For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal pressure of 15MPA, d is the inside diameter of the container of 20mm, and t is wall thickness of 10mm. See figure 103. Girth joint d Longitudinal joint For question 103B, the girth stress is equal to 15 MPа О 7,5 МРа 3.75 MPа О 30 МРа

For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal pressure of 15MPA, d is the inside diameter of the container of 20mm, and t is wall thickness of 10mm. See figure 103. Girth joint d Longitudinal joint For question 103B, the girth stress is equal to 15 MPа О 7,5 МРа 3.75 MPа О 30 МРа

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 5 of 15 The plate of thickness, t 5 mm, is loaded with the following stress; o, - 100 MPa, o, - -60 MPa, E- 200 GPa, v = 0.33. If a 160 mm, and b 200 minn, D. ► X A Calculate the change in thickness (mm). Select the correct response:
Brass ninum Problem 2 Two 10-kN forces are applied to a 20 x 60-mm rectangular bar as shown. Determine the stress at point A when (a) b = 0, (b) b = 10 mm, (c) b = 25 mm. 10 mm 10 mm 30 mm 10 kN 30 mm 10 kN 25 mm
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47
A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid A36 steel with a 20 mm diameter (E = 200 GPa). Outer sections DA and BC are solid red brass (E = 101 GPa) with a 50 mm diameter. A previous analysis by a now departed coworker correctly determined that the internal normal stress in DA was 54.952 MPa compression. You are asked to determine the horizontal displacements of joints A and B.
1. Steel tape used in a tape measure has a thickness of 0.0065 in. If the allowable stress is 68 ksi, what is the smallest spool diameter the tape can be wrapped around? [in.] Spool diameter D →Tape thickness t
Part A The solid aluminum shaft has a diameter of 60 mm. Set T = 1810 N-m. (Figure 1) Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate units. HA ? (Tabs )max = Value Units Submit Request Answer Figure 1 of 1 E Provide Feedback 300 N•m 600 N m T, 900 N•m
Homework 8: A (20°C) a rigid beam in placed upon the rods shown in figure: 1) Determine the magnitude of uniformly distributed load w (kN/m) so that beam remains horizontal when temperature of steel becomes to (100°C). 2) Find the stress developed in each rod. Steel A, = 1000mm², as = 12 * 10-6 , E, = 200GPA, L = 500mm %3D %3D Aluminum Aal 1500mm2, aal = 23 * 10-6 , Eal = 70GPA, L = 300mm %3| Rigid beam w (kN /m) A C steel Aluminum 3m 3m
Q2/ The rigid, horizontal slab is attached to two identical copper rods. There is a gap A=0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85°C. Use the following data: Each copper rod Aluminum rod A (mm²) 500 400 a (°C) 16.8 x 10-6 23.1 x 10-6 E (GPa) 120 70 Copper TA Aluminum Copper L=3m A= 1500 mm E=120 GPa a = 16.8 x 10-C Copper -750 mm-
I RevieW The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Part A Determine the state of stress at point B. Express your answers, separated by commas, to three significant figures. IVα ΑΣφ. vec ? OB =, (Tzy)B =, (T2)B = ksi (C), ksi, ksi Figure 1 of 1 > Submit Request Answer < Return to Assignment Provide Feedback 9 in. 200 lb 300 lb 1200 lb in.
The tube is subjected to a torque of 749 N-m Figure 62°5 6 mm 100 mm 4 mm 4 mm 60 mm B 6 mm 1 of 1
A cylindrical tank 7.5 in diameter is H m high. If the tank is filled with water, determine the aximum height H if the tank plating is 15mm thick and If the material is capable of the lowable stress of 30MPa. ||| U <
A strain gage is mounted at an angle of 30° with respect to the longitudinal axis of the cylindrical pressure. The pressure vessel is fabricated from aluminum [E - 10,000 ksi; v - 0.33], and it has an inside diameter of 54 in. and a wall thickness of 1.00 in. If the internal pressure in the cylinder is 702 psi, determine the expected strain gage reading in ue. O 817 uE O 602 µE O 522 µE O 637 µE O 393 uE