The work and heat transfer for each process.
Answer to Problem 173RP
The heat transfer for the isothermal process 1–2 is
The work done during the process 1-2 is
The work done during the isentropic compression process 2-3 is
The heat transfer for the isentropic process 2–3 is
The work done during constant pressure compression process 3-1 is
The heat transfer during constant pressure compression process 3-1 is
Explanation of Solution
Write the expression to calculate the enthalpy change in process 1-2.
Here, pressure at process 1 is
Write the expression to calculate the ideal gas equation, to find mass of the air.
Here, mass of the air is m , volume at process 1 is
Write the expression to calculate the heat transfer for the isothermal process 1–2.
Here, enthalpy change in process 1-2 is
Write the expression to calculate the work done during the process 1-2
Write the expression to calculate the work done during the isentropic compression process 2-3
Here, mass of the air is m, internal energy at process 3 is
Write the expression to calculate the relative pressure at process 3
Here, relative pressure at process 2 is
Write the expression to calculate the volume at process 3
Write the expression to calculate the work done during constant pressure compression process 3-1
Here, volume at process 3 is
Write the expression to calculate the heat transfer during constant pressure compression process 3-1
Here, heat transfer during constant pressure compression process 3-1 is
Conclusion:
From Table A-1 “the molar mass, gas constant and critical point properties table”, obtain the gas constant
Substitute
Substitute 1.394 kg for m,
Substitute
Thus, the heat transfer for the isothermal process 1–2 is
Substitute
Thus, the work done during the process 1-2 is
From Table A-17, “Ideal-gas properties of air”, obtain the internal energy
Substitute
Refer to Table A-17, “Ideal-gas properties of air”.
Obtain the select the internal energy
Write the formula of interpolation method of two variables.
Here, the variables denoted by x and y are relative pressure and internal energy.
Show relative pressure and internal energy values from the Table A-17.
Relative pressure | Internal energy |
3.481 | 278.93 |
3.696 | ? |
3.806 | 286.16 |
Substitute
The value of internal energy process 1
Show temperature and initial internal energy values from the Table A-17.
Temperature | Internal energy |
3.481 | 390 |
3.696 | ? |
3.806 | 400 |
Substitute
The value of Temperature
Substitute 1.394 kg for m,
Thus, the work done during the isentropic compression process 2-3 is
The heat transfer for the isentropic process 2–3 is zero when entropy change remains unchanged for the isentropic compression process.
Thus, the heat transfer for the isentropic process 2–3 is
Substitute 1.394 kg for m,
Substitute
Thus, the work done during constant pressure compression process 3-1 is
Substitute 37 kJ for
Thus, the heat transfer during constant pressure compression process 3-1 is
Want to see more full solutions like this?
Chapter 7 Solutions
Thermodynamics: An Engineering Approach
- A piston-cylinder system has a compression ratio (biggest volume vl/smallest volume v2) of 8. Initial temperature Tl is 295 K undergoes a compression process in reversible and adiabatic manner. Determine the final temperature of T2.arrow_forward1) A piston-cylinder device contains 0.3 kg of air initially at 1.8 MPa and 350°C. The air is first expanded isothermally to 500 kPa, then compressed polytropically (with a polytropic exponent of 1.2) to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine the boundary work for each process and the net work of the cycle.arrow_forward1. Steam enters a nozzle at 400°C and 800 kPa with a velocity of 10 m/s, and leaves at 300°C and 200 kPa while losing heat at a rate of 25 kW. For an inlet area of 800 cm?, determine the velocity and the volume flow rate of the steam at the nozzle exit. Determine the following: a. Velocity at the exit (m/s) b. Volume flow rate (m³/s) From steam table: h,=3267.7 kJ/kg h,=3072.1 kJ/kg 400°C 300°C 800 kPa Steam v,=0.39429 m /kg 200 kPa v,=1.3163 m /kg 10 m/sarrow_forward
- Four pounds of steam initially dry and saturated expand isentropically in a non-flow process from an initial pressure of 275 psia to a final pressure of 125 psia. Find its quality and determine the work done in BTU/lb.arrow_forwardA piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at 400 kPa and 350C with a volume of 0.3 m3. The steam is first expanded isothermally to 150 kPa, then compressed adiabatically to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine the net work and heat transfer for the cycle after you calculate the work and heat interaction for each process.arrow_forward3. Initially, 0.55 kg of air is contained in a piston-cylinder device at 2 MPa and 350°C. The air is first expanded isothermally to 500 kPa, then compressed polytropically with a polytropic exponent of 1.2 to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine the heat transfer for each process and the net heat of the cycle (in kJ).arrow_forward
- A piston-cylinder assembly contains 3 lb of water vapor, initially at 300F and 20 lbf/in2 is compressed isothermally to a volume of 14ft3 . The system is then heated at constant volume to a final pressure of 140 lbf/in2 . During the isothermal compression 600 Btu of heat is transferred to the surroundings. Kinetic and potential energy effects are negligible. Show the P-v diagram for both processes, calculate the total work done, and the total change in entropy.arrow_forwardWater, initially a saturated liquid at 100°C, is contained in a piston-cylinderassembly. The water undergoes a process where it changes to the corresponding saturatedvapor state, during which the piston moves freely in the cylinder. If the change of state isbrought about by heating the water as it undergoes an internally reversible process atconstant pressure and temperature, determine the (a) work and (b) heat transfer per unitmass, each in kJ/kg.arrow_forwardA frictionless piston-cylinder assembly initially contains saturated liquid water at a pressure of 200 kPa. Then, 450 kJ of heat transfer occurs from a source with a temperature of 500 0C to water and some of the water evaporates at constant pressure. Show whether this state change is feasible or not by considering the increase of entropy principle.arrow_forward
- A piston-cylinder device initially contains 5 Ibm of liquid water at 20 psia and 70°F. The water is now heated at constant pressure by the addition of 5910.6 Btu of heat. Determine the entropy change of the water during this process.in psi. Select one: a. 6.330 Btu/R b. 8.712 Btu/R c. 5.105 Btu/R d. 7.821 Btu/Rarrow_forwardIn an experiment, a rigid container holds 3 kg of refrigerant-134a initially at 30°C and 180 kPa. The refrigerant is now cooled while being stirred until its pressure drops to 80 kPa. At the initial state, the specific entropy is (to 4 d.p.) in (to (insert unit symbol), specific volume is (insert unit symbol), 5 d.p.) in At the final state, the specific volume is (to 5 d.p.)(insert space then init symbol), the quality is (to 3 d.p.), the specific entropy is (to 3 d.p.)(insert space then init symbol) The entropy change of the refrigerant during this process is (to 3 d.p.) (insert space then init symbol). From the final answer, does the systen violates the second law of thermodynamics? (yes/no).arrow_forwardAn insulated vertical cylinder-piston device contains 0.8 m3 of refrigerant 134a at 1.2 MPa and 120 ° C. With a linear (compression) spring, all of its force is applied to the plunger at that moment. A valve connected to the cylinder opens and refrigerant escapes. The spring is loosened as the plunger is lowered, and the pressure and volume drop to 0.6 MPa and 0.5 m3, at the end of the process. Determine: a) the amount of refrigerant that escaped b) the final temperature of the coolantarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY