The time, t, it takes to pour a certain volume of liquid from a cylindrical containerdepends on several factors, including the viscosity of the liquid. Assume that for veryviscous liquids the time it takes to pour out 2/3 of the initial volume depends on the initialliquid depth (7), the cylinder diameter (D), the liquid viscosity (i), and the liquid specificweight (). The data shown in the following table were obtained in the laboratory. Formm,these tests, it is known that: 1= 45 mm, D= 67y= 9.60 kN/m?.and(a) Perform a dimensional analysis and based on the data given, determine if variablesused for this problem appear to be correct;(b) If it is possible, determine an equation relating the pouring time and viscosity for thecylinder and liquids used in these tests. If it is not possible, indicate what additionalinformation is needed.H (Ns/m?)t (s)1115172339536183107145

Question is based on liquid poured on container . Dimension of container and unit weight of liquid…

The time, t, it takes to pour a certain volume of liquid from a cylindrical container depends on several factors, including the viscosity of the liquid. Assume that for very viscous liquids the time it takes to pour out 2/3 of the initial volume depends on the initial liquid depth (), the cylinder diameter (D), the liquid viscosity (4), and the liquid specific weight (). The data shown in the following table were obtained in the laboratory. For these tests, it is known that: 1= 45 mm, D = 67 mm, and y= 9.60 kN/m³. (a) Perform a dimensional analysis and based on the data given, determine if variables used for this problem appear to be correct; (b) If it is possible, determine an equation relating the pouring time and viscosity for the cylinder and liquids used in these tests. If it is not possible, indicate what additional informot dod

The time, t, it takes to pour a certain volume of liquid from a cylindrical container depends on several factors, including the viscosity of the liquid. Assume that for very viscous liquids the time it takes to pour out 2/3 of the initial volume depends on the initial liquid depth (), the cylinder diameter (D), the liquid viscosity (4), and the liquid specific weight (). The data shown in the following table were obtained in the laboratory. For these tests, it is known that: 1= 45 mm, D = 67 mm, and y= 9.60 kN/m³. (a) Perform a dimensional analysis and based on the data given, determine if variables used for this problem appear to be correct; (b) If it is possible, determine an equation relating the pouring time and viscosity for the cylinder and liquids used in these tests. If it is not possible, indicate what additional informot dod

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simple viscometer measures the time t for a solid sphere to fall a distance L through a test fluid of density p. The fluid viscosity u is then given by 2PDL if t2 3TDL where D is the sphere diameter and Wnet is the sphere net weight in the fluid. (a) Prove that both of these formulas are dimensionally homogeneous. (b) Suppose that a 2.5 mm diameter aluminum sphere (density 2700 kg/m³) falls in an oil of density 875 kg/m³. If the time to fall 50 cm is 32 s, estimate the oil viscosity and verify that the inequality is valid.
For many applications, it is accurate enough to treat water as incompressible. But for a more detailed understanding of fluid flows, compressibility must be taken into account. Fortunately, the bulk modulus of water is close to constant, so let's model the pressure in a motionless water column assuming that the bulk modulus is a constant, K, = 2.1 GPa. The pressure and density at the top surface of the water column are 6. Po =1000 hPa and P, =1000 kg/m², respectively, and the downward acceleration due to gravity is g =9.8 m/s. Take depth, z, to be positive downward with z = 0 at the top %3D %3D %3D surface. Using the definition of bulk modulus, derive an expression for the density field, p, in terms of pressure, p, and the given parameters. Leave all parameters а. as algebraic. (At this point, your expression should not include z .) b. Starting from hydrostatic balance and the expression in part (a), derive an expression for the pressure field, p(z), in terms of z and the given…
The pressure drop in a system is dependent on the ff quantities: fluid velocity, fluid density, pipe diameter, and throat diameter. How many dimensionless can be formed
Q: In a laboratory experiment it was found that the pressure drop Ap depends on the gate opening h, the overall depth d, the velocity V, mass density p and dynamic viscosity u. Use Buckingham theorem to express these variables in a set of terms.
A tube of diameter 25 mm is used (as shown in the below figure) as a siphon to discharge water from a large open vessel into a drain at atmospheric pressure, (Given: Atmospheric pressure = 101.325 kPa) ignoring friction losses (3) (1) Determine (a)Velocity of flow through syphon (b)Discharge through the syphon (c)The minimum pressure inside the syphon (2) 160 mm 80 mm, 100 mm
Small-diameter, high-pressure liquid jets can be used to cut various materials as shown in the figure below. If viscous effects are negligible, (a) estimate the pressure needed to produce a 0.1-mm diameter water jet with a speed of 730 m/s. (b) determine the flowrate. (a) p = (b) Q = -0.1 mm Kbar cm³/sec
Consider a cylinder of fluid of length L and radius R flowing steadily in the centre of a pipe of radius r as shown below L r R Show that when the flow in the pipe is laminar the pressure loss is directly proportional to the velocity and obeys the equation Where v is the velocity D is the diameter of the pipe
As shown in Figure 1, an ideal gas flows isentropically from a large tank into a converging nozzle and exits to a receiver. The gauge pressure of the ideal gas in the large tank is 80 kPa. The nozzle exit area is 38 cm?. (Assume Pam = 101 kPa). a) Determine Mach Number at section 1, the EXIT mass flow rate and EXIT Mach mumber. b) Calculate the flow area at section 1. V: = 580 km/hr T:= 500 K Exit, A Large Tank P= 166 kPa (abs) Ideal Gas k=1.43 R= 0.2968 kJ/kg.k Vi = 480 kan/hr Figure 1
Water flows steadily from a nozzle into a large tank as shown below. The water then flows from the tank as a jet of diameter d. (a) Using the piezometer tube shown, determine the flow rate through the nozzle. (b) Using the flow rate determine the value d if the water in the tank remains constant. Viscous effects are negligible.
The figure shows a system for delivering lawn fertilizer in liquid form. The nozzle on the end of the hose requires 169.00 kPa of pressure to operate effectively. The hose is smooth plastic with an ID of 25 mm. The fertilizer solution has a specific gravity of 1.13 and a dynamic viscosity of 2.69 x 103 Pa•s. If the length of the hose is 76 m. The coefficient of friction, f= 0.021 and the flow rate is 97 L/min. Required Determine the power delivered by the pump to the solution in kW, to the nearest 100th. Vent 10 m Pump 1.2 m 1.5 m
A piston with a diameter of 15 cm was placed in a cylinder connected to a 1.27 cm inclined tube manometer as shown in the figure. Inside of cylinder and manometer unit weight 9270 N / m3 is filled with an oil. When the weight W is placed on the upper part of the cylinder, the liquid height in the manometer rises from (1) to (2). Piston Find the W weight ignoring the change in position 15cm Piston OIL 30°
Q2: A pressure gage 19.0 ft above the bottom of a tank containing a liquid reads 13.19 psi,another gage at height 14 .0 ft reads 15.12 psi. The density of * :the liquid is 1. 73 slug/ft O 3.10 slug/ft O 0.0216 slug/ft O 4.83 slug/ft O