Concept explainers
(a)
The expression of
Answer to Problem 8.33P
The required expression is,
Explanation of Solution
Given Information:
The toroid is having square cross section,
Calculation:
The magnetic field intensity,
Conclusion:
The required expression is,
(b)
The expression of
Answer to Problem 8.33P
The required expression is,
Explanation of Solution
Given Information:
The toroid is having square cross section,
Calculation:
The magnetic flux density,
Conclusion:
The required expression is,
(c)
The expression of
Answer to Problem 8.33P
The required value is,
Explanation of Solution
Given Information:
The toroid is having square cross section,
Calculation:
The magnetic flux,
Conclusion:
The required value is,
(d)
The expressions of
Answer to Problem 8.33P
The required expressions are,
Explanation of Solution
Given Information:
The toroid is having square cross section,
Calculation:
The magnetic field intensity,
The magnetic flux density,
The magnetic flux,
Conclusion:
The required expressionsare,
(e)
The value of
Answer to Problem 8.33P
The required value is,
Explanation of Solution
Given Information:
The toroid is having square cross section,
Calculation:
The totalflux,
Conclusion:
The required value is,
Want to see more full solutions like this?
Chapter 8 Solutions
Engineering Electromagnetics
- Explain why a, a,=a° a a %3Darrow_forwardFrom the slope equation Find emf when the field current is l.3 A? Let that E-axis = y and Amer -axis =x m = y2-y-/x2-x1 Answer =562 varrow_forward(6) A parallel-plates capacitor with plate area of 100 cm? has a separation of 3mm between the pates. The separation is divided into three slabs, where each slab has 1 mm distance. The first slab is filled by air and has a constant of 1. The second slab is filled by polystyrene and has a constant of 2.5, while the third slab is filled by silicon dioxide and has a constant of 4. Compute the capacitance of the system. Note: for parallel slabs; Conductor 1 E = T 1 Air E1 83 Material A Material 3 Conductor Ans. C = 54 pFarrow_forward
- How many degrees are the current and voltage out of phase in a pure capacitive circuit?arrow_forwardSolve the following operations. (Final answer must be in polar form.)arrow_forwardHow many turns must be wound to obtain an air-core toroid with an average radius of 10 mm and a cross-sectional area of 10 mm2 and a coil with an inductance of 0.4 mH?Is a substitute solenoid possible for the same inductance value ? Please explain.arrow_forward
- Determine H at p la4,0.3,0)inthe Rield of. 8A filamentary current is dircted from infinity to the origin on the positive x-axir and then out ward to infinity along The arrangement is shown in figure The y-axés 8A 6,37 az Alm 8A Ans: H =arrow_forwardQUESTION 5 Consider the complex number defined below. Z, = 1-j Convert Z1 to polar form and specify its angle in the box below in units of degrees. DO NOT ENTER UNITS IN THE ANSWER BOX BELOW.arrow_forward1. Inductance. Consider the configuration of a wire with 90° bends as shown below. A small loop, with its sides of length a and width d = a/16 is placed with its plane lying along xz principal plane as shown. Stating all assumptions, determine mutual inductance between the loop and the wire. a/2 9/2 2aarrow_forward
- Noise due to inductive coupling can be reduced by twisting the wires carrying a signal. True Falsearrow_forwardGiven that Zo = 50 0, ZL = 10 Q and Zs = -j100 Q in the figure below, determine di and I1 such that there is no reflection at the reference terminal M-M’. %3D %3D Feedline Zo |ZL Zo M' Zo Zsarrow_forwardFind the inductance per unit length of a very long solenoid with a unit length of N windings. The permeability of the core is μ.arrow_forward
- Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning