The wire-mass system shown is constructed using 6061-T6 aluminum wire. Determine the minimum allowable wire diameter if the criterion for failure is based on yield tensile strength and the safety factor imposed on the design is SF = 2.5. Use the same diameter for both wires. Take m = 90 slugs, 01 = 35° and 0₂ = 50°. - A\ 0₁1 dmin number (rtol=0.01, atol=1e-05) AY 3 B 0₂ in 0000 2.

The wire-mass system shown is constructed using 6061-T6 aluminum wire. Determine the minimum allowable wire diameter if the criterion for failure is based on yield tensile strength and the safety factor imposed on the design is SF = 2.5. Use the same diameter for both wires. Take m = 90 slugs, 01 = 35° and 0₂ = 50°. - A\ 0₁1 dmin number (rtol=0.01, atol=1e-05) AY 3 B 0₂ in 0000 2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Similar questions

Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
1.3-2 A load of P = 3.0 kips is applied to the connection. The failure stress of the pin material is 25 ksi. Design the diameter of the pin to the nearest 1/16-inch assuming a factor of safety of 2.
Calculate the safety of the cylinder pivot pin in relation to the yield. The tensile yield strength of the pin material is ReL=600MPa. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mmy2 = 798 mm Piston rod = φ32mm Cylinder pivot pin = φ25mm Pliers pivot pin = φ30mm The clamping force of the pliers is 6000N Answer to one decimal place !!
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
At a critical point in a component, the state of stress is given as Oxx = 100 MPa, Oyy = 220 MPa, Oxy = Oyx = 80 MPa and all other stress components are zero. The yield strength of the material is 468 MPa. The factor of safety on the basis of maximum shear stress theory is (round off to one decimal
A ductile bar as shown in figure 1 has a yiel strength of oy = 390 MPa. Force F makes a 30° angle with the positive x axis. Deter- mined the magnitude of F that will cause yielding. Hint: Select the most loaded point in the structure and the failure theory to use according to the material (The standard one for this type of material). Refer to the lecture. 2 y 7 75 mm 500 mm F 300 mm X
1) The cantilever bracket is bolted to a column with three M12 x 1.75 ISO 5.8 bolts. The bracket is made from AISI 1020 hot-rolled steel. Holes for M12 X 1.75 bolts 8 mm thick Find the factors of safety for the following failure modes: shear of 36 | 12 kN bolts, bearing of bolts, bearing of bracket, and bending of bracket. 32 64 Solution: 36 200 Columm
2. A pressure of 40 MPa shall be contained in a pressure vessel with inner diameter 0.30 m. Find the number of M48-5 bolts to be used. Material used to produce the bolts is AISI 1044 steel with maximum tensile stress, o. = 646 MPa. Use a factor of safety =2. M48-5- 40 MPa 1.0 m->
The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. Figure 4 ft 3 ft 3 ft < 1 of 1 Part A If the wire has a diameter of 0.34 in., determine how much it stretches when a load of P = 520 lb acts on the pipe. (Figure 1) Express your answer with the appropriate units. SBD = Submit μA Value Provide Feedback Request Answer Units ?
Three cables are used to hang a traffic light as shown. All three cables have diameter d = 3 mm and are made out of 1045HR steel. If the failure criterion of the overall system is a safety factor SF, = 7 against yielding, what is the maximum traffic light weight that can be hung? Take 0 = 40°, L = 12, and h = 5. W max 1045.1 B h L A 0 Nx0% C