Concept explainers
A
a.
The stress in the steel rod.
Answer to Problem 10.1P
Explanation of Solution
Given information:
Diameter of steel rod
Length of rod
Elongation of rod
Tensile load
Proportional limit of steel
Formula used:
We know that stress is given by,
Calculation:
The stress of the steel rod is follows,
Conclusion:
Therefore, the stress in the steel rod is
b.
The strain of the rod.
Answer to Problem 10.1P
Explanation of Solution
Given information:
Diameter of steel rod
Length of rod
Elongation of rod
Tensile load
Proportional limit of steel
Formula used:
Strain of the rod is given by,
Calculation:
Conclusion:
Therefore, the strain of the rod is given by
c.
The modulus of Elasticity of the steel rod.
Answer to Problem 10.1P
Explanation of Solution
Given information:
Diameter of steel rod
Length of rod
Elongation of rod
Tensile load
Proportional limit of steel
Formula used:
Modulus of Elasticity is given by,
Calculation:
The modulus of elasticity of the rod is follows,
Conclusion:
Therefore, the modulus of elasticity of the steel rod is
Want to see more full solutions like this?
Chapter 10 Solutions
Applied Statics and Strength of Materials (6th Edition)
Additional Engineering Textbook Solutions
Engineering Mechanics: Dynamics (14th Edition)
Mechanics of Materials
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Applied Fluid Mechanics (7th Edition)
Engineering Mechanics: Statics
Mechanics of Materials (10th Edition)
- The following data were obtained from a standard tensile stress test on a mild steel specimen. Graph the result and determine proportional limit stress and Young’s Modulus.arrow_forwardStress strain behavior of a cast iron with a diameter of 15.8mm and gauge length of 60.80mm is shown in the graphs. Find the ductility in percent elongationarrow_forwardA specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?arrow_forward
- A straight bar of uniform cross sectionis tested in tension. The bar's cross sectional is 6.5 square centimeters and a length of 4 m. When the tensile load reaches 85kN, the total elongation is 2.5mm. What is the stress and the modulus of elasticity of the bar?arrow_forwardDraw a typical stress vs strain tensile test curve for the following materials (two seperate graphs) and label the axis. A ductile metallic test specimen that is stretched to failure displaying a characteristic yield point and show the following parts on the curve. 1- Yield point 2- Ultimate Tensile Strength 3- Breaking point 4- Elastic Region 5- Plastic Region 6- Necking regionarrow_forwardIn a tensile test for an aluminum alloy, the sample is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. Now that the axial stress of the sample under a tensile load of 9 kips is below material's proportional limit, please calculate the elongation of the sample under the tensile load of 9 kips: ____ inch. Pay attention to units and calculate your answer to 4 decimal place.arrow_forward
- The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 150 kN. - Length of the specimen is 24 mm. - The yield strength is 78 kN/mm2. - The percentage of elongation is 42 %. Determine the following iii) Stress under an elastic load of 14 kN, iv) Young's Modulus if the elongation is 1.7 mm at 14 kN and (v) Final diameter if the percentage of reduction in area is 26 %. I wont answer for this three questions only: 1)Final Area of the Specimen at Fracture (in mm) 2)Final Diameter of the Specimen after Fracture (in mm) 3)Initial Cross-sectional Area (in mm2)arrow_forwardA Copper specimen of circular cross-section is subjected to a tensile test. The data obtainedare:Length of Specimen = 329 mm;Diameter of Specimen = 39 mm;Load at Yield Point = 130 kN;Maximum Load = 219 kN;Load at fracture = 118kNDetermine the following:1) Find initial area of the test specimen2) Yield Stress3) Ultimate Stress4) Fracture stress5) Find the strain for 0.058mm elongation.6) Mark Yield stress, Ultimate stress and Fracture stress on a Stress-Strain diagram.arrow_forwardThe following data were obtained from the tensile test of Aluminum alloy. The initial diameter of testspecimen was 0.505 inch and gauge length was 2.0 inch. Plot the stress strain diagram and determine(a) Proportional Limit (b) Modulus of Elasticity (c) Yield Stress at 0.2% offset (d) Ultimate Stress and(e) Nominal Rupture Stress.arrow_forward
- A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 mis under tension. If the wire length extension is 2.5 mm, calculate the stress in thewire. Give your answer in N/m2to 2 decimal places.arrow_forwardIn a tensile test on a steel tube of external diameter 18 mm and internal diameter 12 mm, an axial pull of 2 kN produces stretch of 6.72x 10^-3 mm in a length of 100 mm and a lateral contraction of 3.62x10^-4mm in outer diameter. Calculate the values of three modulus and Poisson's ratio of the materialarrow_forwardA stress-strain diagram for a tension test of an alloy steel sample is shown in the diagram below. The initial sample diameter is 0.502”, the diameter of the fractured sample is 0.412”, the original gage length is 2.00” and the final length after fracture is 2.78”. Determine/ calculate the following: (a) The stress at the proportional limit. (b) The modulus of elasticity (E). (c) The yield stress using the 0.2% offset method. (d) Theultimatetensilestrength. (e) The rupture stress. (f) The percent reduction in area. (g) The percent elongation. (h) Is the material considered ductile or brittle?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY