A liquid of density
The dimensionless relationship for
Answer to Problem 67P
The dimensionless relationship for
Explanation of Solution
Given information:
The number of variable parameters is
Expression for number of pi terms,
Here, number of variable parameters is
Substitute
Expression for first pi terms,
Here, pressure difference is
Expression for second pi terms,
Here, dynamic viscosity is
Expression for third pi terms,
Here, volume flow rate is
Expression for pressure,
Here, force is
Substitute
Expression for dimension diameter,
Expression for density,
Here, mass is
Substitute
Expression for angular velocity,
Substitute
Expression for dynamic viscosity,
Substitute
Expression for dimension of volume flow rate,
Substitute
Expression for relation of
Calculation:
Substitute
Compare the exponent of
Compare the exponent of
Compare the exponent of
Substitute the
Substitute
Compare the exponent of
Compare the exponent of
Compare the exponent of
Substitute the
Substitute
Compare the exponent of
Compare the exponent of
Compare the exponent of
Substitute the
Substitute
Conclusion:
The dimensionless relationship for
Want to see more full solutions like this?
Chapter 7 Solutions
Fluid Mechanics: Fundamentals and Applications
- When a sphere falls freely through a homogeneous fluid, it reaches a terminal velocity at which the weight of the sphere is balanced by the buoyant force and the frictional resistance of the fluid. Make a dimensional analysis of this problem and indicate how experimental data for this problem could be correlated. Neglect compressibility effects and the influence of surface roughness.arrow_forwardWhen a fluid flows slowly past a vertical plate of height h and width b, pressure develops on the face of the plate. Assume that the pressure, p, at the midpoint of the plate is a function of plate height and width, the approach velocity V, and the fluid viscosity u and fluid density p. Make use of dimensional analysis to determine how the pressure, p will be formed with a dimensionless group. (Take b, V. p as repeating variables). Select one: O a. n1 = p /V² p O b. n1 = p/Ve O c.n1 = p/Vp? O d. 11 = p/V² p²arrow_forwardProblem 1: The discharge pressure (P) of a centrifugal pump shown below is a function of flow rate (Q), impeller diameter (D), fluid density (p), and impeller angular speed (12). P = f (Q. D, p. 92). Use the Buckingham pi technique to rewrite this function in terms of dimensionless parameters, 1 g (n₂). P= P(Q,D, Dimensions 2) N= 5 Q. Parrow_forward
- A liquid of density ? and viscosity ? is pumped at volume flow rate V· through a pump of diameter D. The blades of the pump rotate at angular velocity ? . The pump supplies a pressure rise ΔP to the liquid. Using dimensional analysis, generate a dimensionless relationship for ΔP as a function of the other parameters in the problem. Identify any established nondimensional parameters that appear in your result. Hint: For consistency (and whenever possible), it is wise to choose a length, a density, and a velocity (or angular velocity) as repeating variables.arrow_forwardConsider a boundary layer growing along a thin flat plate. The boundary layer thickness & at a downstream distance x is a function of x, the fluid density p, dynamic viscosity, and free stream velocity V. Use Buckingham's theorem with p, x and V as repeating variables, to obtain the relationship between dimensionless parameters Is. Figure 3.2arrow_forward: The discharge pressure (P) of a gear pump (Fig. 3) is a function of flow rate (Q), gear diameter (D), fluid viscosity (µ) and gear angular speed (w). P = f (Q, D, H, 0). Use the pi theorem to rewrite this function in terms of dimensionless parameters. Suction Discharge Fig. 3: Gear pump P, Qarrow_forward
- Force F is applied at the tip of a cantilever beam of length L and moment of inertia I Fig. . The modulus of elasticity of the beam material is E. When the force is applied, the tip deflection of the beam is z d.Use dimensional analysis to generate a relationship for zd as a function of the independent variables. Name any established dimensionless parameters that appear in your analysisarrow_forwardThe conduction heat transfer in an extended surface, known as a fin, yields the following equation for the temperature T, if the temperature distribution is assumed to be one-dimensional in x, where x is the distance from the base of the fin, as shown in figure: To Fin >X T(x) h,T Heat Loss d²T_hp (T-T) = 0 dx² ΚΑ dT dx = 0 Here, p is the perimeter of the fin, being 2R for a cylindrical fin of radius R; A is the cross-sectional area, being R2 for a cylindrical fin; k is the At x = 0: T = T₁ dT At x=L: :0 dx thermal conductivity of the material; T is the ambient fluid temperature; and h in the convective heat transfer coefficient. The boundary conditions are as follows: where L is the length of the fin. Solve this equation to obtain 7(x) by using Euler's method for R=1cm, h= 20 W/m².K, k = 15 W/m-K, L = 25 cm, T₁ = 80°C, and T = 20°C.arrow_forwardThe thrust force, F generated by a propeller is found to depend on the following parameters: diameter D, forward velocity u, density p, viscosity u and rotational speed N. Determine the dimensionless parameters to correlate the phenomenon.arrow_forward
- The time t d to drain a liquid from a hole in the bottom of atank is a function of the hole diameter d , the initial fluidvolume y 0 , the initial liquid depth h 0 , and the density ρ andviscosity μ of the fluid. Rewrite this relation as a dimensionlessfunction, using Ipsen’s method.arrow_forwardProblem 4: The power P developed by a wind turbine is a function of diameter D, air density p, wind speed V, and rotational rate @. Viscous effect is negligible. (4a) Rewrite the above relationship in a dimensionless form; (4b) In a wind tunnel, a small model with a diameter of 90cm, rotating at 1200 RPM (revolution per minute), delivered 200 watts when the wind speed is 12m/s. The data are to be used for a prototype of diameter of 50m and wind speed of 8 m/s. For dynamic similarity, what will be (i) the rotational speed of the prototype turbine? (ii) the power delivered by the prototype turbine? Assume air has sea-level density.arrow_forwardQ2/ A car wheel is supposed to be travelling at a speed of 80 mile per hour in the air. A scaled model (1:4) is tested in water instead of air and is supposed to have dynamic similarity. a) Determine the model speed in water b) then find the force ratio of the model to prototype if you know that: (pair = 1.22 kg/m³, µair = 1.78 x 10- 5 N.s/m?, Pwater 998 kg/m², µwater = 0.001 N.s/m²).arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning