Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S= 160 MPa, S= 130 MPa, and Sy= 85 MPa. Assume B = 55°. Sxy Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the subsequent parts of this GO exercise. For this Mohr's circle, point x, which represents the státe of stress on the x face of the stress element, should appear: O Below and to the right of the circle center. O Above and to the right of the circle center. O Below and to the left of the circle center. O Above and to the left of the circle center.

Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S= 160 MPa, S= 130 MPa, and Sy= 85 MPa. Assume B = 55°. Sxy Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the subsequent parts of this GO exercise. For this Mohr's circle, point x, which represents the státe of stress on the x face of the stress element, should appear: O Below and to the right of the circle center. O Above and to the right of the circle center. O Below and to the left of the circle center. O Above and to the left of the circle center.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider a point in a structural member that Is subjected to planevess. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of Sx 320 MPa, Sxy = 230 MPa. Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the subsequent parts of this GO exercise. For this Mohr's circle, point x, which represents the state of stress on thex face of the stress element, should appear: O Above and to O Above and to the left of the circle center. right of the circle center. O Below and to the left of the circle center. O Below and to the right of the circle center.
The state of stress at a point with ox, oy, and txy as shown. Analyze the state of stress at the point using the Mohr's circle of stress. Determine the following a) Principal stress, b) Maximum in-plane shear stress and c) Normal stress on the plane defined by x' axis where the angle is 25 degrees. Ne To 0. ox x TEV
Consider a point ina structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of 5, - 30 MPa, 5,- 160 MPa, S- 145 MPa, and = 35". Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the subsequent parts of this GO exercise. For this Mohr's circle, point x, which represents the state of stress on the xface of the stress element, should appear: O Above and to the left of the circle center. O Below and to the right of the circle center. O Below and to the left of the circle center. O Above and to the right of the circle center. Save for Later Attempts: 0 of 1 used Submit Answer Part 2
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of Sx = 145 MPa, Sy = 95 MPa, and S,y = 75 MPa, B = 50°. Sxy Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the subsequent parts of this GO exercise. For this Mohr's circle, point x, which represents the state of stress on the x face of the stress element, should appear: O Above and to the left of the circle center. O Below and to the left of the circle center. O Above and to the right of the circle center. O Below and to the right of the circle center.
Q.2) A state of stress is specified as shown in Figure (2), By using Mohr's circle determine the normal and shearing stresses and their directions on: a- The principal planes? b- The planes of maximum shearing stress? c- The planes whose normals are at (+50°) and (+140°) with x-axis? show your results on complete sketches of differential elements. 80 MPa 50 MPa YA 40 MPa + 50 MPa, 80 MPa 40 MPa Figure (2)
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of S- 160 MPa, S 85 MPa, and Sy- 45 MPa. Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the subsequent parts of this GO exercise. For this Mohr's circle, point x, which represents the state of stress on the x face of the stress element, should appear: O Below and to the left of the circle center. O Belowand to the right of the circle center. O Above and to the left of the circle center. O Above and to the right of the circle center.
www The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy = 210 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume 3 = 47° Selle Answer: Sn = Snt = S, 6 ← T 5 S., MPa MPa
The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 100MPA and S, = 245 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 55°. Sy Answer: Sn = MPa Snt = MPa
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx - 60 MPa and Sy = 210 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume 3 = 47°. Answer: Sn = Snt= S B Sx MPa MPa
The state of stress at a point is shown with respect to the xy-axes. Determine the equivalent state of stress with respect to the x'y' - axes. What is the shear stress with respect to the x' y' -axes if M = 76.86, N = 72.06, and S = 114.17. Round off final answer to four decimal places. M ksi 60° N ksi X S ksi
2. For the state of stress shown in the figure, determine normal and shearing stresses on the planes whose normal are at +60° and +150° with the x-axis. Show all results using Mohr's Circle diagram. 8 ksi 8 ksi 10 ksi
Problem example Example 7-5: The state of plane stress at a point with respect to the xy- axes is shown in the figure. Using Mohr's circle, determine (a) The principal stresses and principal planes and sketch the results. (b) The maximum shear stress. Draw Mohr's circle 78.75 MPa 33.61 MPa 22.11 MPG 3. Op