2. A plane truss is loaded as shown in fig.2. Determine the forces in each member of the truss byusing method of joints. State whether the members are in tension (T) or compression (C).Equilateral triangleA2.2m3 KNBir ?+3KNEquilateraltriangles(Equal size)

Determine the force in each members of the truss using method of joints.

Answered: 2. A plane truss is loaded as shown in…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Use the Force Method to determine the forces in all eight members of the truss shown, and state whether they are in tension or compression. (Truss members BD and EC do not intersect.) Select member EC as the redundant member. AE is constant. 3 m 3 m D 12 kN 3 m
1. (5 Points) Find the trusses is members BC, BD, and CF for the truss shown in Figure. Indicate the tension or compression. The cross-sectional area of each member is 1600 mm². When: a = 3 b=4 F₁ = 60 KN F₂ =90kN a 1 A F₁ F₂ b 9 b
Determine the force on the EF and EG elements on the truss shown in the figure and consider P = 35kN. Final answer: EF force = 69.5kN T Force at EG = 250kN C
1.) The truss shown is made of steel members ( E = 29 x 106 psi ). Members AB and BC have cross- sectional areas of 0.80 in² and 0.64 in? respectively. For the loading shown, determine the elongation of both members B A 25 kips 5A Kips Figure #1
2.54 The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap A between the lower end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x 10-3. What is the length of the gap A? The cross-sectional areas are 300 mm? for rod AC and 250 mm² for rod BD. Use E = 200 GPa for steel. A B 0.75 m -1.5 m 2 m FIG. P2.53, P2.54
Using the method of joints, determine the force in each member of the truss shown below (solve for FAB, FAD, FBD, FDE, FBE, FBC, and FcE. Use the sign convention of negative for compression of the joint and positive for tension of the joint. 2000 lb -12 ft- 1000 lb 12 ft cl 8 ft D E -12 ft 6 ft 6 ft Hints: 1. The reaction at the roller support at E is 10,000 lbf upwards. 2. The reaction of the support at C is 7,000 lb, downwards.
where P=5kN Analyze trusss using method of joints. 1. what is the force in member DE? 2.what is the force in member BC? 3. what is the greatest force P that can be applied in the truss?
The portion of truss shown represents the upper part of a power transmission line tower. The 2.7 kN force is 60° from the vertical. For the given loading, determine all zero force members. a. Use the Method of Section to find the forces in members BC, EH and EJ; b. Use the Method of Joints to find the forces in members BD and DE; Answers: FBC = 0.9878 kN, T, FEH = 2.9228 kN, C, FEJ = 0.5841 kN, C, FBD = 1.3171 kN, T, FDE = 0.3576 kN, C 1.60 m -2.21 m- Bl 2.21 m- Al 0.60 m 0.60 m C 2.7 kN 1.20 m 1.2 kN H 0.60 m 0.60 m K -2.97 m- 1.2 kN 1.20 m N 1.2 kN M! 0.60 m 0.60 m R 1.2 kN 1.2 kN T
The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90 in2 for all the members. Determine the deformation sustained by members CG and FG
The truss ABC is constructed of three titanium (E Ti =17.4×10 3 ksi) members. A horizontal force of 1.8 kip and an unknown force P are applied to the truss at point B as shown. Member AB has a cross-sectional area of 0.1in 2 , member BC has a cross-sectional area of 0.0025ft 2 , and member AC has a cross-sectional area of 0.2 in2. b) Determine the magnitude of the force P that is required to displace the roller at point C to the right by .03 inches.
Determine the forces in members EH and El of the double Fink truss (positive if in tension, negative if in compression). Neglect any horizontal reactions at the supports and note that joints E and F divide DG into thirds. L D L E B A 20° K J I H 20° AK = KJ = JI = IH = HG = 3.4 m %3D %3D Answers: EH = i El
Use the joint method of analysing truss to calculate the forces in members AB, AE, BE, BC and EC of the truss shown in Figure 2. В A E 2 m 1 m 14 kN Figure 2

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

2. A plane truss is loaded as shown in fig.2. Determine the forces in each member of the truss by using method of joints. State whether the members are in tension (T) or compression (C). Equilateral triangle A 2.2m 3 KN +3KN 2.2m Equilateral triangles (Equal size)