Two cylinders are to be press-fitted together so that the principal stress with the greatest absolute value is not to exceed 60 percent of the yield strength of the material. Both members are made of a steel with a yield strength of 80 ksi. E = 30 Mpsi, and v = 0.29. The nominal diameters of the cylinders are 1.0, 1.5, and 2.0 in. (a) Determine the maximum acceptable radial interference and the corresponding interface pressure. (b) Under the conditions of part (a) plot the stress distributions for each member.

Two cylinders are to be press-fitted together so that the principal stress with the greatest absolute value is not to exceed 60 percent of the yield strength of the material. Both members are made of a steel with a yield strength of 80 ksi. E = 30 Mpsi, and v = 0.29. The nominal diameters of the cylinders are 1.0, 1.5, and 2.0 in. (a) Determine the maximum acceptable radial interference and the corresponding interface pressure. (b) Under the conditions of part (a) plot the stress distributions for each member.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.8P: Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the...

See similar textbooks

Similar questions

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
The assembly shown below consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 115 GPa; α = 18.7 x 10-6 /°C] has an outside diameter of 50 mm and an inside diameter of 35 mm. The ceramic core [E = 290 GPa; α = 3.1 x 10-6 /°C] has a diameter of 35 mm. At a temperature of 15°C, the assembly is unstressed. Determine the largest temperature increase that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 80 MPa.
At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 139°C. Determine the normal stress in the aluminum rod.
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.8mm A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.540mm
A steel [E=200 GPa] rod with a circular cross section is 10 m long. Determine the minimum diameter required if the rod must transmit a tensile force of 260 kN without exceeding an allowable stress of 240 MPa or stretching more than 10 mm.
A closed-ended compound cylinder is formed by shrinking a steel [E = 200 GPa; v = 0.3] tube that has an external diameter of 320 mm and an internal diameter of 250 mm onto a brass [E =100 GPa; v = 0.35] tube that has an internal diameter of 200 mm. The radial interference is 0.050 mm. Determine the largest circumferential stress in the finished assembly after an internalpressure of pi = 50 MPa is applied.
Determine the principal stresses at points A and B of the cylinder. Consider: L = 70 mm; d = 20 mm; F = 12 kN; P = 15 kN; T = 800 Nm.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 22 ksi, and the normal stress in steel rod (3) must be limited to 13 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 7 kips, Q = 2 kips, R = 16 kips and S = 20 kips.
The d = 16-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 10 mm. The rod head has a diameter of a = 32 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 140 MPa, the punching shear stress in the support plate cannot exceed 90 MPa, and the bearing stress between the rod head and the support plate cannot exceed 125 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α= 10.5 × 10−6/°F] rod (1) and a solid 1.49-in.-diameter bronze [E = 15300 ksi, v = 0.15, α= 7.6 × 10–6/°F] rod (2). Assume L1=11 in., L2=22 in. If the supports at A and C are rigid and the assembly is stress free at 16°F, determine:(a) the normal stresses σ1, σ2 in both rods at 213°F (positive if tensile, negative if compressive).(b) the displacement uB of flange B (positive if to the right, negative to the left).(c) the change in diameter Δd1 of the aluminum rod.
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.