Concept explainers
Assume that the voltage drop across the resistor,
Want to see the full answer?
Check out a sample textbook solutionChapter 17 Solutions
Delmar's Standard Textbook Of Electricity
- VOFF = 0 VAMPL = 3.5 FREQ = 79.58k AC = V1 0 Rint 50 Vout Vout R1 1k HH 0 C1 1n ши ® L1 1m 0arrow_forwardIn a series AC resistive circuit: a) voltage leads current by 90°(degrees). O b) current leads voltage by 90°(degrees). © current and voltage are in phase. d) d current and voltage cancel.arrow_forwardTwo impedance coils A and B are connected in series to a 111-volt ac source. Coil A has a resistance of 12 ohms and an inductive resistance of 16 ohms. Coil B has a resistance of 24 ohms and an inductive reactance of 10 ohms. Calculate the voltage drop across each coil. Only in rectangular formarrow_forward
- Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707arrow_forwardNote: You are attempting question 3 out of 12 For the same alternator, the ratio of rated KVA, when connected as 3-phase winding alternator to when connected as single phase alternator (by utilizing all the coils) is, (a) 1.33 (b) 0.50 (c) 0.67 (d) 1.50 Answer A D Submit 27°C realme Shot by Gowthamnag 2021/10/30 11:55 O O O Oarrow_forwardA utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. What is the minimum AC voltage rating of each capacitor? Answer is 1200 volts. What is the current flow through the circuit? And what is the minimum kVAR rating of each capacitor?arrow_forward
- Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.arrow_forwardA single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)arrow_forwardConvert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)arrow_forward
- A sinusoidal voltage with effective value (73 V), and a Frequency its value (80 Hz), was applied on a series circuit that consists of a coil with inductance of value (0.05 H), and a resistor of value (5 0). Calculate: 1. The maximum value of the voltage? 2. The inductive reactance of the coil? 3. The electric impedance of the circuit? 4. The maximum value of the generated current in the circuit? 5. The phase angle? 6. The power factor? 7. The power dissipated inside the coil? 8. Draw a diagram showing the results?arrow_forwardWhen a resistor is connected across the terminals of an ac generator (117 V) that has a fixed frequency, there is a current of 0.332 A in the resistor. When an inductor is connected across the terminals of the same generator, there is a current of 0.365 A in the inductor. When both the resistor and the inductor are connected in series between the terminals of this generator, what is (a) the impedance of the series combination and (b) the phase angle between the current and the voltage of the generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number (b) Number Buda i Vrms R Irms.R Circuit 1 Units Units Vrms. Irms, L Circuit 2 > L Vrms R www Circuit 3arrow_forwardPLEASE RESOLVE! THE FINAL ANSWER MUST BE IN THE CHOICES. DC/AC MOTOR (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATIONS NEEDED. ANSWER IN 2 DECIMAL PLACES. BOX THE FINAL ANSWER.) A current of (120-j150) A flows through a circuit when applied voltage is (8 + j12) V. A. What is the magnitude of the circuit impedance: a. 0.0635 ohm b. 0.0256 ohm c. 1.52 ohm d. 1.325 ohm B. What is the reactive power? a. 825.75 VAR b. 525.68 VAR c. 639.75 VAR d. 438.72 VARarrow_forward
- Power System Analysis and Design (MindTap Course ...Electrical EngineeringISBN:9781305632134Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. SarmaPublisher:Cengage Learning