What effective walkway width is needed if the hourly passenger demand of 8,750  is to be serviced at a LOS B? Provide your response to the nearest tenth of a foot.

Q: Problem 5: Develop a flow chart of the process for determining the bar cutoff locations in flexural…

A: To develop:A flowchart showing the process for determining bar cutoff locations in flexural member

Q: Problem: A 2 story bank is constructed with reinforced masonry walls and the floor and structural…

A: A "2-story bank" is a building that houses a bank and has two stories or levels and the bank has two…

Q: How do we know if the world is on an unsustainable path? Are we on a sustainable path?

A: Determining whether the world is on an unsustainable path involves assessing various factors across…

Q: Calculate the discharge for a flow depth of 0.85 m in a trapezoidal open channel with bottom width 1…

A: Givven data:

Q: Conjugate Beam: (constant EI) A t L Find Ou, Su using Conjugate x * PL Beam method

A:

Q: It is required to design a combined footing for two RCC columns spaced at 4.5 m C/C. The columns are…

A:

Q: 6-1. Draw the influence lines for (a) the moment at C, (b) the vertical reaction at A, and (c) the…

A: Pass a unit load over the beam starting from B, then form an equation and draw the influence lines…

Q: The Tatooine community will landfill plastic along with the inert material and rubber. Assuming that…

A:

Q: For the connection shown in the figure. A 1/2 in thick tension plate is connected to two 3/8 in…

A:

Q: B. Find forces in members CF, CG and GE of truss (b) using appropriate sections 30 k 30 k 41 30 k- F…

A:

Q: Following results were recorded from a consolidation test on a specimen of saturated clay, each load…

A: After subjecting a saturated clay specimen to a consolidation test, each load was held constant for…

Q: P10.045 For the beam and loading shown, use discontinuity func (a) the slope A of the beam at A and…

A:

Q: From the given cable shown. Determine the minimum tension in the cable in kips Let w = 35 kips/ft D…

A:

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: LL = 25 kNDL = 50 kNU = 1.0Plate dimensions: 10 x 100 mmFactored load:P = 1.2 DL + 1.6 LL = (1.2x50)…

Q: I. Determine the rotation at point A and the deflection at the free end using moment diagram by…

A:

Q: 1. A rectangular beam is 15 in. wide and 30 in. deep. For f= 4000 psi and f = 60,000 psi, determine…

A:

Q: A researcher was observing traffic along one lane of a rural highway. During a 1 minute time…

A:

Q: It is required to design a combined footing for two RCC columns spaced at 4.5 m C/C. The columns are…

A:

Q: A stable layer of air above an unstable layer would have what effect on the dispersion of a ground…

A: Objective:To explain how a stable layer of air above an unstable layer would have an effect on the…

Q: Show complete solution and clear explanation thank you A flexible pavement having a thickness of…

A:

Q: A structural designer wishes to locate the roller support B such that the beam AD) in Fig. P6.4-13…

A:

Q: Major projects require a great deal of pre-planning so that all employees and subcontractors can use…

A: Construction management should actively follow the most effective use of personnel, materials, and…

Q: Questions #1 Water flows at the rate of 0.16 L/s through a 200 mm diameter pipe. If its Viscosity…

A:

Q: researcher was positioned at the side of a 2-lane rural highway. He recorded the volume of…

A: To ascertain the quantity, movements, and types of road vehicles at a certain site, traffic volume…

Q: The design of a city water supply system is shown in the figure. Reservoir A need to supply 0.0938…

A:

Q: The uniform wire is bent into the shape shown and held by the frictionless pin at O. Determine the…

A: For the equilibrium to satisfy the centroid of the section should pass through O

Q: An industrial plant needs 1, 383,739 gallon of water per day which must be pumped  from a lake to a…

A:

Q: The figure below shows a proposed foundation site, with 10 ft of sand overlying 20 ft of clay with…

A:

Q: A statically indeterminate beam AB of length 4 m having a fixed support at A and roller at B carries…

A: Determine the degree of indeterminacy and support moment reaction at A.

Q: From the given cable shown. Determine the maximum tension in the cable in kips if: Let w = 39…

A:

Q: A rigid pavement is to be used to carry a wheel load of 49KN, the allowable tensile stress of the…

A: The wheel load on the rigid pavement = 49 kNThe allowable tensile stress of concrete = 1.4…

Q: A bearing plate is used to support a W 21 x 68 beam having a spam of 6m which carries a uniformly…

A: A bearing plate is used to support a W 21 x 68 beam having a spam of 6m which carries a uniformly…

Q: 1. Determine reaction forces. 2. Draw shear diagram. 3. Draw moment diagram. 50 kN/m 3m 30 kN/m 3m…

A:

Q: Below is a transit and tape survey notes of a lot. Compute the error of deflection angle Station 1 2…

A:

Q: why elastic constants (E,K,G) are more predictable than fck (or) Sigma y (or) shear strength?

A: Elastic constants such as Young's modulus (E), bulk modulus (K), and shear modulus (G) are often…

Q: Determine the forces in members CD, DH,GH, HI, BH, and BC. Also determine whether they are in…

A:

Q: A beam has a natural frequency of 1.179 hz and a damping ratio of 5%. It’s subjected to loads that…

A: Natural frequency = 1.179 hzDamping ratio = 5% = 0.05Displacement due to static loads = 2.38 mmLoads…

Q: 1. Draw the shear and homent diagrams for the beam shown in Figure 1. EI is constant. Neglect the…

A:

Q: 2. A plane truss is loaded as shown in fig.2. Determine the forces in each member of the truss by…

A: Determine the force in each members of the truss using method of joints.

Q: A double angle ISA 75mm x 75mm x 8mm back- to-back welded to one side of a 12mm gussethave allowable…

A:

Q: What are the equations that describe the ductile creep of rocks at low, moderately low (<200 MPa)…

A: Creep is the term for a material's long-term strain response.

Q: 2 kN/m 5 m 3 m 10 kN 2 m- B

A:

Q: 5. A disinfection process destroys E.coli in water. The influent c coliforms/mL. If the reactor…

A:

Q: the answer choices are given in the picture.... the answers provided are not even options from the…

A: Given span length= L = 30 ft Uniformly distributed live load= 110 Kips Uniformly distributed dead…

Q: 4. A flat site is underlain by two layers over rock. The top layer is a CL with thickness = 3m,…

A:

Q: Problem 2: The section of a prestressed double-tee concrete floor joist is shown is FIGURE-1. The…

A:

Q: The winch delivers a horizontal towing force F to its cable at A which varies as shown in the graph.…

A: Given that,the mass of the bucket is m= 72 kg,intial velocity is v1=4 m/s,time given is t=23 s,For…

Q: Calculate the total force (thrust) on the side of a filled to 5.6 m depth with sea water with a…

A:

Q: The beam of section and details shown in the below figure carries a dead load of WD-10 kN (include…

A:

Q: Explain the following concept related to pile foundations and use figures for illustration. *…

A: Compare and contrast the relative advantages and disadvantages of steel pipe piles and precast…

Highway Surveys and Location

Surveying is an operation in the civil engineering domain that requires collecting and identifying data regarding an area of land and topography. The data that is collected can be helped to plan and undertake the construction process. Civil engineers perform surveys to gather three-dimensional information regarding a particular area. Engineers specify several points on the surface of the earth and relationship between points, and the distance and angles between the points are evaluated. The data from this evaluation guides in drawing plans regarding buildings and structures.