Please solve this problem When the ON/OFF switch is falseLadder logic programON/OFFIESTOP36LEVEL SWITCH36LS136LS236Select one:a.STARTTJMO b.O C.O d.e.MCRPL1()SOL(¹)SOL-(u)(MCROutputs M, PL1, and SOL become falseOutputs M and PL1become false, and output SOL remains at its last stateNo change in the output will occurNone of the choicesSOL output will be de-energized

The given PLC ladder diagram is shown below.

When the ON/OFF switch is false ON/OFF 36 STOP LS1 36 LEVEL SWITCH 36 LS2 36 Select one: a. O b. 0 с. Ladder logic program (MCR O d. O e. START PL1 SOL SOL (u) (MCR Outputs M, PL1, and SOL become false Outputs M and PL1become false, and output SOL remains at its last state No change in the output will occur None of the choices SOL output will be de-energized

When the ON/OFF switch is false ON/OFF 36 STOP LS1 36 LEVEL SWITCH 36 LS2 36 Select one: a. O b. 0 с. Ladder logic program (MCR O d. O e. START PL1 SOL SOL (u) (MCR Outputs M, PL1, and SOL become false Outputs M and PL1become false, and output SOL remains at its last state No change in the output will occur None of the choices SOL output will be de-energized

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

d) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Using a K-map, simplify the output expression for the circuit in the figure. Draw the logic diagram for the simplified logic expression derived in the previous procedure. Construct the simplified circuit in the previous procedure. Use a DIP switch for each input.
Q2/A) Design 8x1 multiplexer using 2x1 multiplexer? Q2 B)Simplify the Logic circuit shown below using K-map then draw the Simplified circuit? Q2/C) design logic block diagram for adding 12 to 5 using full adder showing the input for each adder?
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
logic circuit diagram for fabinaaci counter that gives output in fabinaaci sequence.upto 2 digits please mentions the gates and ics used in circuit.
An X-input exclusive-OR gate and a Y-input exclusive-OR gate (where X=3, Y=4 have their outputs connected to a 2-input exclusive-NORgate. Do the following:a) Draw the logic diagram and analyze the logic expression of the output (in standard SOPform).b) List out all essential prime implicants.
Electrical Engineering Draw 2, 1 bit ALUS to create a basic 2 bit ALU. the carry out and carry in bits must ripple across. The ALU should subtract/add, logical NOR, logical AND, and logical OR. Draw out the adding logic circuit
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
6. For the follow logic circuit system, the output f is: 5 (A) ab. (B) a + b. (C) a'+b'. (D) a'b'. a b