Q10/A large slab at 350°C suddenly has its surface exposed to convection at30°C with h = 80 W/m2K. Determine the temperatures at a depth of 40 mmand at the surface after 300 seconds, given thermal diffusivity5.6 x10-6 m2 /s and conductivity = 25 W/mK. Answer: 334.6°C, 306.7°C

Answered: Image /qna-images/answer/0521b09d-a08a-4632-b95d-74736f8e61f0.jpg

Q10/ A large slab at 350°C suddenly has its surface exposed to convection 30°C with h = 80 W/m²K. Determine the temperatures at a depth of 40 m and at the surface after 300 seconds, given thermal diffusivity 5.6

Q10/ A large slab at 350°C suddenly has its surface exposed to convection 30°C with h = 80 W/m²K. Determine the temperatures at a depth of 40 m and at the surface after 300 seconds, given thermal diffusivity 5.6

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.17P: The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with...

See similar textbooks

Similar questions

1.29 A spherical interplanetary probe with a 30-cm diameter contains electronic equipment that dissipates 100 W. If the probe surface has an emissivity of 0.8, what is its surface temperature in outer space? State your assumptions in the calculations.
The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with dimensions 0.1m0.5m is determined to be 125 W when the surface of the plate is kept at 30C. What is the average convection heat transfer coefficient between the plate and the air?
Steel is sequentially heated and cooled to relieve stresses and to make it less brittle. Consider a 100 mm thick plate that is initially at a uniform temperature of 300 °C and is heated on both sides in a gas fired furnace for which To 700 °C and h=500 W/m². K. How long will it take the coldest spot to reach 550 °C in the plate? Materials properties are given in this graph. == = Steel plate: 11 T₁ = 300°C T(0,t) = 550°C L = 50 mm Combustion gases p=7800 kg/m3 Cp = 500 J/kg-K k = 45 W/m-K T∞ = 700°C h = 500 W/m²-K
A 0.1 m diameter long rod at 20 °C is to be heated by a hot fluid of 200 °C. How long does it take the rod temperature to reach 70% of the fluid temperature if the followings are given? Convection coefficient h = 10 W/m2K Thermal conductivity k = 20 W/mK Thermal diffusivity a = 10-5 m2/s
Find the temperature profile of the rectangular plate 4m x 4m, whose temperature at the side are given below: Take delx= del y= 1 m. 100 C 75 C OC 50 C
A thermometric well is placed in a pipe having diameter of 55 mm. Pipe wall temperature is 100°C and heat transfer coefficient inside the pipe is 300 W/m² K. Thickness of thermowell is 1.2 mm and its length is 50 mm. Thermal conductivity of thermowell material. Is 30 W/mK. If the temperature of the gas flowing through the pipe is recorded by thermometer as 200°C, determine the true temperature of gas. If the error in gas temperature is to be reduced by 80% by increasing the length of thermowell, determine the new length of thermowell. Draw a sketch of this thermowell. Take perimeter to area ratio for thermowell as 1/T (T= thickness).
It is designed in such a way that the internal temperature of a commercial heat treatment furnace can reach up to 165 oC. All surfaces of the furnace consist of firebrick (10 cm), insulation material and sheet metal (3mm) from the inside out. Given that the outdoor temperature is 22 oC, the outer sheet will be allowed to go up to 35 oC, which is a temperature that will not disturb in contact with hands. In this case, determine the insulation material thickness to be used. The thermal conductivity coefficient of the insulation material is insulation 0.066 W / m oC, 60 W / m oC for sheet metal and 115 W / m oC for firebrick. Indoor heat transfer coefficient will be accepted as 25 W / m2 oC and 12 W / m2 oC for outdoor environment.
3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A= 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. -02-1
A:Find the amount of heat transferred through an iron fin of thickness 5 mm, length 10 cm and width 100 cm. Also determine the temperature difference e at the tip of the fin at: 1- adiabatic tip, 2-heat convection at the tip. Assuming the atmospheric temperature of 28°C K=50 w/mK, h=10 w/m’K, O,=80°C. B-Why is the dimensional heat flow assumption important in the analysis of fins problems? C- Why are the annular fins more efficiency than others?.
b. Consider a large plane wall of thickness L = 0.25 m, thermal conductivity k= 0.77 W/m-K, and surface area A = 15 m. The outside wall is subjected to convection with T1 = 100 °C and h, = 5 W/m? · K and the inside wall is maintained at constant temperatures of T2 = 50 °C, respectively, as shown in Fig. 2. Determine: i. express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, and obtain a relation for the variation of temperature in the wall by solving the differentiai equation 11. -T2
The handle of a saucepan, 30 cm long and 2 cm in diameter, is subjected to 100 degree Celsius temperature during a certain cooking operation. The average unit surface conductance over the handle surface is 7.35 W/m2 degree in the kitchen air at 24 degree Celsius. The cook is likely to grasp the last 10 cm of the handle and hence the temperature in this region should not exceed 38 degree Celsius. What should be the thermal conductivity of the handle material to accomplish it? The handle may be treated as a fin * .insulated at the tip
During daytime, the outside air temperature is measured at Ta = 35 °C. A house with an inside temperature of Tin = 20 °C is separated from the outside by a brick wall as shown in Figure 1. i Briefly discuss what will happen in terms of heat transfer process and the mode of heat transfer involved. ii. Identify the parameters that affect the rate of heat transfer in this case T. = T = 35°C 20°C Brick wall