Concept explainers
Find the frontal area of the car in SI unit and U.S. Customary unit.
Answer to Problem 50P
The frontal area of the car in inches is
Explanation of Solution
Given data:
The height of the car
The width of the car
Formula used:
Formula to calculate the frontal area of the car is,
Here,
Calculation:
Total frontal area:
Formula to calculate the total frontal area of the car is,
Here,
Substitute
Area of the squares in which the parts of the car is not touched:
Refer to the figure 7.50, the height and width of the car is divided as slots. Therefore,
For 1 slot, the height (h) is:
For 1 slot, the width (w) is:
From the figure 7.50, approximately the total number of slots which is not touching the parts of car is 48.
Formula to calculate the area of the squares which is not touched by the parts of car is,
Here,
Substitute
Substitute
The SI unit of the frontal area of the car is,
The U.S. Customary unit of the frontal area of the car is,
Therefore, the frontal area of the car in SI unit and U.S. Customary unit is
Conclusion:
Thus, the frontal area of the car in SI unit, U.S. Customary unit and in inches is
Want to see more full solutions like this?
Chapter 7 Solutions
ENGINEERING FUNDAMENTALS
- Estimate the frontal area of the car shown in the accompanying figure.arrow_forwardThe following exercises are designed to help you become aware of the significance of various dimensions around you. You see these dimensions every day, but perhaps you never looked at them with the eyes of an engineer. Measure and discuss the significance of the dimensions of thefollowing items.a. The dimensions of your bedroom or living roomb. The dimensions of the hallwayc. The window dimensionsd. The width, height, and thickness of your apartment doors or dormitory doorse. The distance from the floor to the doorknobf. The distance from the floor to the light switchesg. The dimensions of your deskh. The dimensions of your bedi. The distance from the floor to the bathroom sinkj. The distance from the tub surface to the showerheadarrow_forwardDetermine the density, specific volume, and volume of an object that weighs 3N 2 in water and 4N in oil with specific gravity of 0.83 draw figurearrow_forward
- 50 N SCALE 50 N with a The figure shows two masses weight of 50 H, Suspended off the edge of a table onnected to Spring Scale. All objects are at rest. What is the reading on the scale? B) What is the het force on the spring scale? aarrow_forwardEvaluate each of the following to three significant figures and express each answer in SI units using an appropriate prefix: (a) (684 um)/(43 ms). (b) (28 ms)(0.0458 Mm)/(348 mg). (c) (2.68 mm)(426 Mg).arrow_forwardFor the machined object shown in the figure, whose material has a density of 7542 kg/m3, determine: a) The position of the object's center of gravity with respect to the y-axis, in millimeters 16 mm 40 mm 24 mm 70 mm y 50 mm 80 mm -38 mm 50 mm x b) The position of the object's center of gravity with respect to the z-axis, in millimetersarrow_forward
- You're calculating the volume of a cube with an edge length of 0.250 inches. Which of the following should be used to express the cube's volume? Assume a round-up rule if the digit in the next lower decimel place is "5" or greater. Group of answer choices 1.56E-2 cubic inches 1.6E-2 cubic inches 1.563E-2 cubic inchesarrow_forwardThe given are as follows: 240 mm 50 mm 400 mm 150 mm 150 mm 50 mm 50 mmarrow_forwardUse lincar splines interpolation with the data given below, to calculate the fuel economy at aspeed of (a) 30 mph (b) 65 mph. Speed (mph) Fuel economy (mpg) 10 25 40 55 70 12 26 28 30 24 Use 4 decimal places.arrow_forward
- Compute the deflection (in inches) of a structural member made of aluminum (please see figure) if a load of 500 lb is applied to the bar. The member has a uniform rectangular cross section with the dimensions of ¼ in x 4 in, as shown. Show your calculations and result.arrow_forwardCalculate the volume of material used in making 100 ft of 4-in. type M, copper tubing.arrow_forwardNeed help! Image attached. A regulation tennis ball is made of an elastic material and can be modeled as a sphere. The center of the tennis ball is hollow, filled with pressurized air. You may assume the mass of air inside the tennis ball is negligible. The elastic portion of the tennis ball has a mass of 58 grams [g]. The outer diameter is 2.6 inches (in] and elastic material has a thickness of 3 millimeters (mm). What is the specific gravity of material used to form the tennis ball?arrow_forward
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning