Q1: For the shaft shown in Figure, which is constructed of two circular cross-section shafts A. and B connected in series. if P=8 kN, For both arrangements (a) and (b), find the following: i. The sresses in each shaft and the total extensions A neglecting the gravity effect. The sresses in each shaft taking the gravity into account. From above calculations, what do you conclude? Can the weight be neglected? Type A B E in GN/m² 200 300 Density kg/m³ 7800 5000 100mm Die B 6mm (a) Cross Section Circle D=100 mm Circle D-60 mm Diameter 12 Diameter 180mm A (b) 200- WwW.DRE

Q1: For the shaft shown in Figure, which is constructed of two circular cross-section shafts A. and B connected in series. if P=8 kN, For both arrangements (a) and (b), find the following: i. The sresses in each shaft and the total extensions A neglecting the gravity effect. The sresses in each shaft taking the gravity into account. From above calculations, what do you conclude? Can the weight be neglected? Type A B E in GN/m² 200 300 Density kg/m³ 7800 5000 100mm Die B 6mm (a) Cross Section Circle D=100 mm Circle D-60 mm Diameter 12 Diameter 180mm A (b) 200- WwW.DRE

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.18P: A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed...

See similar textbooks

Similar questions

A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
Repeat the previous problem using sx= 12 MPa.
A heavy flywheel rotating at n revolutions per minute is rigidly attached to the end of a shaft of diameter d (see figure). If the bearing at A suddenly freezes, what will be the maximum angle of twist <£of the shaft? What is the corresponding maximum shear stress in the shaft? (Let L = length of the shaft, G = shear modulus of elasticity, and / = mass moment of inertia of the flywheel about the axis of the shaft. Also, disregard friction in the bearings at Sand Cand disregard the mass of the shaft.) Hint: Equate the kinetic energy of the rotating flywheel to the strain energy of the shaft.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
-15 Repeat the preceding problem using ??. = - 750 psi.
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
Repeat the preceding problem using sx= 5.5 MPa. ??y= 4 MPa. and txy= 3.2 MPa.
From the figure below, a shaft consists of different sections. Bar (a) is a hollow bar and has an outer d = 0.2m and thickness of 10 mm. Bar (b) is also a hollow bar with outer d = 0.15 m with same thickness as bar (a). If T1= 42,000 N-m and T2 = 18,000 N-m, Find the max shear stress in bar (b). Answer in MPa.
Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure , Determine the angle of rotation at the free end. D2 D1 T (kN-m) L(m) T(kN-m) D1 (mm) D2 (mm) G (GPa) 29 60 160 80