(a)
The best suitable
Answer to Problem 6.8.6P
The best suitable
Explanation of Solution
Given:
The axial load is
The length of the column is
The moment at top in x-direction is
The moment at top in y-direction is
The moment at bottom in x-direction is
The moment at bottom in y-direction is
Calculation:
Write the equation to obtain the load factor.
Here, load factor is
Substitute
Write the equation to obtain factored bending moment at the bottom of the member for braced condition along x-axis.
Here, factored bending moment at bottom along x-axis is
Substitute
Write the equation to obtain factored bending moment at the top of the member for braced condition along x-axis.
Here, factored bending moment at top along x-axis is
Substitute
Write the equation to obtain factored bending moment at the bottom of the member for braced condition along y-axis.
Here, factored bending moment at bottom along y-axis is
Substitute
Write the equation to obtain factored bending moment at the top of the member for braced condition along y-axis.
Here, factored bending moment at top along y-axis is
Substitute
Write the equation to obtain the ultimate moment along x-axis.
Here, factor for braced condition is
Substitute
Write the equation to obtain the ultimate moment along y-axis.
Here, factor for braced condition is
Substitute
The unbraced length and effective length of the member are same.
Try
Write the expression to determine which interaction equation to use.
Here, load factor is
Substitute
Therefore,
Write the expression
Here, load factor is
Substitute
Further solve the above equation.
Hence it is safe to use
Try
Write the expression to determine the interaction equation to be used.
Here, load factor is
Substitute
Therefore,
Write the expression
Here, load factor is
Substitute
Further solve the above equation.
Hence, it is safe to use
Try
Write the expression to determine which interaction equation to use.
Here, load factor is
Substitute
Therefore,
Write the expression
Here, load factor is
Substitute
Further solve the above equation.
Hence, it is safe to use
Further check
Write the expression
Here, load factor is
Substitute
Further solve the above equation.
Hence, it is safe to use
Conclusion:
Thus, use
(b)
The best suitable
Answer to Problem 6.8.6P
The best suitable
Explanation of Solution
Calculation:
Write the equation to obtain the axial service load.
Here, load factor is
Substitute
Write the equation to obtain factored bending moment at the bottom of the member for braced condition along x-axis.
Here, factored bending moment at bottom along x-axis is
Substitute
Write the equation to obtain factored bending moment at the top of the member for braced condition along x-axis.
Here, factored bending moment at top along x-axis is
Substitute
Write the equation to obtain factored bending moment at the bottom of the member for braced condition along y-axis.
Here, factored bending moment at bottom along y-axis is
Substitute
Write the equation to obtain factored bending moment at the top of the member for braced condition along y-axis.
Here, factored bending moment at top along y-axis is
Substitute
Write the equation to obtain the ultimate moment along x-axis.
Here, factor for braced condition is
Substitute
Write the equation to obtain the ultimate moment along y-axis.
Here, factor for braced condition is
Substitute
The unbraced length and effective length of the member are the same.
Try
Write the expression to determine the interaction equation to be used.
Here, load factor is
Substitute
Therefore,
Write the expression
Here, load factor is
Substitute
Further solve the above equation.
Hence, it is safe to use
Try
Write the expression to determine which interaction equation to use.
Here, load factor is
Substitute
Therefore,
Write the expression
Here, load factor is
Substitute
Further solve the above equation.
Hence, it is safe to use
Try
Write the expression to determine which interaction equation to use.
Here, load factor is
Substitute
Therefore,
Write the expression
Here, load factor is
Substitute
Further solve the above equation.
Hence, it is safe to use
Further check
Write the expression
Here, load factor is
Substitute
Further solve the above equation.
Hence, it is safe to use
Conclusion:
Thus, use
Want to see more full solutions like this?
Chapter 6 Solutions
Steel Design (Activate Learning with these NEW titles from Engineering!)
- Check the slenderness of the steel section against Local Buckling. 340 mm Use Fy = 800 MPa. O Compact Slender I O Adequate 400 mm None of the choices 30 mm 20 mm 20 mmarrow_forwardThe beam shown in Figure has lateral support only at the ends. The uniform load is a superimposed dead load, and the concentrated load is a live load. Use A992 steel and select a W shape. The live load deflection must not exceed L/360. a. Use LRFD.b. Use ASD.arrow_forwardA column is formed by welding two A36 MC sections back-to- back. The column is 32 feet long. With respect to x-axis buckling, supports are hinged at the top, and fixed at the bottom. With respect to y-axis buckling, supports are pinned at both ends. Additionally, hinge supports are provided at the mid-height perpendicular to both axes. Use the recommended k-values. Below are the properties of a single MC section: A=6.45 in2, d=10 in, bf-3.32 in, x=0.990 in, Ix=102 in¹, ly=6.40 in, rx-3.99 in, ry=0.997 inarrow_forward
- The member shown in Figure P6.6-4 is part of a braced frame. The load and moments are computed from service loads, and bending is about the x axis (the end shears are not shown). The frame analysis was performed consistent with the effective length method, so the flexural rigidity. EI, was unreduced. Use Kx=0.9. The load and moments are 30 dead load and 70 live load. Determine whether this member satisfies the appropriate AISC interaction equation. a. Use LRFD. b. Use ASD.arrow_forwardThe rigid frame shown is unbraced. The members are oriented so that bending is about the strong axis. Support conditions in the direction perpendicular to the plane of the frame are such that Ky= 1.0. The beams are W16 x 57, and the columns are W10 x 100. A992 steel (E= 350 MPa and Fy= 450 MPa) is used. The axial compressive service DL= 400 KN, and the axial compressive service LL= 490 KN. Determine the allowable axial compressive design strength of column AB. Use the stiffness reduction factor if applicable. Use ASD. 4.60m 5.5 m 6.10marrow_forwardThe rigid frame shown is unbraced. The members are oriented so that bending is about the strong axis. Support conditions in the direction perpendicular to the plane of the frame are such that Ky = 1.0. The beams are W410 x 85, and the columns are W250 × 89. A992 steel is used, Fy=345 mPa. The axial compressive dead load is 750 kN and the axial compressive live load is 900 kN. Use the AISC alignment chart or Magdy I. Salama Formula for Kx. 4.5 m 5.5 m 6.0 m ly Cw Sx mm^2 mm^4 mm^3 1100 1510 A Ix rx Sy ry Zx Zy SECTION m mm^4 mm^3 378 mm^3 mm^3 mm^3 mm^9 1040 713 716 mm mm W250x89 4500 11400 143 W410x85 5500 10800 315 48.4 65.2 1230 574 1730 310 112 171 18 199 40.8 926 Which of the following best gives the axial strength of column AB? Use the NSCP 2015 LRFD specifications. O 2,340 kN 1,647 kN O 2,745 kN O 2,471 kNarrow_forward
- For the given properties of beam below. Design the reinforcements of the beam. d'=75 mm b=400 mm d=580 mm fc'=35 MPa fy=320 MPa Mu=1000000000N mm Input is 0 in As' if compression bars are not needed. A. USE NSCP 2001, As = mm2, As' = mm2 B. USE NSCP 2015, As = mm2, As' = mm2 %3Darrow_forwardHow much service live load, in kips per foot, can be supported? The member weight is the only dead load. The axial compressive load consists of a service dead load of 10 kips and a service live load of 20 kips. Do not consider moment amplification. Bending is about the x axis, and the steel is A992. a. Use LRFD. b. Use ASD.arrow_forwardThe rigid frame shown is unbraced. The members are oriented so that bending is about the strong axis. Support conditions in the direction perpendicular to the plane of the frame are such that Ky = 1.0. The beams are W410 x 85, and the columns are W250 x 89. A992 steel is used, Fy=345 mPa. The axial compressive dead load is 750 kN and the axial compressive live load is 900 kN. Use the AISC alignment chart or Magdy I. Salama Formula for Kx. B 4.5 m 5.5 m 6.0 m Sx ly Sy mm^4 mm^3 A Ix Zx Zy J Cw rx ry mm^3 mm^3 mm^3 mm^g SECTION mm^2 mm^4 mm^3 mm mm W250x89 4500 W410x85 5500 10800 11400 143 1100 112 48.4 378 65.2 1230 574 1040 713 315 1510 171 18 199 40.8 1730 310 926 716 Which of the following best gives the allowable axial strength of column AB? Use the NSCP 2015 LRFD specifications. O 1,647 kN O 2,471 kN O 900 kNarrow_forward
- The rigid frame shown is unbraced. The members are oriented so that bending is about the strong axis. Support conditions in the direction perpendicular to the plane of the frame are such that Ky = 1.0. The beams are W410 x 85, and the columns are W250 × 89. A992 steel is used, Fy=345 mPa. The axial compressive dead load is 750 kN and the axial compressive live load is 900 kN. Use the AISC alignment chart or Magdy I. Salama Formula for Kx. B 4.5 m 5.5 m 6.0 m Sx mm^2 mm^4 mm^3 1100 L A Ix Sy Zx Cw ly mm mm^4 mm^3 112 48.4 Zy mm mm^3 mm^3 mm^3 mm19 1040 SECTION ry 65.2 1230 574 713 W250x89 4500 11400 W410x85 5500 10800 315 143 378 1510 171 18 199 40.8 1730 310 926 716 Which of the following best gives the allowable axial strength of column AB? Use the NSCP 2015 LRFD specifications. O 1,647 kN 2,471 kN O 900 kNarrow_forwardDetermine the maximum axial compressive service load that can be supported if the live load is twice as large as the dead load. Use AISC Equation E3-2 or E3-3. a. Use LRFD. b. Use ASDarrow_forward4. 2L100x100x8 are welded together to form a box section as shown. It is used as a compression member to support a vertical load, P. The column is hinged on its top and fixed at the bottom (k = 0.70). Determine the largest allowable P that the column can carry if it has an unsupported length of 4m. Use A36 steel (Fy = 248 MPa) Properties of an L100x100x8: Area = 1551 mm² Moment of Inertia, Ix = ly 1448 x 10³ mm4 Centroid, x = y = 27.37 mm Ans. 343.02 KN 8 100 + 100 CIVIL ENGINEERING-SYEEL DESSIONarrow_forward
- Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning