Vector Mechanics for Engineers: Statics and Dynamics
Vector Mechanics for Engineers: Statics and Dynamics
12th Edition
ISBN: 9781259638091
Author: Ferdinand P. Beer, E. Russell Johnston Jr., David Mazurek, Phillip J. Cornwell, Brian Self
Publisher: McGraw-Hill Education
bartleby

Videos

Question
Book Icon
Chapter 8.4, Problem 8.119P

(a)

To determine

Find the smallest combined mass m of the bucket for the block C will remain at rest.

(a)

Expert Solution
Check Mark

Answer to Problem 8.119P

The smallest combined mass m of the bucket is 9.46kg_.

Explanation of Solution

Given information:

The mass of the block C is mC=100kg.

The coefficient of static friction is μs=0.35.

The coefficient of kinetic friction is μk=0.25.

The drum B is frozen and cannot rotate.

Calculation:

Show the free-body diagram of the drum B as in Figure 1.

Vector Mechanics for Engineers: Statics and Dynamics, Chapter 8.4, Problem 8.119P , additional homework tip  1

Find the angle of the belt wounded around the drum as follows;

β=120°×π180°=2π3rad

Find the tension T2 in terms of tension T1 using the equation.

T2T1=eμβ

Substitute mg for T1.

T2mg=eμβT2=mgeμβ (1)

Here, the acceleration due to gravity is g.

Consider the value of acceleration due to gravity is g=9.81m/s2.

Show the free-body diagram of the block C as in Figure 2.

Vector Mechanics for Engineers: Statics and Dynamics, Chapter 8.4, Problem 8.119P , additional homework tip  2

At rest, the cable slips on the drum. The motion impending is along the x-axis. ().

μ=μs

Substitute 9.81m/s2 for g, 0.23 for μ and 2π3 for β in Equation (1).

T2=m×9.81×e0.35×2π3=20.41848m

Resolve the horizontal component of forces.

+Fx=0NmCgcos30°=0

Substitute 100 kg for mC and 9.81m/s2 for g.

N100×9.81×cos30°=0N=849.571N

Find the friction force (F) using the relation.

F=μsN

Substitute 0.35 for μs and 849.571 N for N.

F=0.35×849.571=297.35N

Resolve the vertical component of forces.

+Fy=0T2+FmCgsin30°=0

Substitute 20.41848m for T2, 297.35 N for F, and 100 kg for mC, and 9.81m/s2 for g.

20.41848m+297.35100×9.81×sin30°=020.41848m+297.35490.5=0m=9.46kg

Therefore, the smallest combined mass m of the bucket is 9.46kg_.

(b)

To determine

Find the smallest combined mass m of the bucket for the block C start moving up the incline.

(b)

Expert Solution
Check Mark

Answer to Problem 8.119P

The smallest combined mass m of the bucket is 167.2kg_.

Explanation of Solution

Given information:

The mass of the block C is mC=100kg.

The coefficient of static friction is μs=0.35.

The coefficient of kinetic friction is μk=0.25.

The drum B is frozen and cannot rotate.

Calculation:

Show the free-body diagram of the drum B as in Figure 3.

Vector Mechanics for Engineers: Statics and Dynamics, Chapter 8.4, Problem 8.119P , additional homework tip  3

Find the angle of the belt wounded around the drum as follows;

β=120°×π180°=2π3rad

Find the tension T2 in terms of tension T1 using the equation.

T2T1=eμβ

Substitute mg for T2.

mgT1=eμβT1=mgeμβ (2)

Show the free-body diagram of the block C as in Figure 4.

Vector Mechanics for Engineers: Statics and Dynamics, Chapter 8.4, Problem 8.119P , additional homework tip  4

When the block start moving up the incline; μ=μs.

No slipping occurs at block and drum. The motion impending is against the x-axis. ().

Substitute 9.81m/s2 for g, 0.35 for μ and 2π3 for β in Equation (2).

T1=m×9.81e0.35×2π3=4.71319m

Resolve the horizontal component of forces.

+Fx=0NmCgcos30°=0

Substitute 100 kg for mC and 9.81m/s2 for g.

N100×9.81×cos30°=0N=849.571N

Find the friction force (F) using the relation.

F=μsN

Substitute 0.35 for μs and 849.571 N for N.

F=0.35×849.571=297.35N

Resolve the vertical component of forces.

+Fy=0T1FmCgsin30°=0

Substitute 4.71319m for T1, 297.35 N for F, and 100 kg for mC, and 9.81m/s2 for g.

4.71319m297.35100×9.81×sin30°=04.71319m297.35490.5=0m=167.2kg

Therefore, the smallest combined mass m of the bucket is 167.2kg_.

(c)

To determine

Find the smallest combined mass m of the bucket for the block C continue moving up the incline at constant speed.

(c)

Expert Solution
Check Mark

Answer to Problem 8.119P

The smallest combined mass m of the bucket is 121kg_.

Explanation of Solution

Given information:

The mass of the block C is mC=100kg.

The coefficient of static friction is μs=0.35.

The coefficient of kinetic friction is μk=0.25.

The drum B is frozen and cannot rotate.

Calculation:

Show the free-body diagram of the drum B as in Figure 5.

Vector Mechanics for Engineers: Statics and Dynamics, Chapter 8.4, Problem 8.119P , additional homework tip  5

Find the angle of the belt wounded around the drum as follows;

β=120°×π180°=2π3rad

Find the tension T2 in terms of tension T1 using the equation.

T2T1=eμβ

Substitute mg for T2.

mgT1=eμβT1=mgeμβ (3)

Show the free-body diagram of the block C as in Figure 6.

Vector Mechanics for Engineers: Statics and Dynamics, Chapter 8.4, Problem 8.119P , additional homework tip  6

When the block start moving up the incline; μ=μk.

No slipping occurs at block and drum. The motion impending is against the x-axis. ().

Substitute 9.81m/s2 for g, 0.25 for μ and 2π3 for β in Equation (3).

T1=m×9.81e0.25×2π3=5.81130m

Resolve the horizontal component of forces.

+Fx=0NmCgcos30°=0

Substitute 100 kg for mC and 9.81m/s2 for g.

N100×9.81×cos30°=0N=849.571N

Find the friction force (F) using the relation.

F=μkN

Substitute 0.25 for μs and 849.571 N for N.

F=0.25×849.571=212.39275N

Resolve the vertical component of forces.

+Fy=0T1FmCgsin30°=0

Substitute 5.81130m for T1, 212.39275 N for F, and 100 kg for mC, and 9.81m/s2 for g.

5.81130m212.39275100×9.81×sin30°=05.81130m212.39275490.5=0m=121kg

Therefore, the smallest combined mass m of the bucket is 121kg_.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Solve Prob. 8.93 assuming that the normal force per unit area between the disk and the floor varies linearly from a maximum at the center to zero at the circumference of the disk.(Reference to Problem 8.93):A 50-lb electric floor polisher is operated on a surface for which the coefficient of kinetic friction is 0.25. Assuming that the normal force per unit area between the disk and the floor is uniformly distributed, determine the magnitude Q of the horizontal forces required to prevent motion of the machine.
As shown, a man is leaning against the side of a cabinet with an unusual design. The cabinet's main body weighs 25 kg, while the upper rectangular portion weighs 3 kg. Assume the coefficients of friction between the cabinet and the floor are  μs = 0.33 and μk = 0.28. Knowing that the force P exerted by the man's shoulder on the horizontal cabinet: 2. Determine which of the following is the CORRECT equilibrium equation obtained from the system's force diagram.  A. ΣF = 0: N - 245.25 = 0B. ΣF = 0: P - μ N = 0C. ΣM = 0: 245.25(0.55) + 29.43(0.2) - N(x) - P(1.5) = 0
A belt of negligible mass passes between cylinders A and B and is pulled to the right with a force P. Cylinders A and B weigh, respectively, 5 and 20 lb. The shaft of cylinder A is free to slide in a vertical slot and the coefficients of friction between the belt and each of the cylinders are µs = 0.50 and µk = 0.40. For P = 3.6 lb, determine (a) whether slipping occurs between the belt and either cylinder, (b) the angular acceleration of each cylinder.

Chapter 8 Solutions

Vector Mechanics for Engineers: Statics and Dynamics

Ch. 8.1 - The 10-kg block is attached to link AB and rests...Ch. 8.1 - Considering only values of less than 90,...Ch. 8.1 - Prob. 8.9PCh. 8.1 - Prob. 8.10PCh. 8.1 - The 50-lb block A and the 25-lb block B are...Ch. 8.1 - The 50-lb block A and the 25-lb block B are...Ch. 8.1 - Three 4-kg packages A, B, and C are placed on a...Ch. 8.1 - Prob. 8.14PCh. 8.1 - A uniform crate with a mass of 30 kg must be moved...Ch. 8.1 - A worker slowly moves a 50-kg crate to the left...Ch. 8.1 - Prob. 8.17PCh. 8.1 - A 200-lb sliding door is mounted on a horizontal...Ch. 8.1 - Prob. 8.19PCh. 8.1 - Prob. 8.20PCh. 8.1 - Prob. 8.21PCh. 8.1 - Prob. 8.22PCh. 8.1 - The 10-lb uniform rod AB is held in the position...Ch. 8.1 - Prob. 8.24PCh. 8.1 - Prob. 8.25PCh. 8.1 - Prob. 8.26PCh. 8.1 - The press shown is used to emboss a small seal at...Ch. 8.1 - The machine base shown has a mass of 75 kg and is...Ch. 8.1 - Prob. 8.29PCh. 8.1 - Prob. 8.30PCh. 8.1 - Prob. 8.31PCh. 8.1 - Prob. 8.32PCh. 8.1 - Prob. 8.33PCh. 8.1 - A driver starts the engine of an automobile that...Ch. 8.1 - Prob. 8.35PCh. 8.1 - Two uniform rods each of weight W and length L are...Ch. 8.1 - A 1.2-m plank with a mass of 3 kg rests on two...Ch. 8.1 - Two identical uniform boards, each with a weight...Ch. 8.1 - A uniform 20-kg tube resting on a loading dock...Ch. 8.1 - Prob. 8.40PCh. 8.1 - A 10-ft beam, weighing 1200 lb, is to be moved to...Ch. 8.1 - (a) Show that the beam of Prob. 8.41 cannot be...Ch. 8.1 - Two 8-kg blocks A and B resting on shelves are...Ch. 8.1 - Prob. 8.44PCh. 8.1 - Prob. 8.45PCh. 8.1 - Two slender rods of negligible weight are...Ch. 8.1 - Two slender rods of negligible weight are...Ch. 8.2 - The machine part ABC is supported by a...Ch. 8.2 - Prob. 8.49PCh. 8.2 - Prob. 8.50PCh. 8.2 - Prob. 8.51PCh. 8.2 - Prob. 8.52PCh. 8.2 - Solve Prob. 8.52 assuming that the end of the beam...Ch. 8.2 - Prob. 8.54PCh. 8.2 - Prob. 8.55PCh. 8.2 - Block A supports a pipe column and rests as shown...Ch. 8.2 - A 200-lb block rests as shown on a wedge of...Ch. 8.2 - Prob. 8.58PCh. 8.2 - Prob. 8.59PCh. 8.2 - Prob. 8.60PCh. 8.2 - Prob. 8.61PCh. 8.2 - An 8 wedge is to be forced under a machine base at...Ch. 8.2 - Prob. 8.63PCh. 8.2 - A 15 wedge is forced under a 50-kg pipe as shown....Ch. 8.2 - A 15 wedge is forced under a 50-kg pipe as shown....Ch. 8.2 - Prob. 8.66PCh. 8.2 - Prob. 8.67PCh. 8.2 - Prob. 8.68PCh. 8.2 - Prob. 8.69PCh. 8.2 - Prob. 8.70PCh. 8.2 - Prob. 8.71PCh. 8.2 - The position of the automobile jack shown is...Ch. 8.2 - Prob. 8.73PCh. 8.2 - Prob. 8.74PCh. 8.2 - In the vise shown, the screw is single-threaded in...Ch. 8.2 - Prob. 8.76PCh. 8.3 - A lever of negligible weight is loosely fitted...Ch. 8.3 - Prob. 8.78PCh. 8.3 - 8.79 and 8.80 The double pulley shown is attached...Ch. 8.3 - Prob. 8.80PCh. 8.3 - 8.81 and 8.82 The double pulley shown is attached...Ch. 8.3 - Prob. 8.82PCh. 8.3 - Prob. 8.83PCh. 8.3 - The block and tackle shown are used to lower a...Ch. 8.3 - Prob. 8.85PCh. 8.3 - Prob. 8.86PCh. 8.3 - Prob. 8.87PCh. 8.3 - 8.87 and 8.88 A lever AB of negligible weight is...Ch. 8.3 - Prob. 8.89PCh. 8.3 - Prob. 8.90PCh. 8.3 - Prob. 8.91PCh. 8.3 - Prob. 8.92PCh. 8.3 - Prob. 8.93PCh. 8.3 - Prob. 8.94PCh. 8.3 - Prob. 8.95PCh. 8.3 - Prob. 8.96PCh. 8.3 - Solve Prob. 8.93 assuming that the normal force...Ch. 8.3 - Prob. 8.98PCh. 8.3 - Prob. 8.99PCh. 8.3 - A 900-kg machine base is rolled along a concrete...Ch. 8.3 - Prob. 8.101PCh. 8.3 - Prob. 8.102PCh. 8.4 - A rope having a weight per unit length of 0.4...Ch. 8.4 - A hawser is wrapped two full turns around a...Ch. 8.4 - Two cylinders are connected by a rope that passes...Ch. 8.4 - Prob. 8.106PCh. 8.4 - The coefficient of static friction between block B...Ch. 8.4 - Prob. 8.108PCh. 8.4 - A band belt is used to control the speed of a...Ch. 8.4 - Prob. 8.110PCh. 8.4 - The setup shown is used to measure the output of a...Ch. 8.4 - A flat belt is used to transmit a couple from drum...Ch. 8.4 - Prob. 8.113PCh. 8.4 - Prob. 8.114PCh. 8.4 - The speed of the brake drum shown is controlled by...Ch. 8.4 - The speed of the brake drum shown is controlled by...Ch. 8.4 - Prob. 8.117PCh. 8.4 - Bucket A and block C are connected by a cable that...Ch. 8.4 - Prob. 8.119PCh. 8.4 - Prob. 8.120PCh. 8.4 - 8.121 and 8.123 A cable is placed around three...Ch. 8.4 - Prob. 8.122PCh. 8.4 - Prob. 8.123PCh. 8.4 - Prob. 8.124PCh. 8.4 - Prob. 8.125PCh. 8.4 - Prob. 8.126PCh. 8.4 - The axle of the pulley is frozen and cannot rotate...Ch. 8.4 - The 10-lb bar AE is suspended by a cable that...Ch. 8.4 - Prob. 8.129PCh. 8.4 - Prove that Eqs. (8.13) and (8.14) are valid for...Ch. 8.4 - Complete the derivation of Eq. (8.15), which...Ch. 8.4 - Prob. 8.132PCh. 8.4 - Solve Prob. 8.113 assuming that the flat belt and...Ch. 8 - 8.134 and 8.135 The coefficients of friction are S...Ch. 8 - Prob. 8.135RPCh. 8 - Prob. 8.136RPCh. 8 - A slender rod with a length of L is lodged between...Ch. 8 - The hydraulic cylinder shown exerts a force of 3...Ch. 8 - Prob. 8.139RPCh. 8 - Bar AB is attached to collars that can slide on...Ch. 8 - Two 10 wedges of negligible weight are used to...Ch. 8 - A 10 wedge is used to split a section of a log....Ch. 8 - Prob. 8.143RPCh. 8 - A lever of negligible weight is loosely fitted...Ch. 8 - In the pivoted motor mount shown, the weight W of...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License