The T section shown is the cross-section of a beam formed by joining two rectangular pieces of steel together. The beam is subjected to a maximum shearing force of 60 kN. Use NA = 34 mm from the %3D top and INA = 10.57 × 106 mm4, determine the shearing stress at the neutral axis. 200 mm 40 mm 100 mm 20 mm 3.28 MPa 2.38 MPa

The T section shown is the cross-section of a beam formed by joining two rectangular pieces of steel together. The beam is subjected to a maximum shearing force of 60 kN. Use NA = 34 mm from the %3D top and INA = 10.57 × 106 mm4, determine the shearing stress at the neutral axis. 200 mm 40 mm 100 mm 20 mm 3.28 MPa 2.38 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain 6x = 0.005, DA has a normal strain e, = 0.004 at D, y = 0.01rad determine the shear strain at point E with respect to the x and y' axes. 600 mm 600 mm
What is the shearing stress developed at the neutral axis of the beam with a circular cross section having a diameter of 17 mm and a shear force V = 29 kN. Assume that the shearing stress is uniformly distributed across the neutral axis. Answer must be in MPa.
Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain Ex = 0.005, DA has a normal strain ey = 0.004 at D, Yxy = 0.01rad determine the shear strain at point E with respect to the x' and y' axes. 600 mm- 600 mm E D
Detemine the principal stress acting at point B, which is located just on the web, below the horizontal segment on the cross section Show the results on a properly oriented element located at this point. Although it is not very accurate, use the shear formula to calculate the shear stress. -AO mm- 300 mm 150 mm 12 mm 130 mim 15 mm 6 kN
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.
PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E=200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M ТЕСНА
Athin rectangular plate is uniformly deformed as shown. If L₁ = 0.125 in. and L₂ =0.135 in., determine the shear strain Yxy at P. 20 in. R 14 in. O -2460 μrad O -3070 μrad O -2800 μrad O -3390 μrad O -4670 μrad L₂ x
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
The lower end of the three bars in the figure are at the same level before the rigid homogeneous 18 Mg block is Each steel bar has an area of 600 mm2 and E=200 GPa. For the bronze bar, the area is 900 mm2 and E=83 GPa. a.) Compute the stress developed in the bronze bar. b.) Compute the stress developed in the steel bar and c.)Compute the elongation of the bars.
A flat steel bar, 25mm wide by 6mm thick and 1 m long, is bent by couple applied at the ends so that the midpoint deflection is 20mm. Use E=200 GN/m^2. Compute: a. the maximum stress in the bar (MPa) b. the magnitude of the couples(N-mm) Round to the nearest whole number.
2)For the supporting frame shown below: a) Determine the internal forces acting at section a-a. b) Determine the stress components that act at points A and B. IN = 2.6525x10-7 mª -300 mm 150 mm 2.5 kN a 12 mm 6 mm 6 mm 6 mm 36 mm'36 mm Section a – a