the machine element was made from steel by combining a cylindrical base with a cone on top, then cutting a semicylinder from the base. (steel density = 7850kg/m3) a. what's the x-coordinate of center of mass of the entire assembly b. what's the y-coordinate of center of mass of entire assembly c. what's moment of inertia of the entire assembly with respect to the y-axis

the machine element was made from steel by combining a cylindrical base with a cone on top, then cutting a semicylinder from the base. (steel density = 7850kg/m3) a. what's the x-coordinate of center of mass of the entire assembly b. what's the y-coordinate of center of mass of entire assembly c. what's moment of inertia of the entire assembly with respect to the y-axis

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 1RQ: Information such as tolerances and scale can be found in the________ of an engineering drawing.

See similar textbooks

Similar questions

1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At which point(s) of the cross-section the normal stress is zero? b) Determine the maximum compressive and tensile bending stress in the beam.
Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.
300 N 36 mm 12 mm 120 mm В 30 mm A C D 6 mm 96 mm 42 mm| 30 mm 300 N
28 cm a? 100 cm 30° 15 cm
620 mm 125 350 mm
(b) The mass of the object suspended at G is 100 kg, as demonstrated in Figure Q5(b). Determine the reaction on member CDE at C and E.
B X m 0.2 m An astronaut, still on earth and just wearing his suit so you know he's an astronaut, is holding a space chest, also still on earth. The space chest along with the space gold has a mass of 76 kg and the box has a height of 0.6 meters. Find the distance from the edge of the desk to B: Determine the smallest force that the astronaut can apply at B to make a moment opposite of E. FB Newtons. Determine the angle of the force. degrees.
5) Chapter 3: Problem 3.2: (SI Units) During a tensile test, the starting gage length=100.0 mm and the cross-sectional area =150 mm2. During testing, the following force and gage length data are collected: (1) 17,790 N at 100.2 mm, (2) 23,040 N at 103.5 mm, (3) 27,370 N at 110.5 mm, (4) 28,910 N at 122.0 mm, (5) 27,400 N at 130.0 mm, and (6) 20,460 N at 135.1 mm. The final data point (6) occurred immediately prior to failure. Yielding occurred at a load of 19,390 N (0.2% offset value), and the maximum load (4) was 28,960 N. (a) Plot the engineering stress strain curve. Determine (b) yield strength, (c) modulus of elasticity, (d) tensile strength, and (e) percent elongation.
21 The shear strain in a rod is the deformation per unit length
What is the worst-case distance between the bottom surface of the slot and the bottom surface of the part in the drawing below? B 4.000-4.020 1.475 O 1.030 2.950 B 4.00 O 1.450 O 1.500 1.000-1.010 .010M ABM 2.00 A
100 mm В A 30 mm
Ixo and Iyo of a quarter circle with a diameter of 50cm (Answer format: Ixo= , Iyo=)