz,...Ch. 9.6 - Determine the mass products of inertia Ixy, Iyz,...Ch. 9.6 - Determine the mass products of inertia Ixy, Iyz,...Ch. 9.6 - Determine the mass products of inertia Ixy, Iyz,...Ch. 9.6 - 9.153 through 9.156 A section of sheet steel 2 mm...Ch. 9.6 - Prob. 9.154PCh. 9.6 - Prob. 9.155PCh. 9.6 - 9.153 through 9.156 A section of sheet steel 2 mm...Ch. 9.6 - Prob. 9.157PCh. 9.6 - Prob. 9.158PCh. 9.6 - Prob. 9.159PCh. 9.6 - Prob. 9.160PCh. 9.6 - Prob. 9.161PCh. 9.6 - For the homogeneous tetrahedron of mass m shown,...Ch. 9.6 - Prob. 9.163PCh. 9.6 - Prob. 9.164PCh. 9.6 - Prob. 9.165PCh. 9.6 - Determine the mass moment of inertia of the steel...Ch. 9.6 - Prob. 9.167PCh. 9.6 - Prob. 9.168PCh. 9.6 - Prob. 9.169PCh. 9.6 - 9.170 through 9.172 For the wire figure of the...Ch. 9.6 - Prob. 9.171PCh. 9.6 - Prob. 9.172PCh. 9.6 - Prob. 9.173PCh. 9.6 - Prob. 9.174PCh. 9.6 - Prob. 9.175PCh. 9.6 - Prob. 9.176PCh. 9.6 - Prob. 9.177PCh. 9.6 - Prob. 9.178PCh. 9.6 - Prob. 9.179PCh. 9.6 - Prob. 9.180PCh. 9.6 - Prob. 9.181PCh. 9.6 - Prob. 9.182PCh. 9.6 - Prob. 9.183PCh. 9.6 - Prob. 9.184PCh. 9 - Determine by direct integration the moments of...Ch. 9 - Determine the moment of inertia and the radius of...Ch. 9 - Prob. 9.187RPCh. 9 - Prob. 9.188RPCh. 9 - Prob. 9.189RPCh. 9 - Two L4 4 12-in. angles are welded to a steel...Ch. 9 - Prob. 9.191RPCh. 9 - Prob. 9.192RPCh. 9 - Prob. 9.193RPCh. 9 - Prob. 9.194RPCh. 9 - Prob. 9.195RPCh. 9 - Determine the mass moment of inertia of the steel...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
Recommended textbooks for you
Text book image
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
moment of inertia; Author: NCERT OFFICIAL;https://www.youtube.com/watch?v=A4KhJYrt4-s;License: Standard YouTube License, CC-BY