Required information The upper surface of a 85-cm-thick solid plate (k= 237 W/m-K) is being cooled by water with temperature of 20°C. The upper and lower surfaces of the solid plate maintained at constant temperatures of 60°C and 120°C, respectively. Given: The thermal conductivity of the solid plate is given as k = 237 W/m K. The thermal conductivity of water at the film temperature of T, = W/m/k. (T+T) = (60°C + 20°C)/2 = 40°C is kTuid = 0.631 Determine the water convection heat transfer coefficient. The water convection heat transfer coefficient is W/m2 K.

Required information The upper surface of a 85-cm-thick solid plate (k= 237 W/m-K) is being cooled by water with temperature of 20°C. The upper and lower surfaces of the solid plate maintained at constant temperatures of 60°C and 120°C, respectively. Given: The thermal conductivity of the solid plate is given as k = 237 W/m K. The thermal conductivity of water at the film temperature of T, = W/m/k. (T+T) = (60°C + 20°C)/2 = 40°C is kTuid = 0.631 Determine the water convection heat transfer coefficient. The water convection heat transfer coefficient is W/m2 K.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.32P

See similar textbooks

Similar questions

Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
The handle of a saucepan, 30 cm long and 2 cm in diameter, is subjected to 100 degree Celsius temperature during a certain cooking operation. The average unit surface conductance over the handle surface is 7.35 W/m2 degree in the kitchen air at 24 degree Celsius. The cook is likely to grasp the last 10 cm of the handle and hence the temperature in this region should not exceed 38 degree Celsius. What should be the thermal conductivity of the handle material to accomplish it? The handle may be treated as a fin * .insulated at the tip
A wall with a thermal conductivity of 0.4 W/m-°C is maintained at 45°C. The heat transfer through the wall is 220 W. The wall surface area is 2.0m² and its thickness is 1.5 cm. Determine the temperature at the other surface.
A plane wall 15 – cm thick has a thermal conductivity given by the relation k = 2.0 + 0.0005 T, W/m – K where T is in Kelvin. If one surface of this wall is maintained at 150 oC and the other at50 oC, determine the rate of heat transfer per square meter. Sketch the temperaturedistribution through the wall.
A 2x2-m glass window, 1 cm thick is subjected to 10°C and 3°C inner and outer temperatures respectively. If the thermal conductivity of the glass is 0.78 W/m-°C, what is the amount of heat loss, in kl, through the glass over a period of 5 hours?
H.W. Q: An aluminum pan whose thermal conductivity is 237 W/m-°C has a flat bottom with diameter 20 cm and thickness 0.4 cm. Heat is transferred steadily to boiling water in the pan through its bottom at a rate of 800 W. If the inner surface of the bottom of the pan is at 105°C, determine the temperature of the outer surface of the bottom of the pan. 105°C 0.4 cm Answer: T= 105.43 °C 800 W 7
Question 2 Figure 2 shows the cross-sectional of inner and outer surfaces of a 4 m x 7 m brick wall with thickness of 30 cm and thermal conductivity 0.69 W/m.K. The inner and outer surfaces are to be maintained at temperatures of 26°C and 8°C, respectively. Determine the rate of heat transfer through the wall, in W. Answer: 26°C Brick wall 30 cm Figure 2 8°C
Question 4 The window of a room is made of 5 mm thick glass which has a thermal conductivity of 1.4 W/m-K. A heater is used to maintain the room temperature at 22 °C. Take the convection heat transfer coefficients on the outer surface of the window to be 12 W/m²-K. Take appropriate assumptions while solving this problem. (a) T₁-15°C TA -A=1m x 3m 3m², k=1.4 W/m-K I L=0.005m Figure Q2 ** -T₂=5°C Find the convection heat transfer coefficients on the inner surface of the window.
A 4-mm and 2-m-long electric wire is tightly wrapped with a 2-mm-thick plastic cover whose thermal conductivity is k =0.1 W/m-°C. Electrical measurements indicate that a current of 10 A passes through the wire and there is a voltage drop of 10 V along the wire. If the insulated wire is exposed to a medium at =20 °C with a heat transfer coefficient of h=10 T. W/m2.°C, determine the temperatures T1 and T2 as shown in the figure below. Also determine whether doubling the .thickness of the plastic cover will increase or decrease T2 T
1/ The roof of an electrically heated home is 6 m long, 8 m wide, and 0.25 m thick, and is made of a flat layer of concrete whose thermal conductivity is k = 0.8 W/m.°C (Figure. 1-3). The temperatures of the inner and the outer surfaces of the roof one night are measured to be 15°C and 4°C, respectively, for a period of 10 hours. Determine the rate of heat loss through the roof at night